SMB2300C

SMB2300C SIDACTOR FEATURES * * * * * * Low switching noise L ow forward voltage drop H igh current capability High s witching capability H igh surge capabitity High r eliability DO-214AA MECHANICAL DATA * * * * * * Case: Molded plastic Epoxy: Device has UL flammability classification 9 4V-O Lead: MIL-STD-202E method 208C guaranteed Metallurgically bonded construction Mounting position: Any Weight: 0.098 gram 0.083 (2.11) 0.077 (1.96) 0.155 (3.94) 0.130 (3.30) 0.180 (4.57) 0.160 (4.06) 0.012 (0.305) 0.006 (0.152) 0.096 (2.44) 0.084 (2.13) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 0.060 (1.52) 0.030 (0.76) 0.008 (0.203) 0.004 (0.102) 0.220 (5.59) 0.205 (5.21) Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Peak One-Cycle Surge Current (Note 1) Off-state Capacitance (Note 2) O SYMBOL I TSM CO SMB2300C UNITS Amps pF 100 38 E LECTRICAL CHARACTERISTICS (@TA=25 C unless otherwise noted) CHARACTERISTICS Minimum On-state Voltage at 1.0A Peak Off-state Voltage @V DRM = 190V Switching Voltage @I S = 800mA (Note 3) Holding Current NOTES : 1. 2. 3. 4. SYMBOL VT IDRM VS IH SMB2300C UNITS Volts uA V mA 2006-12 4 5 260 150 Surge rating test standard : 10/100uS. Off-state capacitance is measured at 10KHz @0.3V with a DC48V bias. Vs is measured at 100V/uS. “Fully ROHS compliant”, “100% Sn plating (Pb-free)”. RATING AND CHARACTERISTICS CURVES ( SMB2300C ) +I IPP, PEAK PULSE CURRENT, (% IPP) IT IS IH -V IDRM VT VDRM VS +V 100 50 -I 0 tr td t, TIME, (uS) FIG.1 V-I CHARACTERISTICS 12 10 8 6 4 2 0 -2 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 CJ, JUNCTION CAPACITANCE, (pF) 14 PERCENT OF VS CHANGE, (%) FIG.2 PULSE WAVE-FORM 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 25 OC 25 OC TJ, JUNCTION TEMPERATURE, (OC) REVERSE VOLTAGE, (V) FIG.3 NORMALIZED VS CHANGE vs. JUNCTION TEMPERATURE FIG.4 NORMALIZED DC HOLDING CURRENT vs. CASE TEMPERATURE Mounting Pad Layout 0.106 MAX. (2.69 MAX.) 0.083MIN. (2.10 MIN.) 0.050 MIN. (1.27 MIN.) 0.220 (5.58) REF Dimensions in inches and (millimeters) DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.