05A6L

SURFACE MOUNT SILICON RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 0.5 Ampere FEATURES * * * * * Ideal for surface mounted applications Low leakage current M etallurgically bonded construction M ounting position: Any Weight: 0.016 g ram 05A1L THRU 05A7L SOD-123FL .114 (2.9) .106 (2.7) .035 (0.90) .028 (0.70) .077 (1.95) .069 (1.75) MECHANICAL DATA * Epoxy : Device has UL flammability classification 94V-0 .008 (0.20) .039 (1.00) .035 (0.90) .150 (3.8) .142 (3.6) .052 (1.32) .050 (1.28) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .033 (0.85) .030 (0.75) .044 (1.12) .043 (1.08) .033 (0.85) .030 (0.75) Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum A verage Forward Rectified Current a t T A = 5 5 o C Peak Forward Surge Current IFM(surge): 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 3) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Ran g e E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Forward Voltage at 0.5A DC Maximum Full Load Reverse Current, Full cycle A verage at TA = 55oC Maximum DC Average Reverse Current at Rated DC Blocking Voltage SYMBOL VF IR 05A1L 05A2L 05A3L 05A4L 1.1 30 @T A = 2 5 o C @T A = 1 00 o C 2.0 50 05A5L 05A6L 05A7L UNITS Volts m Amps m Amps m Amps 2006-12 SYMBOL VRRM VRMS VDC IO I FSM RqJA RqJL CJ T J, T STG 25 8 -55 to + 150 05A1L 50 35 50 05A2L 100 70 100 05A3L 200 140 200 05A4L 400 280 400 0.5 15 85 30 05A5L 600 420 600 05A6L 800 560 800 05A7L 1000 700 1000 UNITS Volts Volts Volts Amps Amps 0 C/W pF 0 C NOTES : 1. Measured at 1.0 MHz and applied average voltage of 4.0VDC 2. “ Fully ROHS compliant”, “100% Sn plating (Pb-free)”. 3. T hernal Resistance: Mounted on PCB. RATING AND CHARACTERISTICS CURVES ( 05A1L THRU 05A7L ) PEAK FORWARD SURGE CURRENT, (A) 0.5 AVERAGE FORWARD CURRENT, (A) 0.4 0.3 0.2 0.1 0 Single Phase Half Wave 60Hz Resistive or Inductive Load 50 40 30 20 10 0 8.3ms Single Half Sine-Wave (JEDED Method) 0 25 50 75 100 125 O 150 175 0 2 4 6 8 10 20 40 60 80 100 AMBIENT TEMPERATURE, ( C) NUMBER OF CYCLES AT 60Hz INSTANTANEOUS REVERSE CURRENT, (mA) INSTANTANEOUS FORWARD CURRENT, (A) 10 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 100 40 10 4 1.0 0.4 0.1 FIG.2 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT TA = 100 OC 1.0 0.1 TA = 100 OC T A = 2 5 OC Pulse Width = 300ms 1% Duty Cycle 0.01 0 0.5 1.0 1.5 2.0 2.5 3.0 0 20 40 60 80 100 120 140 INSTANTANEOUS FORWARD VOLTAGE, (V) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 200 JUNCTION CAPACITANCE, (pF) FIG.4 TYPICAL REVERSE CHARACTERISTICS T A = 2 5 OC 100 60 40 20 10 6 4 2 1 0.1 0.2 0.4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, (V) FIG.5 TYPICAL JUNCTION CAPACITANCE Mounting Pad Layout .052 MIN. (1.32 MIN.) .033 MIN. (0.85 MIN.) .044 MIN. (1.12 MIN.) 0.165 .033 MIN. (0.85 MIN.) (4.19) REF Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.