6A6-T

6A05 THRU 6A10 SILICON RECTIFIER VOLTAGE RANGE 1000 Volts CURRENT 6.0 Amperes FEATURES * * * * * High surge current capability Low leakage Low forward voltage drop High current capability Low lost R-6 MECHANICAL DATA * * * * Case: Molded plastic black body Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any .052 (1.3) .945 (24) MIN. DIA. .048 (1.2) .360 (9.1) .340 (8.6) .360 (9.1) .340 (8.6) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS DIA. .945 (24) MIN. Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage o Maximum Average Forward Rectified Current at T A = 50 C Peak Forward Surge Current IFM(surge): 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Current Squarad Time 6A05 6A1 6A2 Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range 6A6 6A8 6A10 UNITS 1000 VRMS 700 Volts VDC 1000 Volts Volts IO 6.0 Amps I FSM 400 Amps 2 663.7 A Sec I t Typical Thermal Resistance (Note 2) 6A4 VRRM R1JA 10 CJ 150 T J, T STG -55 to + 150 2 0 C/W pF 0 C ELECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) O SYMBOL CHARACTERISTICS Maximum Forward Voltage at 6.0A DC Maximum DC Average Reverse Current at Rated DC Blocking Voltage VF o @T A = 25 C o @T A = 150 C NOTES : 1. Measured at 1.0 MHz and applied average voltage of 4.0VDC 2. Thernal Resistance: At 9.5mm lead lengths,PCB mounted. IR 6A05 6A1 6A2 6A4 6A6 6A8 6A10 UNITS 1.0 Volts 0.3 uAmps 1.5 m Amps 2022-11 REV:J RATING AND CHARACTERISTICS CURVES ( 6A05 THRU 6A10 ) PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) 6.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 4.5 Ground pane 1" x 1" Copper surface area PC BOARD Recommended PC Board Mounting 3.0 PC BOARD 1.5 Standard PC Board Mounting 0 250 50 75 100 125 150 500 8.3ms Single Half Sine-Wave (JEDED Method) 400 300 200 100 0 0 175 2 4 O INSTANTANEOUS REVERSE CURRENT, (uA) 100 10 TJ = 25 OC 1.0 Pulse Width = 300ms 1% Duty Cycle 0.1 0 0.5 1.0 1.5 86 10 20 40 60 80 100 NUMBER OF CYCLES AT 60Hz FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 2.0 2.5 3.0 E FORWARD FIG.2 MAXIMUM NON-REPETITIIVE SURGE CURRENT 10000 TA =150 O C 1000 10 TA = 25 OC 1.0 0.1 0 INSTANTANEOUS FORWARD VOLTAGE, (V) 20 40 60 100 FIG.4 MAXIMUM REVERSE CHARACTERISTICS 25 20 15 10 5 0.1 80 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.3 MAXIMUM INSTANTANEOUS FORWARD CHARACTERISTICS THERMAL RESISTANCE, (OC/W) INSTANTANEOUS FORWARD CURRENT, (A) AMBIENT TEMPERATURE, ( C) .0.2 0.3 0.4 .0.5 0.6 0.7 0.8 0.9 1.0 EQUAL LEAD LENGTH TO HEAT SINK, (IN.) FIG.5 TYPICAL THERMAL RESISTANCE vs. LEAD LENGTH 140 Marking Description Rectron Logo Part No. V Y M 6AH Cathode Band Year – code: (Y:Last digit of year) Month – code: (M:0~9,O,N,D) H---for all Voltage rang AXIAL LEAD TAPING SPECIFICATIONS FOR RECTIFIERS Axial lead devices are packed in accordance with EIA standard RS-296-D and specifications given below. COMPNENT OUTLINE COMPONENT PITCH A 0.5mm (.020") T-1 R-1 5.0mm 5.0mm INNER TAPE PITCH B 0.5mm (.020") 1.5mm (.059") CUMULATIVE PITCH TOLERANCE 2.0mm/20pitch 2.0mm/20pitch 26.0mm 26.0mm R-1 5.0mm A-405 A-405 DO-41 DO-41 DO-15 R-3 DO-201AD 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 10.0mm 52.4mm 2.0mm/20pitch R-6 10.0mm 52.4mm 2.0mm/10pitch 1.5KE 10.0mm 52.4mm 2.0mm/10pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 26.0mm 52.4mm 26.0mm 52.4mm 52.4mm 52.4mm 52.4mm Note: -E for 26mm inner tape pitch -F & -T for 52mm inner tape pitch Z O O 90 5 DO A E W L1 D1 B L2 D T E Fig.: Configuration of AXIAL LEAD TAPING ITEM Component alignment Tape width Exposed adhesive Body eccentricity Reel outside diameter Reel inner diameter Feed hole diameter Reel width Notes : SYMBOL Z T E IL1-L2I D D1 DO W SPECIFICATIONS (mm) 1.2 Max. 6.0 0.4 0.8 Max. 1.0 Max. 330.0 85.7 0.3 30.5 0.4 79.0 1.0 1.Each component lead shall be sandwiched between tapes for a minimum of 3.2mm (0.126"). 2.The reel width "W" for 26mm taping is 50.0 1.0mm (1.97" 0.040"). SPECIFICATIONS (inch) 0.048 Max. 0.236 0.016 0.032 Max. 0.040 Max. 13.0 3.375 0.012 1.201 0.016 3.110 0.040 2002-12 PACKAGING OF DIODE AND BRIDGE RECTIFIERS BULK PACK PACKAGE PACKING CODE R-6/R-7 -B EA PER BOX INNER BOX SIZE (mm) 200 300*73*40 CARTON SIZE EA PER CARTON (mm) GROSS WEIGHT(Kg) 347*320*271 12.93/14.57 4,800 eg(TYPE):6A10-B REEL PACK PACKAGE PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX R-6/R-7 -T 800 9.5 800 52 330 355*350*335 3,200 9.72/9.91 eg(TYPE):6A10-T AMMO PACK PACKAGE PACKING CODE R-6/R-7 -F eg(TYPE):6A10-F REEL ( EA ) 300 COMPONENT TAPE SPACE SPACE(mm) (mm) 9.5 52 BOX SIZE (mm) CARTON SIZE(mm) 255*73*100 400*268*225 CARTON ( EA ) 3,000 GROSS WEIGHT (Kg) 8.5/8.7 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.