SF162S

GLASS PASSIVATED SUPER FAST RECTIFIER VOLTAGE RANGE 50 to 600 Volts CURRENT 16 Amperes FEATURES SF161S T HRU SF167S .049 (1.25 REF.) * Low switching noise * Low forward voltage drop * Low thermal resistance * High current capability * Super fast switching speed * High reliability * Good for switching mode circuit D2-PAK .189 (4.80) .173 (4.40) .053 (1.35) .049 (1.25) MECHANICAL DATA .624 (15.84) PIN1 PIN2 .576 (14.64) * Case: D2-PAK molded plastic * Epoxy: Device has UL flammability classification 94V-O * Lead: MIL-STD-202E method 208C guaranteed * Mounting position: Any * We ight: 1.35 g r am s .346 (8.8) .323 (8.2) .069 (1.75) .126 (3.20) .110 (2.80) .098 (2.50) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .036 (0.91) .028 (0.71) .202 (5.13) .198 (5.03) .412 (10.46) .388 (9.86) .020 (0.50) .012 (0.30) PIN 1 PIN 2 HEATSINK Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T C = 1 00 o C Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 4) Typical Junction Capacitance (Note 2) Operating and Storage Temperature Ran g e O SYMBOL VRRM VRMS VDC IO I FSM R q JA R q JC CJ T J, T STG SF161S 50 35 50 SF162S 100 70 100 SF163S 150 105 150 SF164S 200 140 200 16.0 300 16 1.2 400 -55 to + 150 SF165S 300 210 300 SF166S 400 280 400 SF167S 600 420 600 .083 (2.10) .055 (1.40) .047 (1.20) .053 (1.35) UNITS Volts Volts Volts Amps Amps 0 C/ W pF 0 C E LECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 16.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 2 5 o C @T A = 1 00 o C SYMBOL VF IR trr 35 SF161S SF162S 1.0 10 500 50 SF163S SF164S SF165S SF166S SF167S 1.70 UNITS Volts m Amps nSec 2007-3 1.35 Maximum Reverse Recovery Time (Note 1) NOTES : 1. Test Conditions: IF = 0.5A, IR = -1.0A, IRR = -0.25A 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. Suffix "R" for Reverse Polarity. 4. Typical Thermal Resistance : Heat-sink mounted. 5. "Fully ROHS complaint", "100% Sn plating (Pb-free)" RATING AND CHARACTERISTICS CURVES ( SF161S THRU SF167S ) INSTANTANEOUS FORWARD CURRENT, (A) AVERAGE FORWARD CURRENT, (A) 20 16 12 8 4 0 Single Phase Half Wave 60 Hz Inductive or Resistive Load 50 30 20 164 S~ 16 SF 161 4 2 1.0 0.6 0.8 1.0 1.2 SF 10 SF 16 7S 12 SF 5S ~S 14 S F1 66 S T A = 2 5 OC Pulse Width = 300mS 1% Duty Cycle 0 50 100 O 150 1.4 1.6 1.8 2.0 CASE TEMPERATURE, ( C) INSTANTANEOUS FORWARD VOLTAGE, (V) INSTANTANEOUS REVERSE CURRENT, (mA) 1000 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE CT, JUNCTION CAPACITANCE, (pF) 1000 FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 TA = 100 OC 10 T A = 2 5 OC 100 1.0 0.1 0 20 40 60 80 100 120 140 10 0.1 0.2 T J = 2 5 OC 0.4 1.0 2 4 10 20 40 100 PERCENT RATED PEAK REVERSE VOLTAGE, (%) REVERSE VOLTAGE, (V) FIG.3 TYPICAL REVERSE CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) FIG.4 TYPICAL JUNCTION CAPACITANCE 300 250 200 150 100 50 0 1 2 5 8.3mS Single Half Sine-Wave JEDEC Method 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.