SE2

SURFACE MOUNT SUPER FAST RECTIFIER VOLTAGE RANGE 50 to 400 Volts CURRENT 1.0 Ampere SE1 THRU SE6 FEATURES * * * * * * * * * * * * High r eliability Low l eakage L ow forward voltage H igh current capability S uper fast switching speed H igh surge capability G ood for switching mode circuit SOD-123F MECHANICAL DATA Case: Molded plastic Epoxy: Device has UL flammability classification 94V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0. 016 g ram .114 (2.9) .106 (2.7) .035 (0.90) .028 (0.70) .077 (1.95) .069 (1.75) .008 (0.20) .053 (1.35) .047 (1.20) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .030 (0.75) .022 (0.55) .150 (3.8) .142 (3.6) Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 5 5 OC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 1) Typical Thermal Resistance (Note 1) Typical Junction Capacitance (Note 2) Operating Te mperature Ran g e Storage Temperature R an g e SYMBOL VRRM VRMS VDC IO I FSM RqJA RqJL CJ TJ T STG 15 150 -55 to + 150 SE1 SE2 SE3 SE4 SE5 SE6 UNITS Volts Volts Volts Amps Amps 0 0 50 35 50 100 70 100 150 105 150 1.0 15 130 30 200 140 200 300 210 300 400 280 400 C/W C/W pF 0 0 10 C C E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0A DC Maximum Average Reverse Current at Rated DC Blocking Voltage @T A = 2 5 o C @T A = 1 00 o C SYMBOL VF IR trr SE1 SE2 SE3 SE4 SE5 SE6 UNITS Volts mA mA nSec 2006-12 0.95 5 350 35 1.25 Maximum Reverse Recovery Time (Note 4) NOTES : 1 . 2. 3. 4. Thermal Resistance :Mounted on PCB. Measured at 1 MHz and applied reverse voltage of 4.0 volts. "Fully ROHS compliant","100% Sn plating (Pb-free)". Test Conditions: I F= 0.5A, I R= -1.0A, I RR= -0.25A. RATING AND CHARACTERISTICS CURVES ( SE1 THRU SE6 ) 50 W NONINDUCTIVE 10 W NONINDUCTIVE +0.5A trr (+) 25 Vdc (approx) (-) D.U.T (-) PULSE GENERATOR (NOTE 2) 0 -0.25A 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) NOTES: 1 Rise Time = 7ns max. Input Impedance = 1 megohm. 22pF. 2. Rise Time = 10ns max. Source Impedance = 50 ohms. -1.0A 1cm SET TIME BASE FOR 14/1 ns/cm FIG.1 TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 1.0 AVERAGE FORWARD CURRENT, (A) INSTANTANEOUS REVERSE CURRENT, (uA) 1000 TA = 100 OC 0.8 0.6 0.4 0.2 0 Single Phase Half Wave 60Hz Resistive or Inductive Load 100 T A = 7 5 OC 10 1.0 T A = 2 5 OC 0 25 50 75 100 125 150 175 0.1 0 20 40 60 80 100 120 140 AMBIENT TEMPERATURE, (OC) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) FIG.2 TYPICAL FORWARD CURRENT DERATING CURVE FIG.3 TYPICAL REVERSE CHARACTERISTICS RATING AND CHARACTERISTICS CURVES ( SE1 THRU SE6 ) INSTANTANEOUS FORWARD CURRENT, (A) PEAK FORWARD SURGE CURRENT, (A) 20 10 3.0 1.0 0.3 0.1 0.03 0.01 0 20 10 T J = 2 5 OC SE1~SE4 8.3ms Single Half Sine-Wave (JEDED Method) SE5~SE6 5 3 2 1 Pulse Width=300uS 1% Duty Cycle 0.5 1.0 1.5 2.0 2.5 3.0 3.5 1 5 10 50 100 INSTANTANEOUS FORWARD VOLTAGE, (V) NUMBER OF CYCLES AT 60Hz FIG.4 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 200 JUNCTION CAPACITANCE, (pF) FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 100 60 40 20 10 6 4 2 1 0.1 0.2 0.4 1.0 2 4 10 SE5~SE6 SE1~SE4 T J = 2 5 OC 20 40 100 REVERSE VOLTAGE, (V) FIG.6 TYPICAL JUNCTION CAPACITANCE Mounting Pad Layout 0.030 MIN. (0.75 MIN.) 0.035MIN. (0.90 MIN.) 0.165 (4.19) REF Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.