FM807C

FM807C GLASS PASSIVATED SILICON RECTIFIER VOLTAGE 1000 Volts CURRENT 8.0 Amperes FEATURES * Low leakage * Low Forward voltage drop * High current capability * High surge capability * High reliability * P/N suffix V means AEC-Q101 qualified, e.g:FM807CV * Halogen-free MECHANICAL DATA * Case: Molded plastic * Weight: 0.24 gram DO-214AB 0.125 (3.17 ) 0.245 ( 6.22 ) 0.115 (2.92 ) 0.220 ( 5.59 ) 0.280 ( 7.11 ) 0.260 ( 6.60 ) 0.012 ( 0.305 ) 0.006 ( 0.152 ) 0.103 ( 2.62 ) 0.079 ( 2.06 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS 0.060 ( 1.52 ) 0.008 ( 0.203 ) 0.004 ( 0.102 ) 0.030 ( 0.76 ) Ratings at 25 o C ambient temperature unless otherwise specified. 0.320 ( 8.13 ) 0.305 ( 7.75 ) Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RATINGS (@ TA=25 OC unless otherwise noted) SYMBOL FM807C UNITS Maximum Recurrent Peak Reverse Voltage VRRM 1000 Volts Maximum RMS Voltage VRMS 700 Volts VDC 1000 Volts IO 8.0 Amps I FSM 300 Amps A Sec RATINGS Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T C=95 OC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) 2 2 Typical Current Squarad Time I t 373.5 Operating Temperature Range TJ -55 to + 150 0 C T STG -55 to + 150 0 C Storage Temperature Range ELECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 8.0A DC Maximum Average Reverse Current @T A = 25 o C at Rated DC Blocking Voltage @T A = 150 o C SYMBOL FM807C UNITS VF 1.05 Volts 0.3 uA 500 uA IR NOTE : "ROHS compliant”, 2018-12 REV: B AVERAGE FORWARD CURRENT, (A) 10 8 6 4 Single Phase Half Wave 60 Hz Inductive or Resistive Load 2 0 0 50 100 150 INSTANTANEOUS FORWARD CURRENT, (A) RATING AND CHARACTERISTICS CURVES ( FM807C) 40 20 10 4 1.0 0.4 T A = 25 OC Pulse Width = 300mS 1% Duty Cycle 0.1 0 0.5 O CASE TEMPERATURE, ( C) 1000 100 O C 10 1.0 TA = 25 OC 0 20 40 60 80 100 1.5 2.0 2.5 3.0 3.5 FIG.2 MAXIMUM INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (uA) FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE TA =150 1.0 INSTANTANEOUS FORWARD VOLTAGE, (V) 120 140 PERCENT RATED PEAK REVERSE VOLTAGE, (%) FIG.3 MAXIMUM REVERSE CHARACTERISTICS 300 250 10mS Single Half Sine-Wave JEDEC Method 200 150 100 50 10 1 10 11 19 50 60 NUMBER OF CYCLES AT 60Hz FIG.4 MAXIMUM NON-REPETITIVE FORWAR RD SURGE CURRENT 100 Mounting Pad Layout 0.185 MAX. (4.69 MAX.) 0.121MIN. (3.07 MIN.) 0.060 MIN. (1.52 MIN.) 0.320 (8.127 ) REF Dimensions in inches and (millimeters) Marking Description Rectron Logo 8A7 V Y W W H Part No. Voltage-code 7-------1000V Cathode Band Halogen-free Year – code (Y: Last digit of year & A:2010,B:2011......) Week – code (WW:01~52) REEL TAPING SPECIFICATIONS FOR SURFACE MOUNT DEVICES-FLAT MELF ( SMA/SMB/SMC ) P0 P1 d E F B A P o T W MAX. 3 A D1 D2 o MAX. 3 R W1 D C Fig.: Configuration of FLAT MELF TAPING (SMA/SMB/SMC) ITEM Carrier width Carrier length Carrier depth Sprocket hole SYMBOL A B C d DO214AC (SMA) mm(inch) 2.6 0.15 (0.102 0.006) 5.15 0.15 (0.203 0.006) 2.3 0.15 (0.091 0.006) 1.5 0.1 (0.059 0.004) DO214AA (SMB) mm(inch) 3.65 0.1 (0.144 0.004) 5.69 0.1 (0.224 0.004) 2.67 0.1 (0.105 0.004) 1.5 0.1 (0.059 0.004) Reel outside diameter Reel inner diameter Feed hole diameter Strocket hole position Punch hole position Punch hole pitch D D1 D2 E F P 178 2.0 (7.0 0.079) 50 Min. 13 13 0.5 (0.512 0.020) 1.5 1.5 0.1 (0.059 0.004) 5.65 0.05 (0.222 0.002) 5.65 4.0 0.1 (0.157 0.004) 8.0 Sprocket hole pitch Embossment center Totall tape thickness Tape width Reel width P0 P1 T W W1 4.0 0.1 (0.157 2.0 0.1 (0.079 0.30 0.05 (0.012 12.0 0.2 (0.472 16.8 2.0 (0.661 178 0.004) 0.004) 0.002) 0.008) 0.079) 2.0 (7.0 0.079) DO214AB (SMC) mm(inch) 6.0 0.1 (0.236 0.004) 8.30 0.1 (0.327 0.004) 2.5 0.1 (0.098 0.004) 1.5 0.1 (0.059 178 0.004) 0.079) 50 Min. 50 Min. 13 0.5 (0.512 0.020) 0.5 (0.512 0.020) 0.1 (0.059 0.004) 1.5 0.1 (0.059 0.004) 0.05 (0.222 0.002) 7.65 0.05 (0.301 0.002) 8.0 0.1 (0.315 0.004) 0.1 (0.315 0.004) 4.0 2.0 0.1 (0.157 0.004) 0.1 (0.079 0.004) 0.6 Max. 12.0 0.2 (0.472 0.008) 16.8 2.0 (0.661 0.079) 4.0 4.0 0.1 (0.157 0.004) 0.1 (0.157 0.004) 0.6 Max. 16.0 0.2 (0.630 0.008) 24.0 2.0 (0.945 0.079) Note: 1.Devices are packed in accordance with EIA standard RS-481-D and specification given above. 2.Available on 7 inch ( 1500 ct. ) or 13 inch ( 5000 ct. ) diameter reels. D5 2.0 (7.0 Visit http:// www.rectron.com for complete datasheets PACKAGING OF DIODE AND BRIDGE RECTIFIERS REEL PACK PACKAGE SMC PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX -W/-T 3,000 3,000 --- --- 330 360*355*360 24,000 11.50 Revise History Rev Content Data B Added Halogen-free and Modify IR 2018-12-08 DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.