RP75-4815SN

Features ● ● ● ● ● ● ● ● Single Output up to 20A Dual Outputs Total Current up to 15A up to 100% Load Imblance Input/Output 1.6kVDC Isolation Adjustable Output Voltage, Independently Regulated Outputs No Minimum Load Industry Standard Footprint Halt Tested Compact 61.0 x 57.91 x 12.7mm Package High Efficiency to 90% INNOLINE DC/DC-Converter RP75-S_DI Series 75 Watt Isolated Single & Dual Output Selection Guide Part Number Input Voltage (VDC) 36 – 75 36 – 75 36 – 75 36 – 75 36 – 75 Input Voltage (VDC) 36 – 75 36 – 75 36 – 75 36 – 75 Output Voltage (VDC) 1.8 2.5 3.3 5 15 Output Current (A) 20 20 20 15 5 Line Load Regulation Regulation (mV) (mV) 4 5 7 10 30 Output Current I1 (A) 15 15 15 15 I2 (A) 15 15 15 15 6 8 10 15 45 Input Efficiency Current (A) % 915 1255 1618 1838 1860 86 88 90 90 90 Single Output RP75-481.8S RP75-482.5S RP75-483.3S RP75-4805S RP75-4815S Part Number Dual Output RP75-483.305DI RP75-483.32.5DI RP75-48051.8DI RP75-483.31.8DI Output Voltage V1 V2 (VDC) (VDC) 5 3.3 5 3.3 3.3 2.5 1.8 1.8 Line Load Efficiency Regulation Regulation (mV) 7/10 7/5 10/4 7/4 (mV) 10/15 10/8 10/15 10/6 % 88 81 85 81 Notes: 1. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used, the +Vsense should be connected to its corresponding +Vout and likewise the -Vsense should be connected to its corresponding -Vout.. 2. Measured with a 1µF M/C and a 10uF M/C(for dual outputs) or 1µF M/C and a 10µF T/C(for single outputs). 3. An external filter capacitor is required for normal operation. The capacitor should be capable of handing 1A ripple current for 48V models. RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90mΩ. 4. The negative / positive logic and length are optional ( see table ). The pin voltage is referenced to negative input. 5. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at Tc=40°C. (Ground fixed and controlled environment) 6. Heat sink is optional and P/N: 7G-0021, 7G-0022, 7G-0023, 7G-0024. 7. The RP75 meets level A and level B conducted emissions only with external components connected before the input pin to the converter. 8. Maximum value at nominal input voltage and full load. 9. Single:Typical value at nominal input voltage and full load. Dual:The efficiency test condition: Nominal input voltage and both outputs current are 7.5A. 10. BASEPLATE GROUNDING:Base-plate should be grounded at one of the four screw bolts prior to operation. 11. The converter is provided by basic insulation. 12. “N” for Negative remote ON/OFF. N 13. “P” for Positive remote ON/OFF. P 186 July-2006 www.recom-international.com INNOLINE DC/DC-Converter Specifications (refer to the standard application circuit, Ta: 25°C) Input Voltage Range Unde-Voltage Lockout Start-up Voltage Unde-Voltage Lockout Shuntdown Voltage Input Filter (Note 3) Input voltage variation Input Surge Voltage 100ms max Start up time Input Reflected-Ripple Current (5Hz to 20Hz, 12µH Source inpedance) Remote ON/OFF (Note 4) (Positive logic) (Negative logic) Continuous Output Power Output Voltage Accuracy (full load and nominal Vin) Output Voltage Adjustment Single (Note 1) Dual Minimum Load Line Regulation Load Regulation Remote Sense (Note 1) Ripple and Noise 20MHz bandwidth (Note 2) Temperature Coefficient Transient Response Recovery Time (25% load step change) Over Voltage Protection threshold (Non-Latching Hiccup) Over Current Protection threshold Maximum Total Output Current Short Circuit Protection Efficiency (at nominal input voltage, full load) Isolation Voltage Input to Output Input to Case Output to Case I1 + I2 Dual low line to high line at full load 0% to 100% full load 36-75VDC 48V input 48V input dv/dt 48V input Nominal Vin and constant resistive load 48V input RP75-S_DI Series 48V nom. 34V typ. 32V typ. L-C type 5V/ms max (Complies with ETS300 132 part4.4) 100VDC 25ms typ. 20mAp-p ON=Open or 3.0V < Vr < 15V, OFF=Short or 0V < Vr < 1.2V, ON=Short or 0V < Vr < 1.2V, OFF=Open or 3.0V < Vr < 15V, IIN=50µA max. IIN=1mA max. IIN=1mA max. IIN=50µA max. 75W max. ±1.5% +10%, -20% +10%, -10% 0% See table See table 10% of Vout 100mVp-p ±0.02%/ºC 200µs 115% ~ 130% of Vout 110% ~ 140% of Iout Rated 15A Hiccup, Automatic recovery up to 90%. 