FM4935W

RECTRON SEMICONDUCTOR TECHNICAL SPECIFICATION FM4933W THRU FM4937W SURFACE MOUNT FAST RECOVERY SILICON RECTIFIER VOLTAGE RANGE 50 to 600 Volts CURRENT 1.0 Ampere FEATURES * * * * * Ideal for surface mounted applications Low leakage current Metallurgically bonded construction Mounting position: Any Weight: 0.057 gram SMX MECHANICAL DATA * E poxy : Device has UL flammability classification 94V-0 .209 (5.31) .185 (4.70) .110 (2.79) .086 (2.18) .091 (2.31) .067 (1.70) .071 (1.80) .051 (1.30) .010 (0.25) .008 (0.20) .011 (0.28) .007 (0.18) .180 (4.57) .160 (4.06) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) .059 (1.50) .035 (0.89) MAXIMUM RATINGS ( At T A = 2 5oC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 5 5 o C Peak Forward Surge Current IFM (surge): 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Maximum Thermal Resistance Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Forward Voltage at 1.0A DC Maximum Full Load Reverse Current,Full cycle Average at TA = 55oC Maximum Average Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 4) @T A = 2 5 o C @T A = 1 25 o C SYMBOL VF IR trr FM4933W FM4934W FM4935W 1.2 50 5.0 100 200 FM4936W FM4937W UNITS Volts uAmps uAmps uAmps nSec 2005-11 REV:O SYMBOL VRRM VRMS VDC IO I FSM (Note 3) R θ JA (Note 2) R θ JC CJ T J , T STG FM4933W 50 35 50 FM4934W 100 70 100 FM4935W 200 140 200 1.0 30 30 70 15 -55 to + 150 FM4936W 400 280 400 FM4937W 600 420 600 UNITS Volts Volts Volts Amps Amps 0 0 C/ W C/ W pF 0 C NOTES : 1. Measured at 1.0 MHz and applied average voltage of 4.0VDC 2. Thermal resistance junction to case. 3. Thermal resistance junction to ambient, 6.0mm2 copper pads to each terminal. 4. Test Conditions: IF = 1.0A, V R = 30V. 5 .“Fully ROHS compliant”, “100% Sn plating (Pb-free)”. RATING AND CHARACTERISTIC CURVES ( FM4933W THRU FM4937W ) INSTANTANEOUS REVERSE CURRENT, (uA)AVERAGE FORWARD CURRENT, (A) FORWARD SURGE CURRENT, (A) FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 1.0 .8 .6 .4 .2 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE, ( ) Single Phase Half Wave 60Hz Resistive or Inductive Load 50 40 30 20 10 FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 8.3ms Single Half Sine-Wave (JEDED Method) 0 1 2 4 6 8 10 20 40 6080 100 NUMBER OF CYCLES AT 60Hz 10 4 1.0 .4 .1 .04 INSTANTANEOUS FORWARD CURRENT, (A) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 20 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS TJ = 25 Pulse Width = 300us 1% Duty Cycle TJ = 100 1.0 TJ = 25 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) .1 FIG. 5 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 8 115Va 10K 60Hz 2W 7 6 C.P.CLARE HPG 1002 5 4 1 AMP SLO-BLO FUSE C1 1.0uF 300V 1 2 3.8uH 3 /1.4 30 50W NON-INDUCTIVE UNIT UNDER TEST 1.0 Adc FROM CONSTANT R2 VOLTAGE SUPPLY C1 1 RIPPLE = 3mVrms MAX 1.0uF 10W 300V NONINDUCTIVE Zout 11/2 MAX DC to 2kHz % CARBON CORE FOR RECTIFIER .01 .6 .8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 6 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) 30 Vdc CONSTANT VOLTAGE SUPPLY 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 REVERSE VOLTAGE, ( V ) 100 TJ = 25 MINIMIZE ALL LEAD LENGTHS A-TEKTRONIX 545A. K PLUG IN PRE AMP P6000 PROBE OR EQUIVALENT R2-TEN-1W 10 IN PARALLEL R1-ADJUSTED FOR 1.4£[ BETWEEN POINT 2 OF RELAY AND RECTIFIER 10 TA = 25 INDUCTIVE = 3.8uH 0 trr IFM 1.0 i(t) di/dt = 50A/uS 0 IRM (REC) SET TIME BASE FOR 50/100 ns/cm RECTRON Mounting Pad Layout 0.094 MAX. (2.38 MAX.) 0.071 MIN. (1.80 MIN.) 0.052 MIN. (1.32 MIN.) 0.220 (5.58) REF Dimensions in inches and (millimeters) RECTRON