RBU1006M

VOLTAGE RANGE 50 to 1000 Volts CURRENT 10.0 Ampere FEATURES * * * * * Low leakage Low forward voltage Silver-plated copper leads Surge overload rating: 200 amperes peak Mounting position: Any SINGLE-PHASE GLASS PASSIVATED SILICON BRIDGE RECTIFIER RBU1001M T HRU RBU1007M RBU .880 (22.3) .860 (21.8) .160 (4.1) .140 (3.5) .080 (2.03) .060 (1.52) .740 (18.8) .720 (18.3) .140 (3.56) .130 (3.30) MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O .512 (13.0) .085 (2.16) .075 (1.90) .710 (18.0) .690 (17.5) .050 (1.27) .040 (1.02) .210 (5.33) .190 (4.83) .080 (2.03) .065 (1.65) .022 (0.56) .018 (0.46) .100 (2.54) .085 (2.16) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T C = * 100 o C (Note 4) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 1) Operating and Storage Temperature Ran g e SYMBOL VRRM VRMS VDC IO I FSM R q JC R q JA T J, T STG RBU1001M RBU1002M RBU1003M RBU1004M RBU1005M RBU1006M RBU1007M UNITS Volts Volts Volts Amps Amps 0 50 35 50 100 70 100 200 140 200 400 280 400 10.0 200 2.3 26 -55 to + 150 600 420 600 800 560 800 1000 700 1000 C/ W 0 C E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 5.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 25 o C @T A = 1 00 o C SYMBOL VF IR RBU1001M RBU1002M RBU1003M RBU1004M RBU1005M RBU1006M RBU1007M UNITS Volts m Amps 2006-12 1.1 2.0 100 NOTES : 1 . Thermal Resistance : Heat-sink case mounted or if PCB mounted. 2. "Fully ROHS compliant", "100% Sn plating (Pb-free)". 3. Equivalent to Vishay's GBU10 Series. 4. "*" Heat Sink Temperature. RATING AND CHARACTERISTICS CURVES ( RBU1001M THRU RBU1007M ) INSTANTANEOUS FORWARD CURRENT, (A) 30 20 TC= 150 OC (TYP) TC= 25 OC (TYP) 34 30 POWER DISSIPATION, (W) sine wave TJ = 150 OC 10 5 2 1 0.5 0.2 0 0.2 0.4 0.6 0.8 1 Pulse test per one diode 20 10 1.2 1.4 1.6 0 0 2 4 6 8 10 12 14 FIG.1 TYPICAL INSTANTANEOUS FORWARD CHARACTERITICS PEAK FORWARD SURGE CURRENT, (A) INSTANTANEOUS FORWARD VOLTAGE, (V) AVERAGE RECTIFIED FORWARD CURRENT, (A) FIG.2 POWER DISSIPATION AVERAGE FORWARD CURRENT, (A) 4 on glass-epoxi substrate 300 sine wave 0 IFSM 200 8.3ms 8.3ms 3 soldering land 5mmf sine wave R-load free in air 1 cycle non-repetitive Tj=25 P.C.B 2 100 1 0 0 1 2 5 10 20 50 100 0 0 40 80 120 160 NUMBER OF CYCLE AMBIENT TEMPERATURE, (OC) FIG.3 SURGE FORWARD CURRENT CAPABILITY AVERAGE FORWARD CURRENT, (A) FIG.4 TYPICAL FORWARD CURRENT DERATING CURVE 2.4 THERMAL RESISTANCE (OC/W) with thermal compound 10 8 6 4 2 0 10 sine wave R-load on heatsink heatsink Tc Tc 2.0 1.6 1.2 0.8 0.4 0 2 30 50 70 90 110 130 150 170 3 4 5 6 7 8 FIG.5 TYPICAL FORWARD CURRENT DERATING CURVE HEAT SINK TEMPERATURE, (OC) MOUNTING TORQUE (kg.cm) FIG.6 CONTACT THERMAL RESISTANCE fcf DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.