1600VDC min. 1000VDC min. 1000VDC min. 10 7 Isolation Resistance Isolation Capacitance Operating Frequency Operating Temperature Range Over Temperature Protection Storage Temperature Range Humidity max., Non-condensing Thermal Shock Ω min. 2500pF max. 300KHz typ. -40ºC to +100ºC (base plate) 110°C -55°C to +125°C 95% MIL-STD-810D Continued next page www.recom-international.com July-2006 187 INNOLINE DC/DC-Converter Specifications (refer to the standard application circuit, Ta: 25°C) 00Vibration Conducted Emissions RP75-S_DI Series 10 ~ 55Hz 2G, 3minutes period, 30minutes analog EN55022 (Note 7) EN55022 (Note 7) X, Y and Z Level A Level B Level A Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Perf. Criteria2 Open with Aluminium base plate Single Dual 3 Radiated Emisssions ESD Radiated Immunity Fast Transient Surge Conducted Immunity Case Material Weight EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 53g 57g 2000 x10 hours 1300 x10 hours 3 MTBF ( Note 6 ) Single Dual Characteristics Efficiency vs Output Load for 5V only 100 90 80 Efficiency (%) 70 60 50 10 20 30 40 50 60 70 80 90 100 Output Power (%) Ta=25°C 48V Input Without Heatsink 110 90 70 1.) LFM590 2.) LFM400 3.) LFM200 4.) LFM20 48V Input With Heatsink (7G-0022) 110 90 70 1.) LFM590 2.) LFM400 3.) LFM200 4.) LFM20 Output Power (%) 50 30 10 -40 -20 0 20 40 60 1 2 34 Output Power (%) 50 30 10 -40 -20 0 20 40 60 1 2 34 80 100 80 100 Ambient Temperature (°C) Ambient Temperature (°C) 188 July-2006 www.recom-international.com INNOLINE DC/DC-Converter Package Style and Pinning (mm) RP75-S_DI Series 3rd angle projection Single Output 57.91 60.96 12.70 5.08 48.26 Side View 50.80 4xM3 x 0.5 ( Note 10) Pin Connections Pin # Function 1 –Vin 2 Case 3 Remote ON/OFF 4 +Vin 5 –Vout 6 –Vsense 7 Trim 8 +Vsense 9 +Vout XX.X ± 0.5 mm XX.XX ± 0.25 mm Pin pitch tolerance 0.35mm Pin Ø 1.016 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm 1.016 mm 1.016 mm 1.016 mm 2.032 mm 1 2 35.56 15.24 3 4 5 6 7 8 9 17.78 10.16 25.40 Bottom View External Output Trimming Output can be externally trimmed by using the method shown below. Product Options Table Option Negative remote ON/OFF logic, 0.20” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length L K P S M Suffix 7 Trim Up RU 6 Trim Down RD Negative remote ON/OFF logic, 0.11” pin length Positive remote ON/OFF logic, 0.20” pin length Positive remote ON/OFF logic, 0.145” pin length Positive remote ON/OFF logic, 0.11” pin length 8 7 Example: RP75-483.3S/P www.recom-international.com July-2006 189 INNOLINE DC/DC-Converter Package Style and Pinning (mm) RP75-S_DI Series 3rd angle projection Dual Output 57.91 5.08 60.96 12.70 Side View 48.26 50.80 4xM3 x 0.5 ( Note 10) Pin Connections 1 35.56 15.24 3 4 2 5 6 Bottom View 7 8 9 10 25.40 10.16 40.64 Pin # Function 1 –Vin 2 Case 3 Remote ON/OFF 4 +Vin 5 +V2 6 –V2 (Com) 7 V2 Trim 8 +V1 9 +V1 (Com) 10 V1 Trim XX.X ± 0.5 mm XX.XX ± 0.25 mm Pin pitch tolerance 0.35mm Pin Ø 1.016 mm 1.016 mm 1.016 mm 1.016 mm 1.016 mm 1.016 mm 1.016 mm 1.016 mm 1.016 mm 1.016 mm External Output Trimming Output can be externally trimmed by using the method shown below. ( ) for V2 output trim Product Options Table Option Negative remote ON/OFF logic, 0.20” pin length (standard) Negative remote ON/OFF logic, 0.145” pin length Negative remote ON/OFF logic, 0.11” pin length Positive remote ON/OFF logic, 0.20” pin length L K P S M Suffix 9(6) Trim Up RU 10(7) Trim Down RD Positive remote ON/OFF logic, 0.145” pin length Positive remote ON/OFF logic, 0.11” pin length 10(7) 8(5) Example: RP75-483.305I/N July-2006 www.recom-international.com 190