RP30-1212SE

Features ● ● ● ● ● ● ● ● ● 2:1 Wide Input Voltage Range 30 Watts Output Power 1.6kVDC Isolation UL Certified Fixed Operating Frequency Six-Sided Continuous Shield International Safety Standard Approvals Standard 50.8 x40.6x10.2mm Package Efficiency to 90% POWERLINE DC/DC-Converter RP30S_DE Series 30 Watt Single & Dual Output Selection Guide 12V, 24V and 48V Input Types Part Number Input Range VDC RP30-121.5SE RP30-121.8SE RP30-122.5SE RP30-123.3SE RP30-1205SE RP30-1212SE RP30-1215SE RP30-241.5SE RP30-241.8SE RP30-242.5SE RP30-243.3SE RP30-2405SE RP30-2412SE RP30-2415SE RP30-481.5SE RP30-481.8SE RP30-482.5SE RP30-483.3SE RP30-4805SE RP30-4812SE RP30-4815SE RP30-1212DE RP30-1215DE RP30-2412DE RP30-2415DE RP30-4812DE RP30-4815DE 9-18 9-18 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 36-75 36-75 9-18 9-18 18-36 18-36 36-75 36-75 Output Voltage VDC 1.5 1.8 2.5 3.3 5 12 15 1.5 1.8 2.5 3.3 5 12 15 1.5 1.8 2.5 3.3 5 12 15 ±12 ±15 ±12 ±15 ±12 ±15 Output Current mA 6000 6000 6000 6000 6000 2500 2000 6000 6000 6000 6000 6000 2500 2000 6000 6000 6000 6000 6000 2500 2000 ±1250 ±1000 ±1250 ±1000 ±1250 ±1000 Input (4) Current mA 1014 1169 1582 2037 3012 2976 2976 493 580 780 1010 1490 1470 1470 244 290 390 500 740 730 730 3012 3012 1488 1488 744 744 Efficiency(5) Capacitive(6) % 78 81 83 85 87 88 88 80 82 84 86 88 89 89 81 83 85 87 89 90 90 87 87 88 88 88 88 Load max. µF 85800 65000 33000 19500 10200 3240 1100 85800 65000 33000 19500 10200 3300 1100 85800 65000 33000 19500 10200 3300 1100 ±1020 ±675 ±1020 ±675 ±1020 ±675 UL-60950-1 Certified Description The E-series of these DC/DC-converters is designed to meet UL 60950. This makes them ideal for all telecom and safety applications where approved isolation is required. They are also designed to meet UL 1950 and CSA 950 standards. 262 July-2006 www.recom-international.com POWERLINE DC/DC-Converter RP30-S_DE Series RP30-4805SE With Heat Sink 125 100 Derating-Graph (Ambient Temperature) RP30-4805SE 125 100 75 Output Power (%) 50 25 0 -40 -25 -10 0 50 60 70 80 90 100 62°C Output Power (%) Natural Convection 75 50 25 Natural Convection 0 -40 -25 -10 0 50 60 70 Ambient Temperature Range (°C) Ambient Temperature Range (°C) 80 90 100 71°C Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at info@recom-development.at Typical Characteristics RP30-4805SE Efficiency VS Input Voltage 93 92 91 90 89 88 87 86 85 84 83 82 92 90 89 88 87 86 85 84 80 78 76 74 RP30-4805SE Efficiency VS Output Load Efficiency (%) 36 40 45 50 55 60 65 70 75 Efficiency (%) 1 2 3 4 5 6 Intput Voltage (V) Output Load (A) Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 24V nominal input 48V nominal input 12V input DC-DC ON DC-DC OFF 24V input DC-DC ON DC-DC OFF 48V input DC-DC ON DC-DC OFF 9-18VDC 18-36VDC 36-75VDC 9VDC 8VDC 17.8VDC 16VDC 36VDC 33VDC L-C Type (Complies with ETS300 132 part 4.4) 12V Input 24V Input 48V Input 5V/ms max 36VDC 50VDC 100VDC 30mAp-p DC-DC ON DC-DC OFF Nominal input 25ms typ. Open or 3.0V < Vr < 12V Short or 0V < Vr < 1.2V 2.5mA continued on next page www.recom-international.com July-2006 263 Under Voltage Lockout Input Filter (see Note 1) Input Voltage Variation dv/dt Input Surge Voltage (100 ms