RL101H

RECTRON SEMICONDUCTOR TECHNICAL SPECIFICATION RL101H THRU RL108H HIGH EFFICIENCY RECTIFIER VOLTAGE RANGE 50 to 1000 Volts CURRENT 1.0 Ampere FEATURES * * * * * * * Low power loss, high efficiency Low leakage Low forward voltage High current capability High speed switching High surge capability High reliability A-405 MECHANICAL DATA * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.33 gram .025 (0.6) DIA. .021 (0.5) 1.0 (25.4) MIN. .205 (5.2) .166 (4.2) .107 (2.7) .080 (2.0) DIA. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 1.0 (25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RATINGS (At T A = 25 oC unless otherwise noted) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 55 oC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Range SYMBOL VRRM V RMS VDC IO I FSM CJ T J , T STG 15 -55 to + 150 RL101H RL102H RL103H RL104H RL105H RL106H RL107H RL108H UNITS 50 35 50 100 70 100 200 140 200 300 210 300 1.0 30 12 400 280 400 600 420 600 800 560 800 1000 700 1000 Volts Volts Volts Amps Amps pF 0 C ELECTRICAL CHARACTERISTICS (At TA = 25oC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage TA = 2 5 oC Maximum Full Load Reverse Current Average, Full Cycle .375” (9.5mm) lead length at TL = 5 5oC Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = - 0.25A 2. Measured at 1 MHZ and applied reverse voltage of 4.0 volts SYMBOL VF RL101H RL102H RL103H RL104H RL105H RL106H RL107H RL108H UNITS Volts 1.0 1.3 1.7 5.0 IR 100 trr 50 75 uAmps nSec 2003-7 uAmps RATING AND CHARACTERISTIC CURVES ( RL101H THRU RL108H ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC +0.5A (-) AVERAGE FORWARD CURENT, (A) 50 NONINDUCTIVE 10 NONINDUCTIVE trr FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 2.0 Single Phase Half Wave 60Hz Resistive or Inductive Load (+) 25 Vdc (approx) (-) D.U.T 0 PULSE GENERATOR (NOTE 2) -0.25A 1.0 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. 1cm SET TIME BASE FOR 10/20 ns/cm 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS REVERSE CURRENT, (uA) INSTANTANEOUS FORWARD CURRENT, (A) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0V 10 TJ = 150 1.0 200 V 0/ 40 0/ 30 1.0 TJ = 25 .1 50 / 10 TJ = 100 .1 .01 TJ = 25 Pulse Width = 300uS 1% Duty Cycle .01 0 20 40 60 80 100 PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) 120 140 .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 1.8 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, (A) FIG. 6 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, (pF) 50 8.3ms Single Half Sine-Wave (JEDEC Method) 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 40 REVERSE VOLTAGE, ( V ) 100 TJ = 25 RL1 01H ~RL 40 30 20 10 0 1 2 20 40 4 6 8 10 NUMBER OF CYCLES AT 60Hz 100 60 0 /8 00 105 /1 00 0V H RL1 06H ~RL 108 H RECTRON