FR605-T

FR601 THRU FR607 FAST RECOVERY RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 6.0 Amperes FEATURES * * * * * * Fast switching Low leakage Low forward voltage drop High current capability High currenf surge High reliability MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 2.08 grams 1.0 (25.4) MIN. .052 (1.3) DIA. .048 (1.2) .360 (9.1) .340 (8.6) .360 (9.1) DIA. .340 (8.6) 1.0 (25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS o Ratings at 25 C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) o MAXIMUM RATINGS (At T A = 25 C unless otherwise noted) SYMBOL FR601 FR602 FR603 FR604 FR605 FR606 FR607 UNITS Maximum Recurrent Peak Reverse Voltage RATINGS VRRM 50 100 200 400 600 800 1000 Volts Maximum RMS Voltage VRMS 35 50 70 100 140 200 280 400 420 600 560 800 700 1000 Volts VDC Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 75 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Current Squared Time IO 6.0 Amps I FSM 300 Amps 2 374 2 AS CJ 150 pF T J , T STG -55 to + 150 IT Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range Volts 0 C o ELECTRICAL CHARACTERISTICS (At TA = 25 C unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 6.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 25 oC Maximum Full Load Reverse Current Average, Full Cycle .375” (9.5mm) lead length at T L = 55 oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts SYMBOL VF FR601 FR602 FR603 FR604 1.3 FR605 FR606 FR607 uAmps 10 IR trr 150 150 UNITS Volts uAmps 250 500 nSec 2109-09 REV: C FIG. 1 - TYPICAL FORWARD CURRENT DERATING CURVE 8 6 4 Single Phase Half Wave 60Hz Resistive or Inductive Load 2 0 0 25 FIG. 2 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) AVERAGE FORWARD CURRENT, (A) RATING AND CHARACTERISTIC CURVES ( FR601 THRU FR607 ) 50 75 100 125 150 AMBIENT TEMPERATURE, ( ) 600 8.3ms Single Half Sine-Wave (JEDED Method) 500 400 300 200 100 0 175 1 10 50 NUMBER OF CYCLES AT 60Hz 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD FIG. 4 - TYPICAL JUNCTION CAPACITANCE CHARACTERISTICS 200 500 100 40 10 TJ = 25 Pulse Width=300uS 1% Duty Cycle 1 0 .6 .8 1.0 1.2 1.4 1.6 1.8 100 JUNCTION CAPACITANCE, (pF) INSTANTANEOUS FORWARD CURRENT, (A) 1000 60 40 20 10 TJ = 25 6 4 2 1 2.0 .1 .2 INSTANTANEOUS FORWARD VOLTAGE, (V) .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) FIG. 5 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE (+) 25 Vdc (approx) (-) 10 NONINDUCTIVE +0.5A (-) D.U.T PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE trr OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 1cm SET TIME BASE FOR 50/1 ns/cm RECTRON 40 100 AXIAL LEAD TAPING SPECIFICATIONS FOR RECTIFIERS Axial lead devices are packed in accordance with EIA standard RS-296-D and specifications given below. COMPNENT OUTLINE COMPONENT PITCH A 0.5mm (.020") T-1 R-1 5.0mm 5.0mm INNER TAPE PITCH B 0.5mm (.020") 1.5mm (.059") CUMULATIVE PITCH TOLERANCE 26.0mm 26.0mm 2.0mm/20pitch 2.0mm/20pitch R-1 5.0mm A-405 A-405 DO-41 DO-41 DO-15 R-3 DO-201AD 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 5.0mm 10.0mm 52.4mm 2.0mm/20pitch R-6 10.0mm 52.4mm 2.0mm/10pitch 1.5KE 10.0mm 52.4mm 2.0mm/10pitch 26.0mm 2.0mm/20pitch 2.0mm/20pitch 2.0mm/20pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 2.0mm/10pitch 52.4mm 26.0mm 52.4mm 52.4mm 52.4mm 52.4mm Note: -E for 26mm inner tape pitch -F & -T for 52mm inner tape pitch Z O O 90 5 DO A E W L1 D1 B L2 D T E Fig.: Configuration of AXIAL LEAD TAPING ITEM Component alignment Tape width Exposed adhesive Body eccentricity Reel outside diameter Reel inner diameter Feed hole diameter Reel width Notes : SYMBOL Z T E IL1-L2I D D1 DO W SPECIFICATIONS (mm) 1.2 Max. 6.0 0.4 0.8 Max. 1.0 Max. 330.0 85.7 0.3 30.5 0.4 79.0 1.0 1.Each component lead shall be sandwiched between tapes for a minimum of 3.2mm (0.126"). 2.The reel width "W" for 26mm taping is 50.0 1.0mm (1.97" 0.040"). SPECIFICATIONS (inch) 0.048 Max. 0.236 0.016 0.032 Max. 0.040 Max. 13.0 3.375 0.012 1.201 0.016 3.110 0.040 2002-12 RECTRON Attachment information about FR60X 1. Internal Circuit Anode Cathode 2. Marking on the body Cathode Band Plant - code Rectron Logo Part No. V X F R 6 0 X X Year – code (Y: Last digit of year & A:2010,B:2011……) Month – code (M:0~9,O,N,D) Voltage-code 1-------50V 2-------100V 3-------200V 4-------400V 5-------600V 6-------800V 7------1000V PACKAGING OF DIODE AND BRIDGE RECTIFIERS BULK PACK PACKAGE PACKING CODE R-6/R-7 -B EA PER BOX INNER BOX SIZE (mm) 200 300*73*40 CARTON SIZE EA PER CARTON (mm) GROSS WEIGHT(Kg) 347*320*271 12.93/14.57 4,800 REEL PACK PACKAGE R-6/R-7 PACKING EA PER EA PER COMPONENT TAPE SPACE REEL DIA CARTON SIZE EA PER GROSS SPACE INNER REEL CARTON WEIGHT(Kg) CODE (mm) (mm) (mm) (mm) BOX -T 800 9.5 800 52 330 355*350*335 3,200 9.72/9.91 AMMO PACK PACKAGE PACKING CODE R-6/R-7 -F REEL ( EA ) 300 COMPONENT TAPE SPACE SPACE(mm) (mm) 9.5 52 BOX SIZE (mm) CARTON SIZE(mm) 255*73*100 400*268*225 CARTON ( EA ) 3,000 GROSS WEIGHT (Kg) 8.5/8.7 RECTRON Attachment information about FR60X 5. Items marked on the reel box and carton 5.1 On the reel (for –T) CUSTOMER TYPE QUANTITY LOT NO. Q.A. REMARK 5.2 On the box (for –E & -F) TYPE QUANTITY LOT NO. Q.A. 5.3 On the carton CUSTOMER TYPE QUANTITY LOT NO. REMARK DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.