SR550K

SCHOTTKY BARRIER RECTIFIER VOLTAGE RANGE 20 to 200 Volts CURRENT 5.0 Ampere FEATURES * * * * * High reliability L ow switching loss Low forward voltage drop High current capability High switching capability SR520K THRU SR5200K .051 (1.3) .035 (0.9) MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O * Case: Molded plastic * Lead: MIL-STD-202E method 208C guaranteed * Mounting: position: Any * Weight: 0.33 grams D-PAK .264 (6.7) .248 (6.3) .217 (5.5) .201 (5.1) .098 (2.5) .083 (2.1) .024 (0.6) .016 (0.4) PIN3 .244 (6.2) .228 (5.8) .398 (10.11) .382 (9.71) PIN1 PIN2 MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. TYP .091 (2.30) .183 (4.65) .179 (4.55) .031 (0.8) .016 (0.4) PIN 1 PIN 2 PIN 3 TYP 1.00 TYP .020 (0.50) HEATSINK Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at Derating C ase Te mperature Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Typical Thermal Resistance (Note 1) Typical Junction Capacitance (Note 2) Operating Te mperature Ran g e Storage Temperature R an g e CHARACTERISTICS Maximum Instantaneous Forward Voltage at 5.0A DC Maximum Average Reverse Current at Rated DC Blocking Voltage @T A = 2 5 o C @T A = 1 00 o C SYMBOL SR520K SR530K SR540K SR550K SR560K SR580K SR5100K SR5150K SR5200K UNITS VRRM VRMS VDC IO I FSM RqJA RqJC CJ TJ T STG 20 14 20 30 21 30 40 28 40 50 35 50 60 42 60 5.0 150 60 3 200 150 -55 to + 150 80 56 80 100 70 100 150 105 150 200 140 200 Volts Volts Volts Amps Amps 0 C/W pF 0 0 C C E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) SYMBOL SR520K SR530K SR540K SR550K SR560K SR580K SR5100K SR5150K SR5200K UNITS VF IR .55 .75 0.2 2 .85 Volts mA mA 2006-12 NOTES : 1 . Thermal Resistance : Heat-sink case mounted or if PCB mounted. 2. Measured at 1 MHz and applied reverse voltage of 4.0 volts. 3. "Fully ROHS compliant", "100% Sn plating (Pb-free)". 4. Suffix "R" for Reverse Polarity. 5. Suffix "S" for D2-PAK Pkg. RATING AND CHARACTERISTICS CURVES ( SR520K THRU SR5200K ) INSTANTANEOUS REVERSE CURRENT, (mA) AVERAGE FORWARD CURRENT, (A) 6 5 SR SR 100 4 3 2 1 0 10 TA = 100 OC 55 0K ~S 580 Single Phase Half Wave 60Hz Inductive or Resistive Load 0.375" (9.5mm) Lead Length SR 52 0K SR K~ 520 R5 60 K ~S 1.0 T A = 2 5 OC SR520K ~SR540K SR550K~SR560K SR580K~SR5200K R5 40 K 0K 0.1 0 50 100 O 150 0.01 0 20 40 60 80 100 120 140 CASE TEMPERATURE, ( C) PERCENT OF RATED PEAK REVERSE VOLTAGE, (%) INSTANTANEOUS FORWARD CURRENT, (A) SR520K ~SR540K CJ, JUNCTION CAPACITANCE, (nF) 50 FIG.1 TYPICAL FORWARD CURRENT DERATING CURVE 400 200 100 80 60 40 20 10 FIG.2 TYPICAL REVERSE CHARACTERISTICS T J = 2 5 OC 10 SR550K~SR560K SR580K ~SR5200K 1.0 T J = 2 5 OC Pulse width=300mS 1% Duty Cycle 0.1 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 0.1 0.4 1.0 4 10 40 80 100 INSTANTANEOUS FORWARD VOLTAGE, (V) REVERSE VOLTAGE, (V) FIG.3 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PEAK FORWARD SURGE CURRENT, (A) FIG.4 TYPICAL JUNCTION CAPACITANCE 150 125 100 75 50 25 0 1 8.3mS Single Half Sine-Wave JEDEC Method 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz FIG.5 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.