RP30-2415DE-HC

CONVER T M CONVER y T S S REACH compliant CO 10 from 10 PL U D IA N T PRO O 3 arrant R R M C M TS M YEA R E O E C RoHS 2 + compliant CO Part Number Input Output Output Input (1) Efficiency (1) Max. Capacitive Voltage Range Voltage Current Current typ. Load (2) [VDC] [VDC] [mA] [mA] [%] [µF] RP30-123.3SE (3) 9-18 3.3 6000 1941 85 19500 RP30-1205SE (3) 9-18 5 6000 2874 87 10200 RP30-1212SE (3) 9-18 12 2500 2841 88 3240 RP30-1215SE (3) 9-18 15 2000 2841 88 1100 RP30-243.3SE (3) 18-36 3.3 6000 959 86 19500 RP30-2405SE (3) 18-36 5 6000 1420 88 10200 RP30-2412SE (3) 18-36 12 2500 1404 89 3240 RP30-2415SE (3) 18-36 15 2000 1404 89 1100 RP30-483.3SE (3) 36-75 3.3 6000 474 87 19500 RP30-4805SE (3) 36-75 5 6000 702 89 10200 RP30-4812SE (3) 36-75 12 2500 694 90 3240 RP30-4815SE (3) 36-75 15 2000 694 90 1100 RP30-1212DE (3) 9-18 ±12 ±1250 2874 87 ±1020 RP30-1215DE (3) 9-18 ±15 ±1000 2874 87 ±675 RP30-2412DE (3) 18-36 ±12 ±1250 1420 88 ±1020 RP30-2415DE (3) 18-36 ±15 ±1000 1420 88 ±675 RP30-4812DE (3) 36-75 ±12 ±1250 710 88 ±1020 RP30-4815DE (3) 36-75 ±15 ±1000 710 88 ±675 C Selection Guide 30 Watt 2’’ x 1.6’’ Single and Dual Output w The RP30-E series DC/DC converters are certified to UL 60950-1 and cUL 60950-1. This makes them ideal for all telecom and industrial applications where approved safety standards are required. The industry standard 2” x 1.6” package meets military standards for thermal shock and vibration tolerance RP30-E RE Description DC/DC Converter TS 2:1 input voltage range 1.6kVDC isolation UL certified Efficiency up to 90% Six-sided continuous shield Available as power module (RPM30-E) C Regulated Converter • • • • • • RE Features PL U D IA N T PRO E196683 UL60950-1 certified EN55032 compliant Notes: Note1: Maximum values at nominal input voltage and full load Note2: Max. Cap load is tested at minimum input and constant resistive load Model Numbering RP30-__ __ _E- _ nom. Input Voltage “Package (3)” Output Voltage Single or Dual Notes: Note3: add suffix “-HC” for premounted Heat-sink with clips Ordering Examples RP30-2405SE = 24V Input, 5V Output, Single RP30-4812DE-HC = 48V Input, ±12V Output, Dual, Heat-sink premounted www.recom-power.com REV.: 4/2020 PD-1 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) BASIC CHARACTERISTICS Parameter Condition Internal Input Filter Min. Typ. Max. LC Type (4) Under Voltage Lockout (UVLO) 36VDC 50VDC 100VDC 100ms max. nom. Vin = 12VDC nom. Vin = 24VDC nom. Vin = 48VDC nom. Vin = 12VDC DC-DC ON DC-DC OFF 8VDC nom. Vin = 24VDC DC-DC ON DC-DC OFF 16VDC nom. Vin = 48VDC DC-DC ON DC-DC OFF 33VDC Input Surge Voltage 9VDC 17.8VDC 36VDC refer to „OUTPUT VOLTAGE TRIMMING“ Output Voltage Trimming 18VDC 36VDC 75VDC 12VDC 24VDC 48VDC 9VDC 18VDC 36VDC nom. Vin = 12VDC nom. Vin = 24VDC nom. Vin = 48VDC Input Voltage Range -10% Minimum Load +10% 0% Power up ON/OFF CTRL Start-up