1N4008

1N4008 SILICON RECTIFIER VOLTAGE RANGE 1200 Volts CURRENT 1.0 Ampere FEATURES * * * * Low cost Low leakage Low forward voltage drop High current capability MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.33 gram 1.0 (25.4) MIN. .205 (5.2) .166 (4.2) .034 (0.9) DIA. .028 (0.7) .107 (2.7) .080 (2.0) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS DIA. 1.0 (25.4) MIN. Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 C unless otherwise noted) o SYMBOL 1N4008 UNITS Maximum Recurrent Peak Reverse Voltage VRRM 1200 Volts Maximum RMS Voltage VRMS 840 Volts VDC 1200 Volts IO 1.0 Amps I FSM 30 Amps I 2T CJ 3.74 R JA T J , T STG 50 -55 to + 150 SYMBOL VF 1N4008 1.0 0.2 200 RATINGS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current o at T A = 75 C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Current Squared Time Typical Junction Capacitance (Note) Typical Thermal Resistance Operating and Storage Temperature Range 2 AS pF 15 0 C/ W 0 C ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted) o CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC o @T A = 25 C Maximum DC Reverse Current o at Rated DC Blocking Voltage @T A = 150 C Maximum Full Load Reverse Current Average, Full Cycle .375” (9.5mm) lead length at TL = 75oC NOTES : 1.Measured at 1 MH Z and applied reverse voltage of 4.0 volts IR 20 UNITS Volts uAmps uAmps 2020-11 REV:A RATING AND CHARACTERISTIC CURVES ( 1N4008 ) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE FIG. 2 - MAXIMUM INSTANTANEOUS FORWARD CHARACTERISTICS INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD RECTIFIED CURRENT, (A) 1.0 .8 .6 .4 Single Phase Half Wave 60Hz Resistive or Inductive Load .2 30 20 10 0 1 2 4 6 8 10 20 40 60 80 100 NUMBER OF CYCLES AT 60Hz INSTANTANEOUS REVERSE CURRENT, (uA) 8.3ms Single Half Sine-Wave (JEDED Method) .4 .2 .1 TJ = 25 Pulse Width=300uS 1% Duty Cycle .04 .8 1.0 1.2 1.4 1.5 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 4 - MAXIMUM REVERSE CHARACTERISTICS 1000 100 1.0 .2 TA = 25 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) PEAK FORWARD SURGE CURRENT, (A) 25 50 75 100 125 150 175 AMBIENT TEMPERATURE, ( ) FIG. 3 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 50 40 4 2 1.0 .02 .01 .6 0 0 20 10 200 100 60 40 20 10 TJ = 25 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) RECTRON AXIAL LEAD TAPING SPECIFICATIONS FOR RECTIFIERS Axial lead devices are packed in accordance with EIA standard RS-296-D and specifications given below. COMPNENT OUTLINE COMPONENT PITCH A 0.5mm (.020") T-1 R-1 A-405 A-405 DO-41 DO-41 DO-15 R-3 DO-201AD R-6 INNER TAPE PITCH B 0.5mm (.020") 1.5mm (.059") 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 10.0mm 10.0mm 26.0mm 26.0mm 26.0mm 52.4mm 26.0mm 52.4mm 52.4mm 52.4mm 52.4mm 52.4mm O Z CUMULATIVE PITCH TOLERANCE 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch O 90 5 DO A E W L1 D1 B L2 D T E Fig.: Configuration of AXIAL LEAD TAPING ITEM Component alignment Tape width Exposed adhesive Body eccentricity Reel outside diameter Reel inner diameter Feed hole diameter Reel width Notes : SYMBOL Z T E IL1-L2I D D1 DO W SPECIFICATIONS (mm) 1.2 Max. 6.0 0.4 0.8 Max. 1.0 Max. 330.0 85.7 0.3 30.5 0.4 79.0 1.0 1.Each component lead shall be sandwiched between tapes for a minimum of 3.2mm (0.126"). 2.The reel width "W" for 26mm taping is 50.0 1.0mm (1.97" 0.040"). SPECIFICATIONS (inch) 0.047 Max. 0.236 0.016 0.032 Max. 0.039 Max. 13.0 3.374 0.012 1.201 0.016 3.110 0.039 PACKAGING OF DIODE AND BRIDGE RECTIFIERS BULK PACK PACKAGE PACKING CODE DO-41 -B EA PER BOX INNER BOX SIZE (mm) 1,000 194*75*21 CARTON SIZE EA PER CARTON (mm) 415*220*255 50,000 GROSS WEIGHT(Kg) 16.2 REEL PACK PACKAGE DO-41 PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX -T 5,000 5,000 5.0 52 330 355*350*335 20,000 10.49 AMMO PACK PACKAGE PACKING CODE REEL ( EA ) COMPONENT TAPE SPACE SPACE(mm) (mm) DO-41 -F 3,000 5.0 52 DO-41 -E 3,000 5.0 26 BOX SIZE (mm) CARTON SIZE(mm) CARTON ( EA ) GROSS WEIGHT (Kg) 255*73*100 400*268*225 30,000 13.0 256*48*94 42,000 12.41 365*270*217 RECTRON Attachment information about 1N4008 1. Internal Circuit Anode Cathode 2. Marking on the body Cathode Band Plant - code Year - code V X X Rectron Logo Part No. Month - code 1N 4 0 0 8 8---1200V 3. The net weight 330mg / pcs 4. Taping packaging specification 4.1 All polarized components must be oriented in one direction. 4.2 For diode, at least one side of the cathode lead tape should be red, and anode lead tape should be white. 4.3A minimum 300 mm (12”) leader shall be provided at each end of the reel. 4.4 Staples shall not be used for splicing. Splice length shall be 4.0 inches minimum and shall not be misaligned more than 0.8mm. RECTRON Attachment information about 1N4008 5. Items marked on the reel box and carton 5.1 On the reel (for –T) CUSTOMER TYPE QUANTITY LOT NO. Q.A. REMARK 5.2 On the box (for –E & -F) TYPE QUANTITY LOT NO. Q.A. 5.3 On the carton CUSTOMER TYPE QUANTITY LOT NO. REMARK 1. BOX Packing L W H Code (mm) (mm) (mm) -F 255 100 73 -E 256 94 46 2. REEL D Packing D Code (mm) -T 178 -W 330 Packing L W H Code (mm) (mm) (mm) -T 355 350 335 -F 402 270 225 -E 347 320 220 3. CARTON DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein to make corrections modifications enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed intended or authori ed for use in medical life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause in ury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims damages and expenditures.