RP12-2412SA

Features ● ● ● ● ● ● ● ● 2:1 Wide Input Voltage Range 12 Watts Output Power 1.6kVDC Isolation UL Certified Over Current Protection Five-Sided Shield Standard DIP24 and SMD-Pinning Efficiency to 88% POWERLINE DC/DC-Converter RP12S_DA Series 12 Watt DIP24 & SMD, Single & Dual Output Selection Guide 5V, 12V, 24V and 48V Input Types Part Number DIP24 (SMD) RP12-122.5SA** RP12-123.3SA** RP12-1205SA** RP12-1212SA** RP12-1215SA** RP12-242.5SA** RP12-243.3SA** RP12-2405SA** RP12-2412SA** RP12-2415SA** RP12-482.5SA** RP12-483.3SA** RP12-4805SA** RP12-4812SA** RP12-4815SA** RP12-1205DA** RP12-1212DA** RP12-1215DA** RP12-2405DA** RP12-2412DA** RP12-2415DA** RP12-4805DA** RP12-4812DA** RP12-4815DA** Input Range VDC 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 9-18 9-18 9-18 18-36 18-36 18-36 36-75 36-75 36-75 Output Voltage VDC 2.5 3.3 5 12 15 2.5 3.3 5 12 15 2.5 3.3 5 12 15 ±5 ±12 ±15 ±5 ±12 ±15 ±5 ±12 ±15 Output Current mA 3500 3500 2400 1000 800 3500 3500 2400 1000 800 3500 3500 2400 1000 800 ±1200 ±500 ±400 ±1200 ±500 ±400 ±1200 ±500 ±400 Input (4) Current mA 1687 1646 1606 1606 1606 843 823 803 803 803 422 411 401 401 401 1687 1626 1626 843 813 813 422 406 406 Efficiency(5) Capacitive(6) Load max. % µF 82 84 86 86 86 83 85 87 87 87 83 85 87 87 87 82 87 87 83 88 88 83 88 88 2000 2000 2000 430 300 2000 2000 2000 430 300 2000 2000 2000 430 300 ±1250 ±200 ±120 ±1250 ±200 ±120 ±1250 ±200 ±120 UL-60950-1 Certified ** add Suffix SMD for SMD package www.recom-international.com 14-February-2007 229 POWERLINE DC/DC-Converter RP12-S_DA Series RP12-4805SA 125 100 75 Output Power (%) 50 25 0 -40 -25 -10 0 Derating-Graph (Ambient Temperature) Natural Convection 50 60 70 80 90 100 Ambient Temperature Range (°C) 63 Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at info@recom-development.at Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 24V nominal input 48V nominal input 12V Input DC-DC ON DC-DC OFF 24V Input DC-DC ON DC-DC OFF 48V Input DC-DC ON DC-DC OFF 9-18VDC 18-36VDC 36-75VDC 9VDC 8VDC 18VDC 16VDC 36VDC 33VDC Pi Type (Complies with ETS300 132 part 4.4) 12V Input 24V Input 48V Input 5V/ms max. 36VDC 50VDC 100VDC 20mAp-p 600ms typ. DC-DC ON DC-DC OFF Nominal input Open or 3.0V < Vr < 12V Short or 0V < Vr < 1.2V 2.5mA 12W max. ±1.2% 10% of full load continued on next page Under Voltage Lockout Input Filter Input Voltage Variation dv/dt Input Surge Voltage (100 ms max.) Input Reflected Ripple (nominal Vin and full load) (see Note 3) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see Note 7) Remote OFF input curren Output Power Output Voltage Accuracy (full Load and nominal Vin) Minimum Load (see Note 1) 230 14-February-2007 www.recom-international.com POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Line Regulation (low line, high line at full load) Single Dual Load Regulation (25% to 100% full load) Single Dual (only 2.5Vout) RP12-S_DA Series ±0.2% ±0.5% ±0.5% ±1% ±1.5% ±5% 85mVp-p ±0.02%/°C max. 300µs 2.5V 3.3V 5V 12V 15V 3.9V 3.9V 6.2V 15V 18V 150% typ Continuous, automatic recovery see „Selection Guide“ table In to out I/O to case 1600VDC min. 1600VDC min. 1 GΩ min. 1200pF max. 400kHz typ. -40°C to +85°C(with derating) +100°C -55°C to +105°C Natural convection 20°C/Watt MIL-STD-810D 10-55Hz, 2G, 30 Min. along X, Y and Z 5% to 95% RH Nickel plated copper Non-conductive black plastic Epoxy (UL94-V0) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 DIP SMD Class A Class A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 18g 20g 31.8 x 20.3 x 10.2mm 2750 x 103 hours Cross Regulation (asymmetrical load 25%/100% full load) Ripple and Noise (20MHz bandwith) Temperature Coefficient Transient Response (25% load step change) Over Voltage Protection Zener diode clamp (only single) Over Load Protection (% of full load at nominal Vin) Short Circuit Protection Efficiency Isolation Voltage Isolation Resistance Isolation Capacitance Operating Frequency Operating Temperature Range Maximum Case Temperature Storage Temperature Range Thermal Impedance Thermal Shock Vibration Relative Humidity Case Material Base Material Potting Material Conducted Emissions (see Note 8) Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Weight Dimensions MTBF (see Note 2) www.recom-international.com 14-February-2007 231 POWERLINE DC/DC-Converter Notes : RP12-S_DA Series 1. The RP12 series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Simulated source impedance of 12µH. 12µH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control pin voltage is referenced to negative input. 8. See application notes for EMI-filtering. Package Style and Pinning (mm) DIP24 Package Style 31.80 20.30 3rd angle projection 10.20 3.8 2 20.30 5.10 15.20 Pin Connections Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin 2.54 0.25 x 0.50 Rectangular Pin 9 11 123 Bottom View 23 22 16 14 Pin Pitch Tolerance ±0.35 mm SMD Package Style 32.00 31.40 11.20 10.90 3.81 6.35 21.30 25.40 20.30 SMD Package Style Same spec. as the original DIP spec. and pin definition, excl. of the SMD type pin. 2.54 Pin Connections Pin # Single 1 ON/OFF 2 -Vin 3 -Vin 9 NC 11 NC 14 +Vout 16 -Vout 22 +Vin 23 +Vin Others NC NC = No Connection Dual ON/OFF -Vin -Vin Com -Vout +Vout Com +Vin +Vin NC Pin area 0.1 x 0.50 12345 0.50 9 10 11 12 2.54 1.60 2.40 23.40 Bottom View 24 23 22 21 20 16 15 14 13 26.54 24.14 1 Top View Pin Pitch Tolerance ±0.35 mm 11 x 2.54 27.94 232 14-February-2007 www.recom-international.com