HFM208W

RECTRON SEMICONDUCTOR TECHNICAL SPECIFICATION HFM201W THRU HFM208W SURFACE MOUNT HIGH EFFICIENCY SILICON RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 2.0 Amperes FEATURES * * * * * Ideal for surface mounted applications Low leakage current Metallurgically bonded construction Mounting position: Any Weight: 0.098 gram .220 (5.59) .205 (5.21) .155 (3.94) .130 (3.30) .096 (2.44) .084 (2.13) .083 (2.11) .077 (1.96) .010 (0.25) .008 (0.20) UNITS Volts Volts Volts Amps Amps 20 -55 to + 150 pF 0 MECHANICAL DATA * Epoxy : Device has UL flammability classification 94V-0 .012 (0.305) .006 (0.152) .180 (4.57) .160 (4.06) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .060 (1.52) .030 (0.76) Dimensions in inches and (millimeters) MAXIMUM RATINGS (At TA = 25oC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Volts Maximum DC Blocking Voltage Maximum Average Forward Current at TA = 50oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range SYMBOL VRRM VRMS VDC IO IFSM CJ TJ, TSTG 30 HFM201W HFM202W HFM203W HFM204W HFM205W HFM206W HFM207W HFM208W 50 35 50 100 70 100 200 140 200 300 210 300 400 280 400 2.0 60 600 420 600 800 560 800 1000 700 1000 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Forward Voltage at 2.0A DC Maximum Full Load Reverse Current, Full cycle Average TA = 55oC Maximum DC Reverse Current at @TA = 25oC Rated DC Blocking Voltage @TA = 125oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF=0.5A, IR=-1.0A, IRR=-0.25A. 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts. SYMBOL VF IR trr 50 HFM201W HFM202W HFM203W HFM204W HFM205W HFM206W HFM207W HFM208W UNITS Volts uAmps uAmps uAmps 1.0 1.3 50 5.0 100 1.7 75 nSec 2002-11 RATING AND CHARACTERISTIC CURVES ( HFM201W THRU HFM208W ) AVERAGE FORWARD CURENT, (A) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 4.0 Single Phase Half Wave 60Hz Resistive or Inductive Load (+) 25 Vdc (approx) (-) D.U.T 0 PULSE GENERATOR (NOTE 2) -0.25A 2.0 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES:1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 1cm SET TIME BASE FOR 10/20 ns/cm 0 0 25 50 75 100 125 150175 AMBIENT TEMPERATURE ( ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, (uA) INSTANTANEOUS FORWARD CURRENT, (A) 100 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS M2 0 HF W~ 04 M2 HF W 5W FM ~H 01W M2 1.0 .1 TJ = 25 HF .1 .01 Pulse Width = 300uS 1% Duty Cycle .01 .001 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 140 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 6 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) PEAK FORWARD SURGE CURRENT, (A) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 70 60 50 40 30 20 10 0 1 2 5 10 20 50 NUMBER OF CYCLES AT 60Hz 100 8.3ms Single Half Sine-Wave (JEDEC Method) 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, ( V ) HFM 206 HFM HF M2 TJ = 100 TJ = 25 06 201 W~ W ~H HFM FM 20 10 TJ = 150 1.0 203 8W 205 W TJ = 25 W~H FM2 08W RECTRON Mounting Pad Layout 0.106 MAX. (2.69 MAX.) 0.083 MIN. (2.10 MIN.) 0.050 MIN. (1.27 MIN.) 0.220 REF Dimensions in inches and (millimeters) RECTRON