05S3L

SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 to 60 Volts CURRENT 0.5 Ampere FEATURES * * * * * * * 05S2L THRU 05S6L L ow power loss, high efficiency Low l eakage L ow forward voltage H igh current capability H igh speed switching H igh surge capabitity High r eliability SOD-123FL .114 (2.9) .106 (2.7) .035 (0.90) .028 (0.70) .077 (1.95) .069 (1.75) MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O * Mounting position: Any * Weight: 0.016 g ram .008 (0.20) .039 (1.00) .035 (0.90) .150 (3.8) .142 (3.6) .052 (1.32) .050 (1.28) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .033 (0.85) .030 (0.75) .044 (1.12) .043 (1.08) .033 (0.85) .030 (0.75) Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375” (9.5mm) lead length at T A=55 0C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Cap acitance (Note 1) Typical Thermal Resistance (Note 3) Operating Te mperature Ran g e Storage Temperature R an g e E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.5A DC Maximum Average Reverse Current at Rated DC Blocking Voltage @T A = 2 5 o C @T A = 1 00o C SYMBOL VF IR 05S2L 05S3L .55 0.2 2 05S4L 05S5L .70 05S6L UNITS Volts mAmps mAmps 2006-11 SYMBOL VRRM VRMS VDC IO I FSM CJ RqJA RqJL TJ T STG 05S2L 20 14 20 05S3L 30 21 30 05S4L 40 28 40 0.5 15 110 110 30 150 -55 to + 150 0 0 05S5L 50 35 50 05S6L 60 42 60 UNITS Volts Volts Volts Amps Amps pF C/W C/W 0 0 C C NOTES : 1. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 2. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. 3. Thermal Resistance: Mounted on PCB. RATING AND CHARACTERISTICS CURVES ( 05S2L THRU 05S6L ) INSTANTANEOUS FORWARD CURRENT, (A) 0.5 AVERAGE FORWARD CURRENT, (A) 20 10 0.4 0.3 Single Half Wave 60HZ Resistive or Inductive Load 0.375" (9.5mm) Lead Length 1.0 0.2 05S2L 05S3L 05S4L 05S5L 05S6L T J = 2 5 OC Pulse Width = 300mS 1% Duty Cycle 0.1 0 25 50 75 100 125 O 150 175 0.1 0.1 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 AMBIENT TEMPERATURE, ( C) INSTANTANEOUS FORWARD VOLTAGE, (V) INSTANTANEOUS REVERSE CURRENT, (mA) 05S2L~05S4L INSTANTANEOUS REVERSE CURRENT, (mA) 100 10 1.0 0.1 0.01 0.001 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 100 10 1.0 0.1 0.01 0.001 FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 05S5L~05S6L TA = 125 OC T A = 7 5 OC TA = 125 OC T A = 7 5 OC TA = 25 C O T A = 2 5 OC 0 20 40 60 80 100 120 140 0 20 40 60 80 100 120 140 PERCENT RATED PEAK REVERSE VOLTAGE, (%) PERCENT RATED PEAK REVERSE VOLTAGE, (%) FIG.3 TYPICAL REVERSE CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) FIG.3 TYPICAL REVERSE CHARACTERISTICS 25 20 15 10 5 0 400 CT, TOTAL CAPACITANCE, (pF) T J = 2 5 OC 200 100 80 60 40 20 10 8.3mS Single Half Sine-Wave JEDEC Method 0.1 0.4 1.0 4 10 40 80 1 2 4 6 8 10 20 40 80 100 REVERSE VOLTAGE, (V) NUMBER OF CYCLES AT 60Hz FIG.4 TYPICAL JUNCTION CAPACITANCE FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Mounting Pad Layout .052 MIN. (1.32 MIN.) .033 MIN. (0.85 MIN.) .044 MIN. (1.12 MIN.) 0.165 .033 MIN. (0.85 MIN.) (4.19) REF Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.