Time 25ms 25ms ON/OFF CTRL (5) refer to “ON/OFF CTRL” Positive Logic DC-DC ON DC-DC OFF Input Current of CTRL pin drive current ICTRL Standby Current DC-DC OFF IIn Open or 3.0VDC < VCTRL< 12VDC Short or 0VDC < VCTRL< 1.2VDC -0.5mA +0.5mA 2.5mA Internal Operating Frequency 270kHz measured at 20MHz BW with a 0.1µF/50V MLCC Output Ripple and Noise Input Reflected Ripple Current Notes: Note4: Note5: Note6: 300kHz 3.3Vout, 5Vout 12Vout, 15Vout 50mVp-p 75mVp-p ±12Vout, ±15Vout 100mVp-p 330kHz 30mAp-p (6) An external filter capacitor is required for normal operation. The capacitor should be capable of handling 1A ripple current for 48V/24V models. RECOM suggest: Nippon chemi-con KY series, 220μF/100V, ESR 90mΩ The pin voltage is referenced to -Vin pin Simulated source impedance of 12μH. 12μH inductor in series with +Vin RP30-1205SE Efficiency vs. Output Current Efficiency vs. Input Voltage 90 85 80 75 Efficiency [%] Efficiency [%] 95 90 85 70 65 60 55 9Vin 12Vin 18Vin 50 45 40 10 20 30 40 50 60 70 80 90 80 75 70 65 60 100 Output Current [%] 9 10 11 12 13 14 15 16 17 18 Input Voltage [VDC] continued on next page www.recom-power.com REV.: 4/2020 PD-2 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) RP30-2405SE Efficiency vs. Output Current 95 90 90 80 85 Efficiency [%] Efficiency [%] 85 75 70 65 60 55 18Vin 24Vin 36Vin 50 45 40 Efficiency vs. Input Voltage 95 10 20 30 40 50 60 70 80 80 75 70 65 90 60 100 18 20 22 Output Current [%] 24 26 28 30 32 34 36 72 75 Input Voltage [VDC] RP30-4805SE Efficiency vs. Output Current 95 90 90 80 85 Efficiency [%] Efficiency [%] 85 75 70 65 60 55 36Vin 48Vin 75Vin 50 45 40 Efficiency vs. Input Voltage 95 10 20 30 40 50 60 70 80 80 75 70 65 90 60 100 36 40 Output Current [%] 44 48 52 56 60 64 68 Input Voltage [VDC] OUTPUT VOLTAGE TRIMMING Output Voltage Trimming Some single/dual output Powerline converters offer the feature of trimming the output voltage over a certain range around the nominal value by using external trim resistors. No general equation can be given for calculating the trim resistors, but the following trimtables give typical values for choosing these trimming resistors. If voltages between the given trim points are required, extrapolate between the two nearest given values to work out the resistor required or use a variable resistor to set the output voltage. Output can be externally trimmed by using the method shown below. Trim up Trim down Trim -Vout RD RU +Vout Trim RP30-xx3.3SE Trim up 1 2 3 4 5 6 7 8 9 10 [%] Vout = 3.333 3.366 3.399 3.432 3.465 3.498 3.531 3.564 3.597 3.63 [VDC] RU = 57.93 26.16 15.58 10.28 7.11 4.99 3.48 2.34 1.46 0.75 [kW] 1 2 3 4 5 6 7 8 9 10 [%] Trim down Vout = 3.267 3.234 3.201 3.168 3.135 3.102 3.069 3.036 3.003 2.97 [VDC] RD = 69.47 31.23 18.49 12.12 8.29 5.74 3.92 2.56 1.50 0.65 [kW] continued on next page www.recom-power.com REV.: 4/2020 PD-3 