SR20100CS

SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 to 200 Volts CURRENT 20.0 Ampere FEATURES SR2020CS THRU SR20200CS .346 (8.8) .323 (8.2) PIN 1 PIN 2 PIN 3 .624 (15.84) .576 (14.64) * * * * * MECHANICAL DATA ref. .049 (1.25 ) * Low switching noise * Low forward voltage drop * Low thermal resistance * High current capability * High switching capability * High surge capabitity * High reliability C ase: To-220 molded plastic Epoxy: Device has U L flammability classification 9 4 V - O Lead: MIL-STD-202E method 208C guaranteed Mounting position: Any Weight: 2. 24 g rams D2-PAK .189 (4.80) .173 (4.40) .053 (1.35) .049 (1.25) .126 (3.20) .110 (2.80) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. .202 (5.13) .198 (5.03) .412 (10.46) .388 (9.86) .020 (0.50) .012 (0.30) PIN 1 PIN 3 PIN 2 HEATSINK Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at Derating C ase Te mperature Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 1) Typical Junction Capacitance (Note 3) Operating Te mperature Ran g e Storage Temperature R an g e SYMBOL VRRM VRMS VDC IO I FSM RqJC RqJA CJ TJ T STG 700 150 -55 to + 150 SR2020CS SR2030CS SR2035CS SR2040CS SR2045CS SR2050CS SR2060CS SR2080CS SR20100CS SR20150CS SR20200CS .098 (2.50) .083 (2.10) .055 (1.40) .047 (1.20) .036 (0.91) .028 (0.71) .069 (1.75) .053 (1.35) UNITS Volts Volts Volts Amps Amps 0 20 14 20 30 21 30 35 25 35 40 28 40 45 32 45 50 35 50 20 150 2.0 40 60 42 60 80 56 80 100 70 100 150 105 150 200 140 200 C/W pF 0 0 500 C C E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 10.0A DC Maximum Average Reverse Current at Rated DC Blocking Voltage @T A = 2 5 o C @T A = 1 00 o C SYMBOL VF IR SR2020CS SR2030CS SR2035CS SR2040CS SR2045CS SR2050CS SR2060CS SR2080CS SR20100CS SR20150CS SR20200CS UNITS Volts mA mA 2009-04 REV: O .65 .75 1.0 10 .85 NOTES : 1 . Thermal Resistance : Heat-sink mounted. 2. Suffix “A” = Common Anode. 3. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 4. "Fully ROHS compliant","100% Sn plating (Pb-free)". RATING AND CHARACTERISTICS CURVES ( SR2020CS THRU SR20200CS ) 24 20 16 12 8 4 0 Single Phase Half Wave 60Hz Inductive or Resistive Load SR SR INSTANTANEOUS FORWARD CURRENT, (mA) AVERAGE FORWARD CURRENT, (A) 100 O 10 TA = 125 C 205 0C SR S~ 1 TA = 25 C O 20 20 CS ~S T A = 7 5 OC 202 00C S 0.1 R2 04 0C S SR2020CS~SR2040CS SR2050CS~SR2060CS SR2080CS~SR20200CS 0 50 100 O 150 0.01 0 20 40 60 80 100 120 140 LEAD TEMPERATURE, ( C) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS REVERSE CURRENT, (A) CJ, JUNCTION CAPACITANCE, (nF) 50 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE SR2020CS~SR2040CS 4 2 1 0.8 0.6 0.4 0.2 0.1 0.1 FIG.2 TYPICAL REVERSE CHARACTERISTICS T J = 2 5 OC 10 SR2080SC~SR20200CS SR 20 1.0 SR2050CS~SR2060CS SR 20 20 CS 50 C ~S S~ R2 SR 04 0.1 TJ = 25 C Pulse width=300mS 1% Duty Cycle O 20 5C S 20 0C S 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.4 1.0 4 10 40 80 100 INSTANTANEOUS FORWARD VOLTAGE, (V) REVERSE VOLTAGE, (V) FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) FIG.4 TYPICAL JUNCTION CAPACITANCE 150 125 100 75 50 25 0 1 8.3mS Single Half Sine-Wave JEDEC Method 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.