FM805P

FM801P THRU FM807P SURFACE MOUNT GLASS PASSIVATED SILICON RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 8.0 Ampere FEATURES * * * * Ideal for SMT Mounting High Forward Surge Capability Low Forward Voltage Drop Excellent High Temperature Stability Top View Bottom View DO-277 MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O * Weight: 0.086 grams (approximate) * Halogen-free MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. resistive or inductive load. Dimensions in millimeters MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL FM801P FM803P FM804P FM805P FM806P FM807P UNITS Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 70 140 280 420 560 700 Volts VDC 50 100 200 400 600 800 1000 Volts RATINGS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T C =95 OC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) FM802P IO 8.0 Amps I FSM 200 Amps 2 165.9 A /Sec I t Current Squarad Time Operating Temperature Range TJ Storage Temperature Range T STG 2 150 0 C -55 to + 150 0 C ELECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 8.0A DC Maximum Average Reverse Current @T A = 25 o C at Rated DC Blocking Voltage @T A = 100 o C SYMBOL FM801P VF IR NOTES : 1. Thermal Resistance : Mounted on PCB. 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. 4. Test Conditions: IF= 0.5A, IR= -1.0A, IRR= -0.25A. 5. Available in Halogen-free epoxy by adding suffix -HF after the part nbr. FM802P FM803P FM804P 1.1 5 FM805P FM806P FM807P UNITS Volts uAmps 150 2018-03 REV: A AVERAGE FORWARD CURRENT, (A) 10 8 6 4 Single Phase Half Wave 60 Hz Inductive or Resistive Load 2 0 0 50 100 150 INSTANTANEOUS FORWARD CURRENT, (A) RATING AND CHARACTERISTICS CURVES ( FM801P THRU FM807P ) 40 20 10 4 1.0 0.4 T A = 25 OC Pulse Width = 300mS 1% Duty Cycle 0.1 0 O CASE TEMPERATURE, ( C) 10000 1000 TA = 100 OC 100 10 TA = 25 OC 0 20 40 60 80 1.0 1.5 2.0 2.5 3.0 3.5 FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (uA) FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 1.0 0.5 INSTANTANEOUS FORWARD VOLTAGE, (V) 100 120 140 PERCENT RATED PEAK REVERSE VOLTAGE, (%) FIG.3 TYPICAL REVERSE CHARACTERISTICS 200 8.3mS Single Half Sine-Wave JEDEC Method 190 180 170 160 150 140 100 1 7 10 19 50 60 100 NUMBER OF CYCLES AT 60Hz FIG.4 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT Marking Description Cathode Band Rectron Logo Part No. ^ ----- for all Voltage range 8A^ V Y WW Week – code BOTTOMSIDE HEAT SINK (WW: 01~52 ) Note: Pins Left & Right must be electrically connected at the printed circuit board. LEFT PIN RIGHT PIN Year - code (Y: Last digit of year A:2010, B:2011...) Recommendation of Mounting Pad Layout Z C E1 X2 X1 Y Y1 Dimensions Z X1 X2 Y1 Y C E1 Dimensions in millimeters Value (in mm) 6.6 1.4 3.6 0.8 4.7 3.87 0.9 REEL TAPING SPECIFICATIONS FOR SURFACE MOUNT DEVICES-FLAT MELF ( DO-277 ) P0 P1 d E F B A P o T W MAX. 3 A R o MAX. 3 W1 D C Fig.: Configuration of FLAT MELF TAPING (DO-277) ITEM Carrier width Carrier length Carrier depth Sprocket hole SYMBOL A B C d Reel outside diameter Reel inner diameter Feed hole diameter Strocket hole position Punch hole position Punch hole pitch D D1 D2 E F P Sprocket hole pitch Embossment center Totall tape thickness Tape width Reel width P0 P1 T W W1 D1 D2 DO-277 mm(inch) 5.45 0.1(0.179 0.004) 6.80 0.1 (0.268 0.004) 1.33 0.1 (0.052 0.004) 1.5 0.1 (0.059 0.004) 178 2.0 (7.0 50 Min. 13 0.5 (0.512 1.75 0.1 (0.069 5.50 0.05 (0.217 8.0 0.1 (0.315 4.0 0.1 (0.157 0.079) 0.020) 0.004) 0.002) 0.004) 0.004) 2.00 0.05 (0.079 0.002) 0.28 0.02 (0.011 0.001) 12.00 0.1 (0.472 12.00 0.3 (0.472 0.012) 16.8 2.0 (0.661 0.079) Note: 1.Devices are packed in accordance with EIA standard RS-481-A and specification given above. 2.Available on 7 inch ( 1500 ct. ) or 13 inch ( 5000 ct. ) diameter reels. 0.004) 1. REEL D Packing D Code (mm) -T 178 -W 330 Packing L W H Code (mm) (mm) (mm) -T 390 205 310 -W 355 360 350 2. CARTON PACKAGING OF DIODE AND BRIDGE RECTIFIERS REEL PACK PACKAGE DO-277 PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX -T/W 5,000 10,000 --- --- 330 360*355*360 80,000 15.29 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.