BC817-40

BC817-16 BC817-25 BC817-40 SOT-23 BIPOLAR TRANSISTORS TRANSISTOR (NPN) FEATURES * For general AF applications * High collector current * High current gain * Low collector-emitter saturation voltage SOT-23 COLLECTOR 3 MECHANICAL DATA * * * * * BASE Case: Molded plastic Epoxy: UL 94V-O rate flame retardant Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.008 gram 1 EMITTER 2 0.055(1.40) 0.047(1.20) 0.006(0.15) 0.003(0.08) 0.020(0.50) 0.012(0.30) 0.043(1.10) 0.035(0.90) 0.004(0.10) 0.000(0.00) 0.020(0.50) 0.012(0.30) 0.100(2.55) 0.089(2.25) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. O 0.019(2.00) 0.071(1.80) 1 3 2 0.118(3.00) 0.110(2.80) Dimensions in inches and (millimeters) MAXIMUM RATINGS ( @ TA = 25oC unless otherwise noted ) CHARACTERISTICS Collector-base voltage Collector-emitter voltage Emitter-base voltage Collector current-continuous Collector dissipation Junction and storage temperature o SYMBOL VCBO VCEO VEBO IC PC TJ,Tstg VALUE 50 45 5 0.5 0.3 -55 -150 UNITS V V V A W o C ELECTRICAL CHARACTERISTICS ( @ TA = 25 C unless otherwise noted ) CHARACTERISTICS Collector-base breakdown voltage (IC= 10mA, IE=0) Collector-emitter breakdown voltage (IC= 10mA, IB=0) Emitter-base breakdown voltage (IE= 1mA, IC=0) Collector cut-off current (VCB= 45V, IE=0) Emitter cut-off current (VEB= 4V, IC=0) DC current gain (VCE= 1V, IC= 100mA) Collector-emitter saturation voltage (IC= 500mA, IB= 50mA) Base-emitter saturation voltage (IC= 500mA, IB= 50mA) Base-emitter voltage (VCE= 1V, IC= 500mA) Collector capactiance (VCB=10V, f = 1MHz) Transition frequency (VCE= 5V, IC= 10mA, f= 100MHZ) MARKING: B C817-16---6A; SYMBOL VCBO VCEO VEBO ICBO IEBO hFE(1) VCE(sat) VBE(sat) VBE(ON) 100 BC817-16 BC817-25 BC817-40 BC817-16 BC817-25 BC817-40 MIN. 50 45 5 160 10 100 BC817-40---6C 2007-3 250 250 MAX. 0.1 0.1 400 0.7 1.2 1.2 600 UNITS V V V mA mA V V V pF MHZ Cob fT BC817-25---6B; RATING AND CHARACTERISTICS CURVES ( BC817-16/-25/-40 ) VCE(SAT), COLLECTOR-EMITTER VOLTAGE (V) 500 VCE=5.0V 0.6 0.5 0.4 0.3 0.2 0.1 0 b = 10 hFE , TYPICAL PULSE CURRENT GAIN 400 125 C O 25OC 125OC 300 25OC 200 -40OC -40OC 100 0 0.001 0.01 0.1 1 2 0.01 0.1 IC, COLLECTOR CURRENT (A) 1 3 VBESAT, BASE-EMITTER VOLTAGE (V) 1.2 1.0 0.8 0.6 0.4 0.2 1 b = 10 VBE(ON), BASE-EMITTER ON VOLTAGE (V) Figure1. TYPICAL PULSE CURRENT GAIN vs. COLLECTOR CURRENT IC, COLLECTOR CURRENT (A) 1 Figure2. COLLECTOR-EMITTER SATURATION VOLTAGE vs.COLLECTOR CURRENT VCE= 5V 0.8 -40 C 25 C O O -40OC 0.6 125 C O 25OC 125OC 0.4 CCB, COLLECTOR-BASE CAPACITANCE (pF) Figure3. BASE-EMITTER STURATION VOLTAGE vs. COLLECTOR CURRENT 100 Ic,COLLECTOR CURRENT(mA) 10 100 1000 0.2 0.001 40 Figure4. BASE-EMITTER ON VOLTAGE vs. COLLECTOR CURRENT Ic, COLLECTOR CURRENT (A) 0.01 0.1 1 ICBO, COLLECTOR CURRENT (nA) VCB= 40V 10 30 1 20 0.1 10 0.01 25 50 75 100 125 150 0 Figure5. COLLECTOR-CUT OFF CURRENT vs. COLLECTOR CURRENT TA, AMBIENT TEMPERATURE (OC) 0 4 Figure6. COLLECTOR-BASE CAPACITANCE vs. COLLECTOR-BASE VOLTAGE VCB, COLLECTOR-BASE VOLTAGE (V) 8 12 16 20 24 28 RATING AND CHARACTERISTICS CURVES ( BC817-16/-25/-40 ) 500 VCE=10V 350 hFE, GAIN BANDWIDTH PRODUCT (MHz) 400 PD, POWER DISSIPATION (mW) 300 250 200 150 100 50 0 300 200 100 0 1 10 100 1000 0 25 50 75 100 125 150 Figure7. GAIN BANDWIDTH PRODUCT vs. COLLECTOR CURRENT IC, COLLECTOR CURRENT (mA) TEMPERATURE (OC) Figure8. POWER DISSIPATION vs. AMBIENT TEMPERATURE DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.