RP100-482.505DP

Features ● ● ● ● ● ● ● ● ● ● Single Output up to 25A Dual Outputs Total Power up to 100W Input/Output 1.6kVDC Isolation Adjustable Output Voltage Under-Voltage Lockout No Minimum Load Industry Standard Footprint Fixed Operating Frequency Halt Tested Compact 61.0 x 57.91 x 12.7mm Package High Efficiency to 90% INNOLINE DC/DC-Converter RP100S_DI Series 100 Watt Isolated Single & Dual Output Selection Guide Part Number Input Voltage (VDC) 36 – 75 36 – 75 36 – 75 36 – 75 36 – 75 Input Voltage (VDC) 36 – 75 36 – 75 Output Voltage (VDC) 1.8 2.5 3.3 5 15 Output Voltage V1 / V2 (VDC) 5 / 3.3 5 / 2.5 3.3 / 2.5 Output Current (A) 25 25 25 20 6.66 Output Current I1 / I2 (A) 20 / 25 20 / 25 25 / 25 Line Load Regulation Regulation (mV) (mV) 4 5 7 10 30 Line Regulation V1 / V2 (mV) 25 / 16.5 25 / 12.5 16.5 / 12.5 6 8 10 15 45 Input Efficiency (9) Current(8) (A) % 1157 1608 2022 2480 2507 86 87 90 90 90 Single Output RP100-481.8S RP100-482.5S RP100-483.3S RP100-4805S RP100-4815S Part Number Dual Output RP100-483.305DI RP100-482.505DI Load Input Efficiency Regulation Current(8) (9) V1 / V2 (mV) (A) % 25 / 16.5 25 / 12.5 16.5 / 12.5 2.39 2.45 2.44 87 85 85 RP100-482.53.3DI 36 – 75 Notes: 1. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used, the +Vsense should be connected to its corresponding +Vout and likewise the -Vsense should be connected to its corresponding -Vout. 2. Single: Measured with a 1µF M/C and a 10µF T/C. Dual: For each outputs. 3. An external filter capacitor is required for normal operation. The capacitor should be capable of handing 1A ripple current for 48V models. RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90mΩ. 4. Single: The negative / positive logic and length are optional ( see table ). The pin voltage is referenced to negative input. Dual: The ON/OFF control function. There are positive logic ( standard ) and negative logic ( option ). The pin voltage is referenced to negative input. To order negative logic ON/OFF control add the suffix-N. ( Ex:RP100-483.305I/N ) 5. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40°C. ( Ground fixed and controlled environment ) 6. Heat sink is optional and P/N: 7G-0021, 7G-0022, 7G-0023, 7G-0024. 7. The RP100 meets level A and level B conducted emissions only with external components connected before the input pin to the converter. 8. Maximum value at nominal input voltage and full load. 9. Typical value at nominal input voltage and full load. The dual efficiency test condition: RP100-483.305DI @ 5V/12A and 3.3V/12A RP100-482.505DI @ 5V/12A and 2.5V/16A RP100-482.53.3DI @ 3.3V/18A and 2.5V/16A 10. BASEPLATE GROUNDING: Base-plate should be grounded at one of four screw bolts prior to operation. 11. The converter is provided by basic insulation. 12. “N” for Negative remote ON/OFF. N 13. “P” for Positive remote ON/OFF. P www.recom-international.com July-2006 195 INNOLINE DC/DC-Converter Specifications (refer to the standard application circuit, Ta: 25°C) Input Voltage Range Over-Voltage Lockout Start-up Voltage Over-Voltage Lockout Shuntdown Voltage Unde-Voltage Lockout Start-up Voltage Unde-Voltage Lockout Shuntdown Voltage Input Filter (Note 3) Input voltage variation Input Surge Voltage 100ms max Start up time Input Reflected-Ripple Current (5Hz to 20Hz, 12µH Source inpedance) Remote ON/OFF (Note 4) Single (Positive logic) Single (Negative logic) Dual (Positive logic) Dual (Negative logic) Continuous Output Power Output Voltage Accuracy (full load and nominal Vin) Output Voltage Adjustment (Note 1) Minimum Load Line Regulation Load Regulation low line to high line at full load Single 0% to 100%full load Dual 0% to 100% full load Dual for each Outputs 36-75VDC Dual Dual Single Dual Single Dual dv/dt Single RP100-S_DI Series 48V nom. 76.5V typ. 78.5V typ. 34V typ. 35V typ. 32V typ. 33V typ. L-C type 5V/ms max (Complies with ETS300 132 part4.4) 100VDC 25ms typ. 20mAp-p Nominal Vin and constant resistive load Single Single ON=Open or 3.0V < Vr < 15V, OFF=Short or 0V < Vr < 1.2V, ON=Short or 0V < Vr < 1.2V, OFF=Open or 3.0V < Vr < 15V, ON=Open or 3.0V < Vr < +Vin, OFF=Short or Vr < 1.2V, ON=Short or 3.0V < Vr < +Vin, OFF=Open or Vr < 1.2V. Single Dual Single Dual IIN=50µA max. IIN=1mA max. IIN=1mA max. IIN=50µA max. 100W max. ±1.5% ±1.0% +10%, -20% ±10% 0% See table See