5KP26CA-T

TVS 5KP SERIES GPP TRANSIENT VOLTAGE SUPPRESSOR 5000 WATT PEAK POWER 8.0 WATTS STEADY STATE FEATURES * * * * * * Plastic package has underwriters laboratory Glass passivated chip construction 5000 watt surage capability at 1ms Excellent clamping capability Low zener impedance Fast response time R-6 1.0 (25.4 ) MIN. .052 (1.3 ) .048 (1.2 ) DIA. .360 (9.1 ) .340 (8.6 ) .360 (9.1 ) .340 (8.6 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS DIA. 1.0 (25.4 ) MIN. o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load, For capacitive load, derate current by 20%. 'LPHQVLRQVLQLQFKHVDQGPLOOLPHWHUV DEVICES FOR BIPOLAR APPLICATIONS For Bidirectional use C or CA suffix for types 5KP5.0 thru 5KP110 Electrical characteristics apply in both direction MAXIMUM RATINGS (At TA = 25 oC unless otherwise noted) SYMBOL VALUE UNITS Peak Pulse Power Dissipation with a 10/1000uS waveform (Note 1, FIG.1) P PPM Minimum 5000 Watts Peak Pulse Current with a 10/1000uS waveform (Note 1, Fig. 3) I PPM SEE TABLE 1 Amps P M(AV) 8.0 Watts Peak Forward Surge Current, 8.3ms single half sine wavesuperimposed on rated load( JEDEC METHOD ) (Note 3) I FSM 400 Amps Typical Current Squared Time I 2T 664 A 2S VF 3.5 Volts T J , T STG -55 to + 150 RATINGS Steady State Power Dissipation at T L = 75oC lead lengths 0.375” (9.5mm) (Note 2) Instantaneous Forward Voltage at 100A, (Note 3) Operating and Storage Temperature Range o NOTES : 1. Non-repetitive current pulse, per Fig.3 and derated above TA = 25 C per Fig.2. 2. Mounted on copper pad area of 0.8 X 0.8” ( 20 X 20mm ) per Fig. 5 3. Measured on 8.3mS single half sine-wave or equivalent square wave, duty cycle = 4 pulses per minute maximum. 0 C 2016-09 REV: B Non-Repetitive Pulse Waveform Shown in Fig.3 TA = 25 10 1.0 0.1 0.1uS 1.0uS 10uS 100uS 1.0mS 10mS FIG. 2 - PULSE DERATING CURVE (IPP) DERATING IN PERCENTAGE,% PPPM, PEAK PULSE POWER, kW FIG. 1 - PEAK PULSE POWER RATING CURVE 100 PEAK PULSE POWER (PPP) OR CURRENT RATING AND CHARACTERISTIC CURVES ( 5KP5.0 THRU 5KP110CA ) 100 75 50 25 0 0 25 TP, PULSE WIDTH, sec 100 125 150 175 200 ) 100000 tr = 10usec. f = 1.0 MHz Vsig = 50mVp-p TJ = 25 Pulse Width (td) is Defined as the Point Where the Peak Current Decays to 50% of IPPM Peak Value IPPM CJ, CAPACITANCE, pF IPPM, PEAK PULSE CURRENT,% 75 FIG. 4 - TYPICAL JUNCTION CAPACITANCE FIG. 3 - PULSE WAVEFORM 150 100 IPPM HALF VALUE 2 10/1000usec. Waveform as Defined by R.E.A. 50 Measured at Stand off Voltage,VWM 