05H3L

RECTRON SEMICONDUCTOR TECHNICAL SPECIFICATION 05H1L THRU 05H6L SURFACE MOUNT HIGH EFFICIENCY RECTIFIER VOLTAGE RANGE 50 to 600 Volts CURRENT 0.5 Ampere FEATURES * * * * * * * Low power loss, high efficiency Low leakage Low forward voltage High current capability High speed switching High surge capability High reliability .114 (2.9) .106 (2.7) SOD-123FL MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O * Mounting position: Any * Weight: 0.016 gram .035 (0.90) .028 (0.70) .077 (1.95) .069 (1.75) .008 (0.20) .039 (1.00) .035 (0.90) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .030 (0.75) .022 (0.55) .150 (3.8) .142 (3.6) Dimensions in inches and (millimeters) MAXIMUM RATINGS ( At T A = 2 5oC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A= 55 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range SYMBOL VRRM VRMS VDC IO I FSM CJ T J , T STG 15 -55 to + 150 05H1L 50 35 50 05H2L 100 70 100 05H3L 200 140 200 0.5 15 12 05H4L 300 210 300 05H5L 400 280 400 05H6L 600 420 600 UNITS Volts Volts Volts Amps Amps pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.5A DC Maximum DC Reverse Current at Rated DC Blocking Voltage T A = 2 5o C Maximum Full Load Reverse Current Average, Full Cycle .375” (9.5mm) lead length at T L = 5 5oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. SYMBOL VF 05H1L 05H2L 1.0 05H3L 05H4L 1.3 5.0 IR 100 trr 50 75 uAmps nSec 2006-3 REV:O 05H5L 05H6L UNITS 1.7 Volts uAmps RATING AND CHARACTERISTIC CURVES ( 05H1L THRU 05H6L ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) AVERAGE FORWARD CURENT, (A) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 1.0 Single Phase Half Wave 60Hz Resistive or Inductive Load (+) 25 Vdc (approx) (-) D.U.T 0 PULSE GENERATOR -0.25A (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0.5 -1.0A NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 1cm SET TIME BASE FOR 10/20 ns/cm 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (uA) INSTANTANEOUS FORWARD CURRENT, (A) FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 100 10 TJ = 150 1.0 V 00 0/2 50 /10 30 TJ = 100 0/4 00 V 1.0 TJ = 25 .1 .1 .01 TJ = 25 Pulse Width = 300uS 1% Duty Cycle .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 6 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) 21 18 15 12 9 6 3 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 8.3ms Single Half Sine-Wave (JEDEC Method) 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) TJ = 25 05H 05H 1L~ 60 0V 05H 5L 6L RECTRON Mounting Pad Layout 0.014 MIN. (0.36 MIN.) 0.029 MIN. (0.73 MIN.) 0.150 (3.80) REF Dimensions in inches and (millimeters) RECTRON