RP20-243.3SEW_06

Features ● ● ● ● ● ● ● ● 4:1 Wide Input Voltage Range 20 Watts Output Power 1.6kVDC Isolation UL 60950 Pending Fixed Operating Frequency Six-Sided Continuous Shield Standard 50.8 x40.6x10.2mm Package Efficiency to 84% POWERLINE DC/DC-Converter RP20S_DEW Series 20 Watt Single & Dual Output Selection Guide 24V and 48V Input Types Part Number Input Range VDC 9-36 9-36 9-36 9-36 18-75 18-75 18-75 18-75 9-36 9-36 9-36 18-75 18-75 18-75 Output Voltage VDC 3.3 5 12 15 3.3 5 12 15 ±5 ±12 ±15 ±5 ±12 ±15 Output Current mA 4000 4000 1670 1330 4000 4000 1670 1330 ±2000 ±833 ±666 ±2000 ±833 ±666 Input (4) Current mA 764 1111 1082 1082 377 548 541 541 1111 1082 1068 556 527 521 Efficiency(5) Capacitive(6) Load max. % µF 76 79 81 81 77 80 81 81 79 81 82 79 83 84 13000 6800 2200 755 13000 6800 2200 755 ±3400 ±680 ±450 ±3400 ±680 ±450 RP20-243.3SEW RP20-2405SEW RP20-2412SEW RP20-2415SEW RP20-483.3SEW RP20-4805SEW RP20-4812SEW RP20-4815SEW RP20-2405DEW RP20-2412DEW RP20-2415DEW RP20-4805DEW RP20-4812DEW RP20-4815DEW www.recom-international.com July-2006 251 POWERLINE DC/DC-Converter Derating-Graph (Ambient Temperature) 125 100 75 Output Power (%) 50 25 50 60 70 80 90 100 Ambient Temperature Range (°C) 56°C 0 -40 -25 -10 0 RP20-S_DEW Series RP20-2412SEW 125 100 RP20-2412SEW With Heat Sink Output Power (%) Natural Convection 75 50 25 Natural Convection 0 -40 -25 -10 0 50 60 70 80 90 100 65°C Ambient Temperature Range (°C) RP20-2412DEW 125 100 75 Output Power (%) 50 25 50 60 70 80 90 100 Ambient Temperature Range (°C) 64°C 0 -40 -25 -10 0 125 RP20-2412DEW With Heat Sink 100 Output Power (%) Natural Convection 75 50 25 Natural Convection 0 -40 -25 -10 0 50 60 70 80 90 100 71°C Ambient Temperature Range (°C) Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at info@recom-development.at Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range Input Filter Input Surge Voltage (100 ms max.) Input Reflected Ripple (nominal Vin and full load) (see Note 3) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see Note 7) ( Positive logic ) Remote OFF input current Output Power Output Voltage Accuracy (full Load and nominal Vin) Voltage Adjustability Line Regulation (low line, high line at full load) DC-DC ON DC-DC OFF Nominal input Single & Dual Auxiliary Single (W) Dual (W) Auxiliary 24V nominal input 48V nominal input 24V Input 48V Input 9-36VDC 18-75VDC Pi Type 50VDC 100VDC 25mAp-p 20ms typ. Open or 3.5V < Vr < 12V Short or 0V < Vr < 1.2V 20mA 20W max. ±2% ±5% ±10% ±0.2% ±0.5% ±5% 10% of full load continued on next page 252 July-2006 www.recom-international.com Minimum Load (see Note 1) POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Line Regulation (low line, high line at full load) Single (W) Dual (W) Auxiliary Single Dual Auxiliary Dual Auxiliary Single Dual Auxiliary RP20-S_DEW Series ±0.2% ±0.5% ±5% ±0.5% ±3% ±5% ±5% ±5% 75mVp-p 100mVp-p 1% of Vout ±0.02%/°C max. 3.3V 5V 12V 15V 500µs 3.9V 6.2V 15V 18V Hiccup, automatic recovery see „Selection Guide“ table 1600VDC min. 1 GΩ min. 300pF max. 300kHz typ. EN60950 -40°C to +85°C(with derating) +100°C Natural convection Natural convection with Heat Sink -55°C to +105°C 10°C/Watt 8.24°C/Watt MIL-STD-810D 10-55Hz, 2G, 30 Min. along X, Y and Z 5% to 95% RH Nickel plated copper Non-conductive black plastic Epoxy (UL94-V0) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 48g 50.8 x 40.6 x 10.2mm 1928 x 103 hours Load Regulation (25% to 100% full load) Cross Regulation (see Note 9) Ripple and Noise (20MHz bandwith) Temperature Coefficient Transient Response (25% load step change) Over Voltage Protection Zener diode clamp (only single) Short Circuit Protection Efficiency Isolation Voltage Isolation Resistance Isolation Capacitance Operating Frequency Approved to Safety Standards Operating Temperature Range Maximum Case Temperature Storage Temperature Range Thermal Impedance (see Note 8) Thermal Shock Vibration Relative Humidity Case Material Base Material Potting Material Conducted Emissions (see Note 10) Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Weight Dimensions MTBF (see note 2) www.recom-international.com July-2006 253 POWERLINE DC/DC-Converter Notes : RP20-S_DEW Series 1. The RP20 series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Simulated source impedance of 12µH. 12µH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control voltage is reference to negative input. 8. Heat sink is optional and P/N: 7G-0011A. Operation temperature range please see curve. 9. Cross regulation: Dual output—Asymmetrical load 25% to 100% full load Triple output – 3.3V / 5V 100% load and one of auxiliary 100% load, other auxiliary load change from 25% to 100% load 10.See application notes for EMI-filtering. Package Style and Pinning (mm) 3rd angle projection 50.10 10.20 dia. 1.0 5.6 40.60 45.70 Pin Connections Pin # 1 2 4 5 6 7 8 Single +Vin -Vin CTRL No Pin +Vout -Vout Trim Dual +Vin -Vin CTRL +Vout Com -Vout Trim 5 17.80 Bottom View 5.10 15.20 1 2 10.20 6 12.70 Pin Pitch Tolerance ±0.35 mm 7 4 10.20 8 17.80 External Output Trimming Output can be externally trimmed by using the method shown below. ( ) for dual output trim 7(7) Trim Up RU 8(8) Trim Down RD 8(8) 6(5) 254 July-2006 www.recom-international.com