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) RP30-xx05SE Trim up 1 2 3 4 5 6 7 8 9 10 [%] Vout = 5.05 5.10 5.15 5.20 5.25 5.30 5.35 5.4 5.45 5.50 [VDC] RU = 36.57 16.58 9.92 6.58 4.59 3.25 2.30 1.59 1.03 0.59 [kW] 1 2 3 4 5 6 7 8 9 10 [%] Trim down Vout = 4.95 4.90 4.85 4.80 4.75 4.70 4.65 4.60 4.55 4.50 [VDC] RD = 45.53 20.61 12.31 8.15 5.66 4.00 2.81 1.92 1.23 0.68 [kW] RP30-xx12SE Trim up 1 2 3 4 5 6 7 8 9 10 [%] Vout = 12.12 12.24 12.36 12.48 12.60 12.72 12.84 12.96 13.08 13.20 [VDC] RU = 367.91 165.95 98.64 64.98 44.78 31.32 21.70 14.49 8.88 4.39 [kW] 1 2 3 4 5 6 7 8 9 10 [%] Trim down Vout = 11.88 11.76 11.64 11.52 11.40 11.28 11.16 11.04 10.92 10.8 [VDC] RD = 460.99 207.95 123.60 81.42 56.12 39.25 27.20 18.16 11.13 5.51 [kW] 2 3 4 5 6 7 8 9 10 [%] RP30-xx15SE Trim up 1 Vout = 15.15 15.3 15.45 15.60 15.75 15.90 16.05 16.20 16.35 16.50 [VDC] RU = 404.18 180.59 106.06 68.80 46.44 31.53 20.88 12.90 6.69 1.72 [kW] 1 2 3 4 5 6 7 8 9 10 [%] Trim down Vout = 14.85 14.70 14.55 14.40 14.25 14.10 13.95 13.80 13.65 13.50 [VDC] RD = 499.82 223.41 131.27 85.20 57.56 39.14 25.97 16.10 8.42 2.282 [kW] 2 3 4 5 6 7 8 9 10 [%] RP30-xx12DE Trim up 1 Vout = 24.24 24.48 24.72 24.96 25.20 25.44 25.68 25.92 26.16 26.40 [VDC] RU = 218.21 98.10 58.07 38.05 26.04 18.03 12.32 8.03 4.69 2.02 [kW] 1 2 3 4 5 6 7 8 9 10 [%] Vout = 23.76 23.52 23.28 23.04 22.80 22.56 22.32 22.08 21.84 21.6 [VDC] RD = 273.44 123.02 72.87 47.80 32.76 22.73 15.57 10.20 6.02 2.67 [kW] 2 3 4 5 6 7 8 9 10 [%] Trim down RP30-xx15DE Trim up 1 Vout = 30.30 30.60 30.90 31.20 31.50 31.80 32.10 32.40 32.70 33.00 [VDC] RU = 268.29 120.64 71.43 46.82 32.06 22.21 15.10 9.91 5.81 2.53 [kW] 1 2 3 4 5 6 7 8 9 10 [%] Vout = 29.70 29.40 29.10 28.80 28.50 28.20 27.90 27.60 27.30 27.00 [VDC] RD = 337.71 152.02 90.13 59.18 40.61 28.23 19.39 12.76 7.60 3.47 [kW] Trim down www.recom-power.com REV.: 4/2020 PD-4 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) ON/OFF CTRL +Vin VCTRL IIN +Vin ICTRL +Vout +Vout CTRL -Vin -Vin Positve Logic -Vout DC-DC ON DC-DC OFF Open or 3.0VDC < VCTRL < 12VDC Short or 0VDC < VCTRL < 1.2VDC -Vout REGULATIONS Parameter Condition Value Output Accuracy ±1.0% Line Regulation low line to high line, full load Single Dual ±0.2% ±0.5% Load Regulation 0% to 100% load Single Dual ±0.5% ±1.0% Cross Regulation asymmetrical 25%100% load Transient Response Recovery Time 25% load step change ±5.0% 300μs typ. PROTECTIONS Parameter Condition Value Short Circuit Protection (SCP) continuous, automatic recovery Over Voltage Protection (OVP) zener diode clamp Over Load Protection (OLP) Over Temperature Protection (OTP) Isolation Voltage (7) Isolation Resistance 3.3Vout 5Vout 12Vout 15Vout % of Iout rated 3.9VDC 6.2VDC 15VDC 18VDC 150% typ. 115°C typ. I/P to O/P I/P to O/P to case Viso= 500VDC Isolation Capacitance 1.6kVDC/ 1 minute 1.6kVDC/ 1 minute 1GΩ min. 1000pF max. Notes: