MMBTA42

MMBTA42 SOT-23 BIPOLAR TRANSISTORS TRANSISTOR(NPN) FEATURES * High breakdown voltage * Low collector-emitter saturation voltage * Complementary to MMBTA92 (NPN) SOT-23 MECHANICAL DATA * * * * * COLLECTOR 3 Case: Molded plastic Epoxy: UL 94V-O rate flame retardant Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.008 gram 1 BASE 2 EMITTER 0.006(0.15) 0.003(0.08) 0.055(1.40) 0.047(1.20) 0.043(1.10) 0.035(0.90) 0.020(0.50) 0.012(0.30) 0.004(0.10) 0.000(0.00) 0.020(0.50) 0.012(0.30) 0.100(2.55) 0.089(2.25) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 0.019(2.00) 0.071(1.80) 1 3 0.110(2.80) 2 0.118(3.00) Dimensions in inches and (millimeters) MAXIMUM RATINGS ( @ TA = 25oC unless otherwise noted ) RATINGS Collector Current-Continuous Collector Power Dissipation SYMBOL IC PC TJ TSTG VALUE 0.3 350 150 -55 to +150 UNITS A mW o o Max. Operating Temperature Range Storage Temperature Range C C ELECTRICAL CHARACTERISTICS ( @ TA = 25oC unless otherwise noted ) CHARACTERISTICS Collector-base breakdown voltage (IC=100uA,IE=0) Collector-emitter breakdown voltage (IC=1mA,IB=0) Emitter-Base breakdown voltage (IE=100uA,IC=0) Collector cut-off current (VCB=200V,IE=0) Emitter cut-off current (VEB=5V,IC=0) (VCE=10V,IC=1mA) DC current gain (VCE=10V,IC=10mA) (VCE=10V,IC=30mA) Collector-emitter saturation voltage (IC=20mA,IB=2mA) Base-emitter saturation voltage (IC=20mA,IB=2mA) Transition frequency (VCE=20V,IC=10mA,f=30MHz) Note: "Fully ROHS Complant", "100% Sn plating (Pb-free)". SYMBOL V(BR)CBO V(BR)CEO V(BR)EBO ICBO IEBO hFE(1) hFE(2) hFE(3) VCE(sat) VBE(sat) fT MIN. 300 300 5 60 100 60 50 TYP. MAX. 0.25 0.1 200 0.2 0.9 UNITS V V V uA uA V V MHz 2007-5 RATING AND CHARACTERISTICS CURVES ( MMBTA42 ) 140 hFE, DC CURRENT GAIN VCE =5V 125 C O VCESAT, COLLECTOR-EMITTER VOLTAGE (V) 0.3 0.25 0.2 0.15 0.1 0.05 0.1 b =10 120 100 80 60 40 20 0.1 25OC 125OC -40OC -40OC 25OC 1 10 100 1 10 100 IC, COLLECTOR CURRENT (mA) Figure 1 DC Current Gain vs. Collector Current 1 VBESAT, BASE-EMITTER VOLTAGE (V) Figure 2 Collector-Emitter Saturation Voltage vs. Collector Current VBE(ON), BASE-EMITTER VOLTAGE (V) IC, COLLECTOR CURRENT (mA) 1 VCE =1V 0.8 -40OC 25OC 0.6 125OC 0.4 b =10 0.8 -40OC 0.6 25 C O 125OC 0.4 0.2 0.1 1 10 100 0.2 0.1 1 10 100 IC, COLLECTOR CURRENT (mA) IC, COLLECTOR CURRENT (mA) Figure 3. Base-Emitter Saturation Voltage vs. Collector Current Figure 4 Base-Emitter ON Voltage vs. Collector Current RATING AND CHARACTERISTICS CURVES ( MMBTA42 ) 100 ICBO, COLLECTOR CURRENT (nA) VCB =150V CAPACITANCE (pF) 100 50 20 10 5 2 Ccb Ceb 10 1 25 50 75 100 125 150 1 1 10 100 1000 Figure 5 Collector-Cut off Current vs. Ambient Temperature 1 PD, POWER DISSIPATION (W) TA, AMBIENT TEMPERATURE (OC) REVERSE BIAS VOLTAGE (V) Figure 6 Collector-Base and Emitter-Base Capacitance vs. Reverse Bias Voltage 0.75 0.5 0.25 0 0 25 50 75 100 125 150 TEMPERATURE (OC) Figure 7 Power dissipation vs. Ambient Temperature DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.