SR0220

LOW Vf SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 to 200 Volts CURRENT 0.2 Ampere FEATURES * * * * * * SR0220 THRU SR02200 Low switching noise L ow forward voltage drop H igh current capability High s witching capability H igh surge capabitity High r eliability DO-41 * * * * * MECHANICAL DATA Case: Molded plastic Epoxy: Device has UL flammability classification 9 4V-O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 0.33 g ram .034 (0.9) 1.0 (25.4) MIN. .028 (0.7) DIA. .205 (5.2) .166 (4.2) .107 (2.7) .080 (2.0) DIA. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. 1.0 (25.4) MIN. Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A=110 OC Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 1) Typical Junction Capacitance (Note 3) Operating Te mperature Ran g e Storage Temperature R an g e CHARACTERISTICS Maximum Instantaneous Forward Voltage at 0.2A DC Maximum Average Reverse Current at Rated DC Blocking Voltage @T A = 2 5 o C @T A = 1 00 o C SYMBOL SR0220 SR0230 SR0240 SR0250 SR0260 SR0280 SR02100 SR02150 SR02200 UNITS VRRM VRMS VDC IO I FSM RqJA RqJL CJ TJ T STG 20 14 20 30 21 30 40 28 40 50 35 50 60 42 60 0.2 60 50 15 110 150 -55 to + 150 80 56 80 100 70 100 150 105 150 200 140 200 Volts Volts Volts Amps Amps 0 C/W pF 0 0 C C E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) SYMBOL SR0220 SR0230 SR0240 SR0250 SR0260 SR0280 SR02100 SR02150 SR02200 UNITS VF IR .28 1.0 10 Volts mA mA 2006-11 NOTES : 1 . Thermal Resistance : At 9.5mm lead lengths, PCB mounted. 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. "Fully ROHS compliant", "100% Sn plating (Pb-free)". RATING AND CHARACTERISTICS CURVES ( SR0220 THRU SR02200 ) 0.25 0.20 0.15 0.10 0.05 0 Single Phase Half Wave 60Hz Inductive or Resistive Load 0.375" (9.5mm) Lead Length INSTANTANEOUS FORWARD CURRENT, (mA) AVERAGE FORWARD CURRENT, (A) 100 TA = 125 OC 10 T A = 7 5 OC 1.0 0.1 T A = 2 5 OC SR0220 ~SR0240 SR0250~SR0260 SR0280~SR02200 0.01 0 50 100 O 150 0 20 40 60 80 100 120 140 AMBIENT TEMPERATURE, ( C) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS REVERSE CURRENT, (A) CJ, JUNCTION CAPACITANCE, (pF) 50 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 400 200 100 80 60 40 20 10 FIG.2 TYPICAL REVERSE CHARACTERISTICS T J = 2 5 OC 10 1.0 T J = 2 5 OC Pulse width=300mS 1% Duty Cycle 0.1 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.1 0.4 1.0 4 10 40 80 100 INSTANTANEOUS FORWARD VOLTAGE, (V) REVERSE VOLTAGE, (V) FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) FIG.4 TYPICAL JUNCTION CAPACITANCE 60 50 40 30 20 10 0 1 2 5 8.3mS Single Half Sine-Wave JEDEC Method 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.