HFM305L

VOLTAGE RANGE 50 to 1000 Volts CURRENT 3.0 Ampere FEATURES * * * * * * G lass passivated device I deal for surface mounted applications L ow leakage current M etallurgically bonded construction M ounting position: Any W eight: 0 . 24 g ram SURFACE MOUNT GLASS PASSIVATED HIGH EFFICIENCY SILICON RECTIFIER HFM301L THRU HFM308L SMCL MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O 0.125 (3.17 ) 0.115 (2.92 ) 0.245 ( 6.22 ) 0.220 ( 5.59 ) 0.280 ( 7.11 ) 0.260 ( 6.60 ) 0.012 ( 0.305 ) 0.006 ( 0.152 ) 0.085 ( 2.15 ) 0.061 ( 1.55 ) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 0.060 ( 1.52 ) 0.030 ( 0.76 ) 0.008 ( 0.203 ) 0.004 ( 0.102 ) 0.320 ( 8.13 ) 0.305 ( 7.75 ) Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 5 0 OC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 1) Typical Thermal Resistance (Note 1) Typical Junction Capacitance (Note 2) Operating Te mperature Ran g e Storage Temperature R an g e SYMBOL HFM301L HFM302L HFM303L HFM304L HFM305L VRRM VRMS VDC IO I FSM RqJL RqJA CJ TJ T STG 70 150 -55 to + 150 200 15 60 50 50 35 50 100 70 100 200 140 200 300 210 300 3.0 150 400 280 400 HFM306L HFM307L HFM308L UNITS 600 420 600 800 490 800 1000 700 1000 Volts Volts Volts Amps Amps 0 0 C/W C/W pF 0 0 C C ELECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 3.0A DC Maximum Full Load Reverse Current, Full cycle Average T A = 55 OC Maximum Average Reverse Current at Rated DC Blocking Voltage @T A = 2 5 o C @T A = 1 25 o C trr 50 SYMBOL HFM301L HFM302L HFM303L HFM304L HFM305L VF IR 1.0 1.3 50 2 150 75 HFM306L HFM307L HFM308L UNITS 1.7 Volts mA mA mA nSec 2006-12 Maximum Reverse Recovery Time (Note 4) NOTES : 1 . Thermal Resistance : Mounted on PCB. 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. 4. Test Conditions: IF= 0.5A, IR= -1.0A, IRR= -0.25A. RATING AND CHARACTERISTICS CURVES ( HFM301L THRU HFM308L ) 50 W NONINDUCTIVE 10 W NONINDUCTIVE +0.5A trr (+) 25 Vdc (approx) (-) D.U.T (-) PULSE GENERATOR (NOTE 2) 0 -0.25A 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) NOTES: 1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. -1.0A 1cm SET TIME BASE FOR 50/100 ns/cm FIG.1 TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 3.0 AVERAGE FORWARD CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (mA) 1000 TA = 125 OC 2.5 2.0 1.5 1.0 0.5 Single Phase Half Wave 60Hz Resistive or Inductive Load 100 10 T A = 7 5 OC 1.0 T A = 2 5 OC 0 25 50 75 100 125 150 175 0.1 0 20 40 60 80 100 120 140 AMBIENT TEMPERATURE, (OC) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.2 TYPICAL FORWARD CURRENT DERATING CURVE FIG.3 TYPICAL REVERSE CHARACTERISTICS RATING AND CHARACTERISTICS CURVES ( HFM301L THRU HFM308L ) INSTANTANEOUS FORWARD CURRENT, (A) PEAK FORWARD SURGE CURRENT, (A) 20 10 3.0 1.0 0.3 0.1 0.03 0.01 0 200 150 125 100 T J = 2 5 OC HFM306L~HFM308L HFM304L~HFM305L 8.3ms Single Half Sine-Wave (JEDED Method) 50 30 20 10 HFM306L~HFM308L HFM301L~HFM306L HFM301L~HFM303L Pulse Width=300uS 1% Duty Cycle 0.5 1.0 1.5 2.0 2.5 3.0 3.5 1 5 10 50 100 INSTANTANEOUS FORWARD VOLTAGE, (V) NUMBER OF CYCLES AT 60Hz FIG.4 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 200 JUNCTION CAPACITANCE, (pF) HFM301L~HFM305L FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 60 40 20 10 6 4 2 1 0.1 0.2 T J = 2 5 OC HFM306L~HFM308L 0.4 1.0 2 4 10 20 40 100 REVERSE VOLTAGE, (V) FIG.6 TYPICAL JUNCTION CAPACITANCE Mounting Pad Layout 0.185 MAX. (4.69 MAX.) 0.121MIN. ( 3.07 MIN.) 0.060 MAX. (1.52 MAX.) 0.320 REF Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.