Note7: For repeat Hi-Pot testing, reduce the time and/or the test voltage Note8: This power module is not internally fused. An input line fuse must always be used ENVIRONMENTAL Parameter Operating Temperature Range Condition without derating with derating Maximum Case Temperature Operating Humidity ±0.02%/K max. @ natural convection 0.1m/s without heat-sink with heat-sink non-condensing Thermal Shock 10K/W 8.24K/W 5% - 95% RH according to MIL-STD-810F Vibration MTBF -40°C to +70°C -40°C to +100°C +100°C Temperature Coefficient Thermal Impedance Value according to MIL-STD-810F MIL-HDBK-217F, G.B Bellcore TR-NWT-000332 (9) 1283 x 103 hours 1535 x 103 hours continued on next page www.recom-power.com REV.: 4/2020 PD-5 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) Derating Graph (10) RP30-483.3SE RP30-483.3SE-HC 80 80 Output Power [%] 100 Output Power [%] 100 60 40 20 0 -40 -20 0 20 40 60 70 80 60 40 20 0 -40 100 120 Ambient Temperature [°C] -20 0 20 40 60 80 76 100 120 Ambient Temperature [°C] Notes: Note9: BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment) Note10: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact RECOM Techsupport for detailed information SAFETY AND CERTIFICATIONS Certificate Type (Safety) Condition Information Technology Equipment, General Requirements for Safety E196683 EAC Standard UL60950-1, 1st Edition CAN/CSA-C22.2 No. 60950-1, 1st Edition RU-AT.49.09571 RoHS2 TP TC 004/2011 RoHS-2011/65/EU + AM-2015/863 EMC Compliance Condition Standard / Criterion Electromagnetic compatibility of multimedia equipment - Emission requirements with external filter (see filter suggestion below) EN55032, Class A and B ESD Electrostatic discharge immunity test Air ±8kV and Contact ±6kV EN61000-4-2, Criteria B 10 V/m EN61000-4-3, Criteria A ±2kV EN61000-4-4, Criteria B ±1kV EN61000-4-5, Criteria B 10 Vr.m.s EN61000-4-6, Criteria A 100A/m continuous; 1000A/m 1s EN61000-4-8, Criteria A Radiated, radio-frequency, electromagnetic field immunity test Fast Transient and Burst Immunity (11) Surge Immunity (11) Immunity to conducted disturbances, induced by radio-frequency fields Power Magnetic Field Immunity Notes: Note11: An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5 Recom suggests Nippon chemi-con KY series 220μF/100V continued on next page www.recom-power.com REV.: 4/2020 PD-6 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) EMC Filtering Suggestions according to EN55032 Single Dual C3 C3 F1 +Vin +Vin C1 +Vout +Vout F1 +Vin +Vin C2 C1 +Vout +Vout C2 Com Com -Vin -Vin -Vout -Vout -Vin -Vin -Vout C4 Component List Class A C3 C3 MODELF +Vin L1 F1 C1 1 +Vin +Vin RP30-12xxSE C RP30-12xxDE1 C2 C5 RP30-24xxSE+V -VRP30-24xxDE in C C -Vin in C1 C2 3 4 C2 +Vout +Vout 6.8μF/50V, 1812 MLCC -V +V 6.8μF/50V, 1812 out out in C6 -Vout C1 C1 C2 N/A-Vin +Vin C1 C2 C3 +Vout -V -V +V +V 1000pF/2kV, 1808 MLCC