1000 td 0 100 1.0 2.0 t, TIME,mS 3.0 4.0 1.0 L = 0.375"(9.5mm) Lead Lengths 60Hz Resistive or Inductive Load 6 4 0.8X0.8X0.040" (20X20mm) Copper Heat Sinks 0 IFSM, PEAK FORWARD SURGE CURRENT AMPERES 8 10 100 200 V(BR), BREAKDOWN VOLTACE, VOLTS FIG. 6 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT UNIDIRECTIONAL FIG. 5 - STEADY STATE POWER DERATING CURVE 2 Measured at Zero Bias 10000 0 PM(AV), STEADY STATE POWER DISSIATION, WATTS 50 TA, AMBIENT TEMPERATURE,( 400 8.3ms Single Half Sine-Wave (JEDED Method) 350 300 250 200 150 100 0 25 50 75 100 125 150 TL, LEAD TEMPERATURE ( 175 ) 200 1 10 NUMBER OF CYCLES AT 60 Hz 100 TRANSIENT VOLTAGE SUPPRESSORS 5000W SERIES TVS DIODES/R-6 ( CASE 12 ) 5000W TYPE 5KP5.0 5KP5.0A 5KP6.0 5KP6.0A 5KP6.5 5KP6.5A 5KP7.0 5KP7.0A 5KP7.5 5KP7.5A 5KP8.0 5KP8.0A 5KP8.5 5KP8.5A 5KP9.0 5KP9.0A 5KP10 5KP10A 5KP11 5KP11A 5KP12 5KP12A 5KP13 5KP13A 5KP14 5KP14A 5KP15 5KP15A 5KP16 5KP16A 5KP17 5KP17A 5KP18 5KP18A 5KP20 5KP20A 5KP22 5KP22A 5KP24 5KP24A 5KP26 5KP26A 5KP28 5KP28A 5KP30 5KP30A MIN. MAX. (mA) Reverse Stand off Voltage VWM (Volts) 6.40 6.40 6.67 6.67 7.22 7.22 7.78 7.78 8.33 8.33 8.89 8.89 9.44 9.44 10.0 10.0 11.1 11.1 12.2 12.2 13.3 13.3 14.4 14.4 15.6 15.6 16.7 16.7 17.8 17.8 18.9 18.9 20.0 20.0 22.2 22.2 24.4 24.4 26.7 26.7 28.9 28.9 31.1 31.1 33.3 33.3 7.30 7.00 8.15 7.37 8.82 7.98 9.51 8.60 10.2 9.21 10.9 9.83 11.5 10.4 12.2 11.1 13.6 12.3 14.9 13.5 16.3 14.7 17.6 15.9 19.1 17.2 20.4 18.5 21.8 19.7 23.1 20.9 24.4 22.1 27.1 24.5 29.8 26.9 32.6 29.5 35.3 31.9 38.0 34.4 40.7 36.8 50 50 50 50 50 50 50 50 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 6.0 6.0 6.5 6.5 7.0 7.0 7.5 7.5 8.0 8.0 8.5 8.5 9.0 9.0 10.0 10.0 11.0 11.0 12.0 12.0 13.0 13.0 14.0 14.0 15.0 15.0 16.0 16.0 17.0 17.0 18.0 18.0 20.0 20.0 22.0 22.0 24.0 24.0 26.0 26.0 28.0 28.0 30.0 30.0 Breakdown Voltage VBR @IT (Volts) Maximum Reverse Leakage at VWM ID(uA) Maximum Peak Pulse Current IPPM (Amps) Maximum Clamping Voltage at IPPM VC (Volts) 2000 2000 5000 5000 2000 2000 1000 1000 250 250 150 150 50 50 20 20 15 15 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 521 543 439 485 407 446 376 417 350 388 333 368 314 347 296 325 266 294 249 275 227 251 210 233 194 216 186 205 174 192 164 181 155 171 140 154 127 141 116 129 107 119 100 110 93.5 103 9.6 9.2 11.4 10.3 12.3 11.2 13.3 12.0 14.3 12.9 15.0 13.6 15.9 14.4 16.9 15.4 18.8 17.0 20.1 18.2 22.0 19.9 23.8 21.5 25.8 23.2 26.9 24.4 28.8 26.0 30.5 27.6 32.2 29.2 35.8 