RP12-2405DAW

Features Regulated Converters ● ● ● ● ● ● ● ● 4:1 Wide Input Voltage Range 12 Watts Regulated Output Power 1.6kVDC Isolation Over Current and Over Voltage Protection Five-Sided Shield No Derating to 61°C Standard DIP24 Pinning Efficiency to 88% POWERLINE DC/DC-Converter Selection Guide 24V and 48V Wide Input Types Part Number DIP24 (SMD) RP12-243.3SAW** RP12-2405SAW** RP12-2412SAW** RP12-2415SAW** RP12-483.3SAW** RP12-4805SAW** RP12-4812SAW** RP12-4815SAW** RP12-2405DAW** RP12-2412DAW** RP12-2415DAW** RP12-4805DAW** RP12-4812DAW** RP12-4815DAW** Input Range VDC 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 9-36 9-36 9-36 18-75 18-75 18-75 Output Voltage VDC 3.3 5.1 12 15 3.3 5.1 12 15 ±5 ±12 ±15 ±5 ±12 ±15 Output Current mA 3500 2400 1000 800 3500 2400 1000 800 ±1200 ±500 ±400 ±1200 ±500 ±400 Input (4,5) Current mA 55/602 55/614 25/610 25/610 20/301 20/307 13/302 13/298 20/625 25/610 25/610 10/309 13/301 13/301 Efficiency(6)Capacitive(7) Load max. % µF 84 87 86 86 84 87 87 88 84 86 86 85 87 87 2000 2000 430 300 2000 2000 430 300 ±1250 ±200 ±120 ±1250 ±200 ±120 RP12S_DAW Series 12 Watt DIP24 & SMD, Single & Dual Output UL-60950-1 Certified ** add Suffix SMD for SMD package Derating Graph (Ambient Temperature) RP12-4805SAW 125 100 75 Output Power (%) 50 25 0 -40 -25 -10 0 75Vin Natural Convection Nom Vin 50 60 70 80 90 100 110 Ambient Temperature Range (°C) 65 Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range Input Filter Input Surge Voltage (100 ms max.) Input Reflected Ripple (nominal Vin and full load) 24V Input 48V Input 24V nominal input 48V nominal input 9-36VDC 18-75VDC Pi Type 50VDC 100VDC 20mAp-p continued on next page www.recom-international.com 14-February-2007 233 POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see note 1) Remote OFF input current Output Power Output Voltage Accuracy (full Load and nominal Vin) Minimum Load Line Regulation (low line, high line at full load) Load Regulation (0% to 100% full load) Cross Regulation Dual Output (asymmetrical load 25%/100% full load) Ripple and Noise (20MHz bandwith) Temperature Coefficient Transient Response (25% load step change) Input Voltage Variation, dv/dt Over Load Protection (% of full load at nominal Vin) Overvoltage Protection (Single) Undervoltage Protection Short Circuit Protection Efficiency Isolation Voltage Isolation Resistance Isolation Capacitance Operating Frequency Operating Temperature Range 24V Input 48V Input Single Dual DC-DC ON DC-DC OFF Nominal input RP12-S_DAW Series 450ms typ. Open or 3.0V < Vr < 12V Short or 0V < Vr < 1.2V 2.5mA 12W max. ±1.2% 0% ±0.2% ±0.5% ±1% ±5% 85mVp-p ±0.02%/°C max. 250µs complies with ETS300 132, part 4.4 5V/ms 150% typ Zener Diode Clamp DC-DC ON = 9VDC, DC-DC OFF = 8VDC DC-DC ON = 18VDC, DC-DC OFF = 16VDC Continuous, automatic recovery see „Selection Guide“ table In to Out and I/O to case 1600VDC min. 10 GΩ min. 1500pF max. 5.1, 12, 15, ±12, ±15V 3.3, ±5V with derating 400kHz typ. -40°C to +65°C -40°C to +61°C -40°C to +105°C +105°C -55°C to +125°C Natural convection 20°C/Watt Nickel plated copper Non-conductive black plastic DIP SMD EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Epoxy (UL94-V0) 18g 20g Class A Class A Perf. Critera B Perf. Critera A Perf. Critera B Perf. Critera B Perf. Critera A MIL-STD-810D 10-55Hz, 2G, 30 Min. along X, Y and Z 5% to 95% RH Bellcore-TR-NWT-000332 14-February-2007 2350 x 103 hours www.recom-international.com Maximum Case Temperature Storage Temperature Range Thermal Impedance Case Material Base Material Potting Material Weight Conducted Emissions (see note 3) Radiated Emissions (see note 3) ESD Radiated Immunity Fast Transient Surge Conducted Immunity Thermal Shock Vibration Relative Humidity MTBF (see note 2) 234 POWERLINE DC/DC-Converter Notes : 1. 2. 3. 4. 5. 6. 7. RP12-S_DAW Series The ON/OFF control pin voltage is referenced to negative input. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). Requires external filter to meet EN55022 Class A Typical value at nominal input voltage and no load. Maximum value at nominal input voltage and full load Typical value at nominal input voltage and full load. Test by minimum Vin and constant resistor load. Package Style and Pinning (mm) DIP24 Package Style 31.80 20.30 3rd angle projection 10.20 3.8 2 20.30 5.10 15.20 Pin Connections Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin 2.54 0.25 x 0.50 Rectangular Pin 9 11 123 Bottom View 23 22 Pin Pitch Tolerance ±0.35 mm 16 14 SMD Package Style 32.00 31.40 11.20 10.90 3.81 6.35 21.30 25.40 20.30 SMD Package Style Same spec. as the original DIP spec. and pin definition, excl. of the SMD type pin. 2.54 Pin Connections Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin Others NC NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin NC Pin area 0.1 x 0.50 12345 0.50 9 10 11 12 2.54 1.60 2.40 23.40 Bottom View 24 23 22 21 20 16 15 14 13 26.54 24.14 1 Top View Pin Pitch Tolerance ±0.35 mm 11 x 2.54 27.94 www.recom-international.com 14-February-2007 235