in in C3 N/A C4 -Vout out out C4 Com Com 1000pF/2kV, 1808 MLCC -Vin -Vin -Vout C6 Single -Vout Dual C5 L1 F1 Com Com C5 +Vin +Vout +Vout C 5 1000pF/2kV, 1808 MLCC C2 L1 F1 +Vin MLCC -Vout 2.2μF/100V, 1812 MLCC -Vout +Vin N/A +Vout C3/C4 F1 +Vin C4 RP30-48xxSE RP30-48xxDE-V -Vin -Vout C4 +Vout +Vout L1 F1 +Vin +Vin C4 C1 C2 C3 +Vout C4 Com -Vin -Vin -Vout -Vout -Vin -Vin C6 -Vout +Vout Com -Vout C6 Component List Class B MODEL RP30-12xxSE RP30-12xxDE RP30-24xxSE RP30-24xxDE RP30-48xxSE RP30-48xxDE C1 4.7μF/50V 1812 MLCC 6.8μF/50V 1812 MLCC 2.2μF/100V 1812 MLCC C2 N/A N/A 2.2μF/100V 1812 MLCC C3 C4 4.7μF/50V 1812 MLCC 6.8μF/50V 1812 MLCC 2.2μF/100V 1812 MLCC N/A N/A 2.2μF/100V 1812 MLCC C5/C6 L1 1000pF/2kV 1808 MLCC 1000pF/2kV 1808 MLCC CMC: 450μH ref.: WE 7448227005 or ref.: CMC-05 CMC: 450μH ref.: WE 7448227005 or ref.: CMC-05 1000pF/2kV 1808 MLCC CMC: 450μH ref.: WE 7448227005 or ref.: CMC-05 DIMENSIONS AND PHYSICAL CHARACTERISTICS Parameter Type Value Material case base potting nickel coated copper FR4 PCB epoxy (UL94-V0) Dimensions (LxWxH) without Heat-sink with Heat-sink 50.8 x 40.6 x 10.2mm 56.8 x 40.6 x 17.0mm Weight without Heat-sink with Heat-sink 48.0g 65.78g continued on next page www.recom-power.com REV.: 4/2020 PD-7 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) Dimension Drawing (mm) Pinning Information 5.6 40.6 10.2 50.8 Pin # 1 2 4 5 6 7 8 Dual +Vin -Vin CTRL +Vout Com -Vout Trim Pin Pitch Tolerance ±0.25mm xx.x = ±0.5mm xx.xx = ±0.25mm 2.54 18 x 2.54= 45.72 Single +Vin -Vin CTRL no Pin +Vout -Vout Trim Ø 1.0±0.1 Recommended Footprint Details 2.54 1 2 2.54 10.16 12.70 6 2 Bottom View 7 4 8 4 1 7 Top View 6 10.16 17.78 15.24 5.08 17.80 5 Ø1.3 +0.15/-0 5 8 Dimension Drawing (mm) with Heat-sink 50.8 40.6 Top View Heat-sink 56.8 5.6 17.0 10.2 5.85 37.5 2.54 18 x 2.54= 45.72 Ø 1.0±0.1 2.54 www.recom-power.com REV.: 4/2020 4 16 0 .80 5 4 Ø1.3 +0.15/-0 PD-8 8 RP30-E DC/DC Converter Series Specifications (measured @ Ta= 25°C, nom. Vin, full load unless otherwise stated) PACKAGING INFORMATION Parameter Type Value Packaging Dimension (LxWxH) tube tray without heat-sink with heat-sink 255.0 x 54.0 x 22.0mm 302.5 x 222.0 x 20.0mm Packaging Quantity tube tray without heat-sink with heat-sink 5pcs 15pcs Storage Temperature Range Storage Humidity -55°C to +125°C non-condensing 5% - 95% RH The product information and specifications may be subject to changes even without prior written notice.The product has been designed for various applications; its suitability lies in the responsibility of each customer. The products are not authorized for use in safety-critical applications without RECOM’s explicit written consent. A safety-critical application is an application where a failure may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The applicant shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV.: 4/2020 PD-9