max.) Input Reflected Ripple (nominal Vin and full load) (see Note 3) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see Note 7) Remote OFF input current POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Output Power Output Voltage Accuracy (full Load and nominal Vin) Voltage Adjustability Minimum Load Line Regulation (low line, high line at full load) Load Regulation (25% to 100% full load) Cross Regulation Ripple and Noise (20MHz bandwith) (Measured with a 1004pF/50V MLCC) Temperature Coefficient Transient Response (25% load step change) Over Voltage Protection Zener diode clamp (only single) 1.5, 1.8, 2.5, 3.3V 5V 12V 15V Single & Dual Single Dual Single Dual RP30-S_DE Series 30W max. ±1% ±10% 0% ±0.2% ±0.5% ±0.5% ±1% ±5% 50mVp-p 75mVp-p 100mVp-p ±0.02%/°C max. 300µs 3.9V 6.2V 15V 18V 150% typ Hiccup, automatic recovery see „Selection Guide“ table 1600VDC min. 1 GΩ min. 1000pF max. 300kHz typ. UL 1950, EN60950 -40°C to +85°C(with derating) +100°C -55°C to +105°C Natural convection Natural convection with Heat Sink 115°C typ. 10°C/Watt 8.24°C/Watt MIL-STD-810D 10-55Hz, 2G, 30 Min. along X, Y and Z 5% to 95% RH Nickel plated copper Non-conductive black plastic Epoxy (UL94-V0) EN55022 EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Class A Class A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 continued on next page Single 1.5, 1.8, 2.5, 3.3, 5V Single 12, 15V Dual 5, 12, 15V Over Load Protection (% of full load at nominal Vin) Short Circuit Protection Efficiency Isolation Voltage Isolation Resistance Isolation Capacitance Operating Frequency Approved to Safety Standards Operating Temperature Range Maximum Case Temperature Storage Temperature Range Over Temperature Protection Thermal Impedance (see Note 8) Thermal Shock Vibration Relative Humidity Case Material Base Material Potting Material Conducted Emissions (see Note 9) Radiated Emissions ESD Radiated Immunity Fast Transient Surge Conducted Immunity 264 July-2006 www.recom-international.com POWERLINE DC/DC-Converter Specifications (typical at nominal input and 25°C unless otherwise noted) Weight Dimensions MTBF (see Note 2) RP30-S_DE Series 48g 50.8 x 40.6 x 10.2mm 1535 x 103 hours Notes : 1. An external filter capacitor is required for normal operation. The capacitor should be capable of handing 1A ripple current for 48V/24V models. RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90m Ω. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Simulated source impedance of 12µH. 12µH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control pin voltage is referenced to negative input 8. Heat sink is optional and P/N: 7G-0011A. 9. See application notes for EMI-filtering. Package Style and Pinning (mm) 3rd angle projection 50.80 10.20 dia. 1.0 5.6 40.60 Pin Connections Pin # 1 2 4 5 6 7 8 Single +Vin -Vin CTRL No Pin +Vout -Vout Trim Dual +Vin -Vin CTRL +Vout Com -Vout Trim 45.70 5 17.80 Pin Pitch Tolerance ±0.35 mm Bottom View 5.10 15.20 1 2 10.20 6 12.70 External Output Trimming 10.20 17.80 7 4 Output can be externally trimmed by using the method shown below. ( ) for dual output trim 8 7(7) Trim Up RU 8(8) Trim Down RD 8(8) 6(5) www.recom-international.com July-2006 265