table 10% of Vout 100mVp-p ±0.02%/ºC 200µs 115% ~ 130% of Vout 3.0V 3.9V 6.2V 110% ~ 140% of Iout Rated Hiccup, Automatic recovery up to 90% Continued next page Remote Sense (Note 1) Ripple and Noise 20MHz bandwidth (Note 2) Temperature Coefficient Transient Response Recovery Time (25% load step change) Over Voltage Protection threshold (Hiccup) Single & Dual 2.5V 3.3V 5V Over Current Protection threshold Short Circuit Protection Efficiency (at nominal input voltage, full load) 196 July-2006 www.recom-international.com INNOLINE DC/DC-Converter Specifications (refer to the standard application circuit, Ta: 25°C) Isolation Voltage Input to Output Input to Case Output to Case Single Dual Single Dual RP100-S_DI Series 1600VDC min. 1000VDC min. 1000VDC min. 10 MΩ min. 10 GΩ min. 2500pF max. 1500pF max. 300KHz typ. Single Dual for Base-plate -40ºC to +100ºC 110°C 105°C -55°C to +125°C 95% MIL-STD-810D 10 ~ 55Hz 2G, 3minutes period, 30minutes analog EN55022 (Note 7) EN55022 (Note 7) EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Dual X, Y and Z Level A Level B Level A Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Non-conductive black plastic Aluminum base-plate Dual Single Dual Single Dual Silicon (UL94-V0) 55g 105g 3 2000 x 10 hours 3 1004 x 10 hours Isolation Resistance Isolation Capacitance Operating Frequency Operating Base-plate Temperature Range ( Note 6 ) Over Temperature Protection Storage Temperature Range Humidity max., Non-condensing Thermal Shock Vibration Conducted Emissions Radiated Emisssions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Case Material Base material Potting material Weight MTBF ( Note 6 ) www.recom-international.com July-2006 197 INNOLINE Characteristics DC/DC-Converter RP100-S_DI Series Efficiency vs Output Load 100 90 80 Efficiency (%) 70 60 50 10 20 30 40 50 60 70 80 90 100 Output Power (%) Ta=25°C 48V Input Without Heatsink 110 90 70 1.) LFM590 2.) LFM400 3.) LFM200 4.) LFM20 Output Power (%) 50 30 10 -40 -20 0 20 40 60 1 2 34 80 100 Ambient Temperature (°C) 48V Input With Heatsink (7G-0022) 110 90 70 1.) LFM590 2.) LFM400 3.) LFM200 4.) LFM20 Output Power (%) 50 30 10 -40 -20 0 20 40 60 1 2 34 80 100 Ambient Temperature (°C) 198 July-2006 www.recom-international.com INNOLINE DC/DC-Converter Package Style and Pinning (mm) RP100-S_DI Series 3rd angle projection Single Output 57.91 60.96 12.70 5.08 48.26 Side View 50.80 4xM3 x 0.5 ( Note 10) Pin Connections Pin # Function 1 –Vin 2 Case 3 Remote ON/OFF 4 +Vin 5 –Vout 6 –Vsense 7 Trim 8 +Vsense 9 +Vout XX.X ± 0.5 mm XX.XX ± 0.25 mm Pin pitch tolerance 0.35mm Pin Ø 1.016 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm 1 2 35.56 15.24 3 4 5 6 7 8 9 17.78 10.16 25.40 Bottom View External Output Trimming Output can be externally trimmed by using the method shown below. Product Options Table Option Negative remote ON/OFF logic, 0.20” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length Negative remote ON/OFF logic, 0.11” pin length L K P S M Suffix 7 Trim Up RU 6 Trim Down RD Positive remote ON/OFF logic, 0.20” pin length Positive remote ON/OFF logic, 0.145” pin length Positive remote ON/OFF logic, 0.11” pin length 8 7 Example: RP100-483.3S/P www.recom-international.com July-2006 199 INNOLINE DC/DC-Converter Package Style and Pinning (mm) RP100-S_DI Series 3rd angle projection Dual Output 57.91 5.08 60.96 12.70 Side View 48.26 50.80 4xM3 x 0.5 ( Note 10) Pin Connections 1 35.56 15.24 3 4 2 5 6 Bottom View 7 8 9 10 25.40 10.16 40.64 Pin # Function 1 –Vin 2 Case 3 Remote ON/OFF 4 +Vin 5 +V2 6 –V2 (Com) 7 V2 Trim 8 +V1 9 +V1 (Com) 10 V1 Trim XX.X ± 0.5 mm XX.XX ± 0.25 mm Pin pitch tolerance 0.35mm Pin Ø 1.016 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm 2.032 mm 1.016 mm 2.032 mm 2.032 mm 1.016 mm External Output Trimming Output can be externally trimmed by using the method shown below. ( ) for V2 output trim Product Options Table Option Negative remote ON/OFF logic, 0.20” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length Negative remote ON/OFF logic, 0.11” pin length Positive remote ON/OFF logic, 0.20” pin length L K P S M Suffix 9(6) Trim Up RU 10(7) Trim Down RD Positive remote ON/OFF logic, 0.145” pin length Positive remote ON/OFF logic, 0.11” pin length 10(7) 8(5) Example: RP100-483.305I/N 200 July-2006 www.recom-international.com