FM180L

SURFACE MOUNT SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 to 200 Volts CURRENT 1.0 Ampere FEATURES * * * * * * FM120L THRU FM1200L Low switching noise L ow forward voltage drop H igh current capability High s witching capability H igh surge capabitity High r eliability SMAL MECHANICAL DATA * * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 9 4V-O Lead: MIL-STD-202E method 208C guaranteed Metallurgically bonded construction Mounting position: Any Weight: 0.09 g ram 0.067 (1.70 ) 0.051 (1.29 ) 0.110 ( 2.79 ) 0.086 ( 2.18 ) 0.180 ( 4.57 ) 0.160 ( 4.06 ) 0.012 ( 0.305 ) 0.006 ( 0.152 ) 0.067 ( 1.70 ) 0.063 ( 1.60 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 0.059 ( 1.50 ) 0.035 ( 0.89 ) 0.008 ( 0.203 ) 0.004 ( 0.102 ) 0.209 ( 5.31 ) 0.185 ( 4.70 ) Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at Derating C ase Te mperature Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 1) Typical Thermal Resistance (Note 1) Typical Junction Capacitance (Note 2) Operating Te mperature Ran g e Storage Temperature R an g e SYMBOL FM120L FM130L FM140L FM150L FM160L FM180L FM1100L VRRM VRMS VDC IO I FSM RqJA RqJL CJ TJ T STG 20 14 20 30 21 30 40 28 40 50 35 50 60 42 60 1.0 40 85 25 110 150 -55 to + 150 80 56 80 100 70 100 FM1150L FM1200L UNITS 150 105 150 200 140 200 Volts Volts Volts Amps Amps 0 0 C/W C/W pF 0 0 C C E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC Maximum Average Reverse Current at Rated DC Blocking Voltage @T A = 25 o C @T A = 1 00 o C SYMBOL FM120L FM130L FM140L FM150L FM160L FM180L FM1100L VF IR .55 .70 0.2 2 FM1150L FM1200L UNITS .85 Volts mA mA 2006-11 NOTES : 1. Thermal Resistance : Mounted on PCB. 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. Also available in SMBL. 4. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. RATING AND CHARACTERISTICS CURVES ( FM120L THRU FM1200L ) INSTANTANEOUS FORWARD CURRENT, (mA) AVERAGE FORWARD CURRENT, (A) 1.0 Single Phase Half Wave 60Hz Inductive Load FM 12 100 10 1.0 0.1 0.01 T A = 2 5 OC TA = 100 OC 0.75 FM1 50L ~F M 0L ~F M1 40 L 0.50 120 0L 0.25 T A = 7 5 OC P.C.B. Mounted on 0.4X0.4"(10X10mm) copper pad areas 0 0 25 50 75 100 125 O 150 175 0.001 0 FM120L~FM140L FM150L~FM1200L 20 40 60 80 100 120 140 CASE TEMPERATURE, ( C) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS REVERSE CURRENT, (A) 10 FM120L~FM140L CJ, JUNCTION CAPACITANCE, (pF) 20 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 400 200 100 80 60 40 20 10 FIG.2 TYPICAL REVERSE CHARACTERISTICS T J = 2 5 OC 1.0 FM180L~FM1200L FM150L~FM160L T J = 2 5 OC Pulse width=300mS 1% Duty Cycle 0.1 0.1 0.3 0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9 2.1 0.1 0.4 1.0 4 10 40 80 INSTANTANEOUS FORWARD VOLTAGE, (V) REVERSE VOLTAGE, (V) FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) FIG.4 TYPICAL JUNCTION CAPACITANCE 50 40 30 20 10 0 1 8.3mS Single Half Sine-Wave JEDEC Method 2 4 6 8 10 20 40 80 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Mounting Pad Layout 0.094 MAX. (2.38 MAX.) 0.060MIN. ( 1.52 MIN.) 0.052 MAX. (1.32 MAX.) 0.220 (5.58) REF Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.