RP40-483.312TG

POWERLINE - DC/DC-Converter G-Series, 40W, 1.6 kV Isolation, 2:1 Wide Input Range (Single, Dual & Triple Output) Features ● 40 Watts max. Output Power ● 2:1 Wide Input Voltage Range ● International Safety Standard Design ● Six-Sided Continuous Shield Selection Guide 24V and 48V Input Types Part Number Input Voltage VDC RP40-243.3SG RP40-2405SG RP40-2412SG RP40-2415SG RP40-243.312TG RP40-240512TG RP40-243.315TG RP40-240515TG RP40-483.3SG RP40-4805SG RP40-4812SG RP40-4815SG RP40-483.312TG RP40-480512TG RP40-483.315TG RP40-480515TG 18-36 18-36 18-36 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 36-75 36-75 36-75 Output Voltage VDC 3.3 5 12 15 3.3 / ± 12 5 / ± 12 3.3 / ± 15 5 / ± 15 3.3 5 12 15 3.3 / ± 12 5 / ± 12 3.3 / ± 15 5 / ± 15 ● ● ● ● High Efficiency up to 90% Standard Package, 50.8 mm x 50.8 mm x 10.2 mm Fixed Switching Frequency UL 1950 Component Recognised Output Current mA 8000 8000 3400 2700 6000 / ±400 6000 / ±400 6000 / ±300 6000 / ±300 8000 8000 3400 2700 6000 / ±400 6000 / ±400 6000 / ±300 6000 / ±300 Output Ripple & Noise mVp-p 50 50 75 75 50 / 75 50 / 75 50 / 75 50 / 75 50 50 75 75 50 / 75 50 / 75 50 / 75 50 / 75 Input Current (see note 4) mA 1325 1961 2048 2008 1512 1989 1481 1958 655 969 1000 992 747 982 732 967 Efficiency (see note 5) % 87 89 88 88 85 87 85 87 88 90 89 89 86 88 86 88 Capacitive Load max. µF 21000 13600 2360 1510 13000 / ±330 6800 / ±330 13000 / ±110 6800 / ±110 21000 13600 2360 1510 13000 / ±330 6800 / ±330 13000 / ±110 6800 / ±110 RP40-4805SG: Derating and Efficiency Curves, External Output Trimming Derating Curve 125 100 75 Output Power (%) Efficiency (%) 50 25 0 -40 -25 -10 0 50 60 70 80 90 100 Natural Convection Efficiency vs Input Voltage 93 92 91 90 89 88 87 86 85 84 83 82 Efficiency vs Output Load 96 94 92 90 88 86 84 82 80 75 70 65 35 40 45 50 55 60 65 70 Efficiency (%) 1 2 3 4 5 6 7 8 Ambient Temperature Range (°C) Input Voltage (V) Output Load (A) External Output Trimming 8 Trim Up 9 Trim Down 7 PO 68 August 2002 www.recom-international.com POWERLINE - DC/DC-Converter G-Series, 40W, 1.6 kV Isolation, 2:1 Wide Input Range (Single, Dual & Triple Output) Specifications (typical at nominal input and 25°C unless otherwise noted) Output Power Voltage Accuracy (full Load and nominal Vin) Single / Dual Triple Main Auxilliary 40W max. ±1% ±1% ±5% ± 10% Single & Triple Dual (3.3V) Single Dual Triple 10% of FL 800mA ±0.5% ±0.5% ±1% ±2% ±5% See selection guide table ±0.02%/°C max. 400µsec 3.3V Output 5V Output 12V Output 15V Output 3.9V 6.2V 15V 18V 150% max. Hiccup, Automatic Recovery 18-36VDC 36-75VDC 17.8VDC 16VDC 36VDC 34VDC L-C Type 24V Input 48V Input Nominal Vin and full load 50VDC 100VDC 40mAp-p 25ms typ. DC-DC ON DC-DC OFF Nominal Vin Open or 3.5V < Vr < 12V Short or 0V < Vr < 1.2V 2.5 mA 1600VDC 109 Ω 1000pF 300kHz UL 1950, EN60950 Nickel-Coated Copper Non-conducted Black FR4 Epoxy (UL94-V0) 60g (2.11 oz) 50.8 x 50.8 x 10.2 mm 1.434 x 105 Hours continued on next page Voltage Adjustability (single output only) Minimum Load Voltage (see note 1) Line Regulation (LL-HL at FL) Load Regulation (10% to 100% FL) Main Auxilliary Ripple and Noise, 20MHz BW (measured with a 104pF/50V MLCC) Temperature Coefficient Transient Response Recovery Time (25% load step change) Over Voltage Protection (zener diode clamp): Over Load Protection (% of full load at nominal Vin) Short Circuit Protection Input Voltage Range Under Voltage Lockout 24V types nominal input 48V types nominal input 24V Input 48V Input Input Filter Input Surge Voltage (100 ms max.) Input Reflected Ripple (see note 2) Start Up Time (nominal Vin and constant resistor load) Remote ON/OFF (see note 3) DC-DC ON DC-DC OFF DC-DC ON DC-DC OFF Remote off Input Current Isolation Voltage Isolation Resistance Isolation Capacitance Switching Frequency Approved to Safety Standards Case Material Base Material Potting Material Weight Dimensions MTBF (MIL-HDBK-217F, TA = 25°C full load) www.recom-international.com August 2002 PO 69 POWERLINE - DC/DC-Converter G-Series, 40W, 1.6 kV Isolation, 2:1 Wide Input Range (Single, Dual & Triple Output) Specifications continued (typical at nominal input and 25°C unless otherwise noted) Operating Temperature Range Maximum Case Temperature Storage Temperature Range Thermal Impedance Thermal Shock Vibration Relative Humidity Conducted Emissions Radiated Emissions Conducted Immunity Radiated Immunity Surge Fast Transient ESD Air Notes: 1. The RP40 G-series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. 2. Simulated source impedance of 12uH. 12uH inductor in series with +Vin. 3. The ON/OFF control pin voltage is referenced to negative input. 4. Maximum value at nominal input voltage and full load. 5. Typical value at nominal input voltage and full load. 6. It will compensate for up to 0.5V line drop voltage between converter and load. If remote sense is not being used, the +sense should be connected to its corresponding +OUTPUT and likewise the –sense should be connected to its corresponding –OUTPUT. -40°C to +85°C (with derating) +100°C -55°C to +105°C Natural convection 9.2°C/Watt MIL-STD-810D 10-55Hz, 2G, 3 Min. Period, 30 Min. along X, Y and Z 5% to 95% RH EN55022 EN55022 EN61000-4-6 EN61000-4-3 EN61000-4-5 EN61000-4-4 EN61000-4-2 Level A Level A Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Perf. Criteria 2 Package Style and Pinning (mm) 50.80 29.20 10.20 3 2 1 5.10 10.20 Pin Connections Pin # Single +Vin -Vin Ctrl NC -Sense (see note 6) +Sense (see note 6) +Vout –Vout Trim Dual +Vin -Vin Ctrl 3.3V 3.3V RTN NC NC 5V 5V RTN Triple +Vin -Vin Ctrl +Aux Common –Aux +Vout –Vout NC dia. 1.0 Bottom View 50.80 45.70 1 2 3 4 5 6 7 8 9 9 8 7 6 5 4 2.5 7.6 15.20 20.30 5.6 5.1 12.70 Pin Pitch Tolerance ±0.35 mm PO 70 August 2002 www.recom-international.com