32.4 39.4 35.5 43.0 38.9 46.6 42.1 50.1 45.4 53.5 48.4 TRANSIENT VOLTAGE SUPPRESSORS 5000W SERIES TVS DIODES/R-6 ( CASE 12 ) 5000W TYPE 5KP33 5KP33A 5KP36 5KP36A 5KP40 5KP40A 5KP43 5KP43A 5KP45 5KP45A 5KP48 5KP48A 5KP51 5KP51A 5KP54 5KP54A 5KP58 5KP58A 5KP60 5KP60A 5KP64 5KP64A 5KP70 5KP70A 5KP75 5KP75A 5KP78 5KP78A 5KP85 5KP85A 5KP90 5KP90A 5KP100 5KP100A 5KP110 5KP110A Notes : Breakdown Voltage VBR @IT (Volts) MIN. MAX. (mA) Reverse Stand off Voltage VWM (Volts) 36.7 36.7 40.0 40.0 44.4 44.4 47.8 47.8 50.0 50.0 53.3 53.3 56.7 56.7 60.0 60.0 64.4 64.4 66.7 66.7 71.1 71.1 77.8 77.8 83.3 83.3 86.7 86.7 94.4 94.4 100 100 111 111 122 122 44.9 40.6 48.9 44.2 54.3 49.1 58.4 52.8 61.1 55.3 65.2 58.9 69.3 62.7 73.3 66.3 78.7 71.2 81.5 73.7 96.9 78.6 95.1 86.0 102 92.1 106 95.8 115 104 122 111 136 123 149 135 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 33.0 33.0 36.0 36.0 40.0 40.0 43.0 43.0 45.0 45.0 48.0 48.0 51.0 51.0 54.0 54.0 58.0 58.0 60.0 60.0 64.0 64.0 70.0 70.0 75.0 75.0 78.0 78.0 85.0 85.0 90.0 90.0 100 100 110 110 Maximum Reverse Leakage at VWM ID(uA) Maximum Peak Pulse Current IPPM (Amps) Maximum Clamping Voltage at IPPM VC (Volts) 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 84.7 93.8 77.8 86.1 70.0 77.5 65.2 72.0 62.3 68.8 58.5 64.6 54.9 60.7 51.9 57.4 48.5 53.4 46.7 51.7 43.9 48.5 40.0 44.2 37.3 41.3 36.0 39.7 33.1 36.5 31.3 34.2 27.9 30.9 25.5 28.2 59.0 53.3 64.3 58.1 71.4 64.5 76.7 69.4 80.3 72.7 85.5 77.4 91.1 82.4 96.3 87.1 103 94 107 97 114 103 125 113 134 121 139 126 151 137 160 146 179 162 196 177 1. VBR measured after IT applied for 300us. IT = square pulse or equivalent. 2. All devices UL listed under file# E211196. Attachment information about 5KPXXX Mark Description Plant - code Rectron Logo Part No. V Y M 5 K P XXX Year – code (Y: Last digit of year&A:2010,B:2011…) Month – code (M: 0~9, O ,N ,D ) Voltage Range PACKAGING OF DIODE AND BRIDGE RECTIFIERS BULK PACK PACKAGE PACKING CODE R-6/R-7 -B EA PER BOX INNER BOX SIZE (mm) 200 300*73*40 CARTON SIZE EA PER CARTON (mm) GROSS WEIGHT(Kg) 347*320*271 12.93/14.57 4,800 REEL PACK PACKAGE R-6/R-7 PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX -T 800 9.5 800 52 330 355*350*335 3,200 9.72/9.91 AMMO PACK PACKAGE PACKING CODE R-6/R-7 -F REEL ( EA ) 300 COMPONENT TAPE SPACE SPACE(mm) (mm) 9.5 52 BOX SIZE (mm) CARTON SIZE(mm) 255*73*100 400*268*225 CARTON ( EA ) 3,000 GROSS WEIGHT (Kg) 8.5/8.7 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.