1E3

RECTRON SEMICONDUCTOR TECHNICAL SPECIFICATION 1E1 THRU 1E4 GLASS PASSIVATED SUPER FAST RECTIFIER VOLTAGE RANGE 50 to 200 Volts CURRENT 1.0 Ampere FEATURES * * * * * * * High reliability Low leakage Low forward voltage High current capability Super fast switching speed High surge capability Good for switching mode circuit R-1 MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.19 gram .025 (0.65) DIA. .021 (0.55) .787 (20.0) MIN. .126 (3.2) .106 (2.7) .102 (2.6) DIA. .091 (2.3) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .787 (20.0) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS ( At TA = 2 5oC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Volts Maximum DC Blocking Voltage Maximum Average Forward Current at T A = 2 5 oC Peak Forward Surge Current I FM ( surge):8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range SYMBOL VRRM VRMS VDC IO I FSM CJ T J , T STG 1E1 50 35 50 1E2 100 70 100 1.0 25 15 -55 to + 150 1E3 150 105 150 1E4 200 140 200 UNITS Volts Volts Volts Amps Amps pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Forward Voltage at 1.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF=0.5A, IR=-1.0A, IRR=-0.25A. 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts. 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. @T A = 2 5 o C @T A = 150 o C SYMBOL VF IR trr 1E1 1E2 0.95 5.0 50 35 nSec 2005-1 REV:A 1E3 1E4 UNITS Volts uAmps RATING AND CHARACTERISTIC CURVES ( 1E1 THRU 1E4 ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC AVERAGE FORWARD CURENT, (A) 50 NONINDUCTIVE 10 NONINDUCTIVE FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 2.0 Single Phase Half Wave 60Hz Resistive or Inductive Load trr +0.5A (-) PULSE GENERATOR (+) 25 Vdc (approx) (-) D.U.T 0 -0.25A 1.0 (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 0 0 25 50 75 100 125 150 175 1cm SET TIME BASE FOR 10 ns/cm AMBIENT TEMPERATURE ( ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, (A) FIG. 4 - TYPICAL INSTANTANEOUS FORWARD 100 INSTANTANEOUS REVERSE CURRENT, (uA) 10 CHARACTERISTICS TJ = 150 10 TJ = 100 1.0 TJ = 25 1.0 .1 .1 TJ = 25 .01 Pulse Width = 300uS 1% Duty Cycle .01 .001 0 20 40 60 80 100 120 140 0 .2 .4 .6 .8 1.0 1.2 1.4 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) FIG. 6 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) 35 30 25 20 15 10 5 0 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz 8.3ms Single Half Sine-Wave (JEDEC Method) 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 TJ = 25 REVERSE VOLTAGE, ( V ) RECTRON DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do var y in different applications and actual performance may var y over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitr y may directly or indirectly cause injur y or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures. RECTRON