10A6

RECTRON SEMICONDUCTOR TECHNICAL SPECIFICATION 10A05 THRU 10A10 SILICON RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 10 Amperes FEATURES * * * * * Low cost Low leakage Low forward voltage drop High current capability High surge current capability R-6 MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 2.08 grams 1.0 (25.4) MIN. .052 (1.3) DIA. .048 (1.2) .360 (9.1) .340 (8.6) .360 (9.1) DIA. .340 (8.6) 1.0 (25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 5 0 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note) Typical Thermal Resistance Operating and Storage Temperature Range ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 10A DC @T A = 2 5 o C Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 1 00 o C Maximum Full Load Reverse Current Average Full Cycle .375” (9.5mm) lead length at T L = 7 5oC NOTES : Measured at 1 MHZ and applied reverse voltage of 4.0 volts SYMBOL VF 10A05 10A1 10A2 10A4 1.1 10 100 50 10A6 10A8 10A10 UNITS Volts uAmps uAmps 2002-3 SYMBOL VRRM VRMS VDC IO I FSM CJ R θJA T J , T STG 10A05 50 35 50 10A1 100 70 100 10A2 200 140 200 10A4 400 280 400 10 400 125 8 -65 to + 150 0 10A6 600 420 600 10A8 800 560 800 10A10 1000 700 1000 UNITS Volts Volts Volts Amps Amps pF C/ W 0 C IR RATING AND CHARACTERISTIC CURVES ( 10A05 THRU 10A10 ) AVERAGE FORWARD CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE Single Phase Half Wave 60Hz Resistive or Inductive Load 10 8 6 4 2 0 0 Standard PC Board Mounting 20 40 60 80 100 120 140 160 180 200 AMBIENT TEMPERATURE, ( ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS FIG. 2 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (uA) 1000 INSTANTANEOUS FORWARD CURRENT, (A) 100 100 10 TJ = 100 10 TJ = 25 Pulse Width=300uS 1% Duty Cycle 1.0 1.0 TJ = 25 .1 .1 .6 .01 .8 1.0 1.2 1.4 1.6 1.8 2.0 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 3 - MAXIMUM NON-REPETITIVE FORWARD 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) PEAK FORWARD SURGE CURRENT, (A) 600 500 400 300 200 TJ = 25 THERMAL RESISTANCE (¢J/W) SURGE CURRENT FIG. 5 - TYPICAL THERMAL RESISTANCE VS LEAD LENGTH 25 20 15 10 5 0 0 .1 .2 .3 .4 .5 .6 .7 .8 .9 1.0 EQUAL LEAD LENGTH TO HEAT SINK, (IN.) 100 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 RECTRON