BC807-16

BC807-16 SOT-23 BIPOLAR TRANSISTORS TRANSISTOR(PNP) FEATURES * Ldeally suited for automatic insertion * Epitaxial planar die construction * Complementary NPN type available(BC817) SOT-23 COLLECTOR 3 MECHANICAL DATA * * * * * BASE Case: Molded plastic Epoxy: UL 94V-O rate flame retardant Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.008 gram 1 EMITTER 2 0.055(1.40) 0.047(1.20) 0.006(0.15) 0.003(0.08) 0.020(0.50) 0.012(0.30) 0.043(1.10) 0.035(0.90) 0.004(0.10) 0.000(0.00) 0.020(0.50) 0.012(0.30) 0.100(2.55) 0.089(2.25) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. O 0.019(2.00) 0.071(1.80) 1 3 2 0.118(3.00) 0.110(2.80) Dimensions in inches and (millimeters) MAXIMUM RATINGS ( @ TA = 25 C unless otherwise noted ) CHARACTERISTICS Collector-base voltage Collector-emitter voltage Emitter-base voltage Collector current-continuous Collector dissipation Junction and storage temperature o o SYMBOL VCBO VCEO VEBO IC PC TJ,Tstg VALUE -50 -45 -5 -0.5 0.3 -55 -150 UNITS V V V A W o C ELECTRICAL CHARACTERISTICS ( @ TA = 25 C unless otherwise noted ) CHARACTERISTICS Collector-base breakdown voltage (IC= -10mA, IE=0) Collector-emitter breakdown voltage (IC= -10mA, IB=0) Emitter-base breakdown voltage (IE= -1mA, IC=0) Collector cut-off current (VCB= -45V, IE=0) Collector cut-off current (VCE= -40V, IB=0) Emitter cut-off current (VEB= -4V, IC=0) DC current gain (VCE= -1V, IC= -100mA) Collector-emitter saturation voltage (IC= -500mA, IB= -50mA) Base-emitter saturation voltage (IC= -500mA, IB= -50mA) Transition frequency (VCE= -5V, IC= -10mA, f= 100MHZ) MARKING NOTE: “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. SYMBOL VCBO VCEO VEBO ICBO ICEO IEBO hFE(1) VCE(sat) VBE(sat) MIN -50 -45 -5 100 100 5A 2007-3 MAX -0.1 -0.2 -0.1 250 -0.7 -1.2 UNITS V V V mA mA mA V V MHZ fT RATING AND CHARACTERISTICS CURVES ( BC807-16 ) 400 1000 See Note 1 TA=25 C f=20MHZ O 300 fT, GAIN BANDWIDTH PRODUCT(MHZ) Pd , POWER DISSIPATION (mW) -VCE=5.0V 200 100 1.0V 100 0 0 100 TSB, SUBSTRATE TEMPERATURE( C) O 200 10 1 10 100 1000 -VCESAT, COLLECTOR SATURATION VOLTAGE (V) Figure.1 Power Derating Curve 0.5 0.4 0.3 0.2 0.1 0 150 C O Typical limits O at TA=25 C -IC / - IB= 10 1000 Figure.2 GAIN-BANDWIDTH PRODUCT vs COLLECTOR CURRENT -VCE= 1V 150 C 25 C -50 C O O O -IC, COLLECTOR CURRENT (mA) hFE, DC CURRENT GAIN -50 C O 100 25 C O 0.1 Figure.3 Collector Sat Voltage vs Collector Current 500 3.2 2.8 -Ic,COLLECTOR CURRENT(mA) 1 10 100 1000 10 0.1 1 -Ic, COLLECTOR CURRENT (mA) 10 100 1000 Figure.4 DC Current Gain vs Collector Current 100 0.35 -Ic, COLLECTOR CURRENT (mA) -Ic, COLLECTOR CURRENT (mA) 2.4 2 1.8 1.6 1.4 1.2 0.8 0.6 400 80 0.3 0.25 300 60 0.2 0.15 0.1 200 40 100 0.4 20 0 -IB= 0.05mA 0 -IB= 0.2mA 0 1 -VCE, COLLECTOR - EMITTER VOLTAGE (V) 2 0 Figure.5 Typical Emitter-Collector Characteristics Figure.6 Typical Emitter-Collector Characteristics -VCE, COLLECTOR-EMITTER VOLTAGE (V) 10 20 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.