T4ARBU406M

VOLTAGE RANGE 600 to 1000 Volts CURRENT 4.0 Amperes FEATURES * Ideal for printed circuit board * Surge overload rating: 130 amperes peak * Mounting position: Any TRANSIENT VOLTAGE SUPPRESSORS GPP BRIDGE RECTIFIER T4ARBU405M T HRU T4ARBU407M RBU MECHANICAL DATA * Epoxy: Device has UL flammability classification 94V-O .880 (22.3) .860 (21.8) .160 (4.1) .140 (3.5) .080 (2.03) .060 (1.52) .740 (18.8) .720 (18.3) .140 (3.56) .130 (3.30) .512 (13.0) .085 (2.16) .075 (1.90) .710 (18.0) .690 (17.5) .050 (1.27) .040 (1.02) .210 (5.33) .190 (4.83) .080 (2.03) .065 (1.65) .022 (0.56) .018 (0.46) .100 (2.54) .085 (2.16) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 o C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) MAXIMUM RAT INGS (@ TA=25 OC unless otherwise noted) R ATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current at T A = 5 0 o C (With Heat-sink) Peak Forward Surge Current 8.3 ms single half sine-wave superimposed on rated load (JEDEC method) Peak Power Dissipation at T A =25 OC,T P =1mS (Note 1) Breakdown Voltage Range at I T =1mA Maximum Peak Pulse Current Maximum Clamping Voltage at IPPM =0.73A Typical Junction Capacitance (Note 3) Operating and Storage Temperature Ran g e SYMBOL VRRM VRMS VDC IO I FSM PPPM VBR IPPM VC CJ T J, T STG T4ARBU405M 600 420 600 T4ARBU406M 800 560 800 4.0 130 Maximum 400 380~ 420 0.73 548 40 -55 to + 150 T4ARBU407M 1000 700 1000 UNITS Volts Volts Volts Amps Amps Watts Volts Amps Volts pF 0 C E LECTRICAL CHARACTERISTICS (@TA=25 OC unless otherwise noted) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 4.0A DC Maximum DC Reverse Current at Rated DC Blocking Voltage @T A = 25 o C @T A = 1 25 o C SYMBOL VF IR T4ARBU405M T4ARBU406M 1.1 5.0 500 T4ARBU407M UNITS Volts uAmps 2007-7 NOTES : 1 . Non-repetitive current pulse, per Fig.8 and derated above TA=25OC per Fig.7. 2. "Fully ROHS compliant", "100% Sn plating (Pb-free)". 3. Measured at 1MHz and applied reverse voltage of 4.0 voltage. RATING AND CHARACTERISTICS CURVES ( T4ARBU405M THRU T4ARBU407M ) AVERAGE FORWARD OUTPUT CURRENT, (A) INSTANTANEOUS FORWARD CURRENT, (A) 4.0 Heatsink Mounting, TC 1.6x1.6x0.06" Thk (4.0x4.0x.15cm) AL.Plate 40 3.0 10 4.0 2.0 P.C.B. Mounted,TA 0.47x0.47" (12x12mm) Copper Pads 0.375" (9.5mm) Lead Length 60Hz Resistive or Inductive Load 1.0 0.4 T A = 2 5 OC Pulse Width = 300mS 1% Duty Cycle 1.0 0 0 50 100 TEMPERATURE, ( C) O 150 0.1 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 INSTANTANEOUS FORWARD VOLTAGE, (V) FIG.1 DERATING CURVE OUTPUT RECTIFIED CURRENT INSTANTANEOUS REVERSE CURRENT, (uA) PEAK FORWARD SURGE CURRENT, (A) FIG.2 TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 240 200 160 120 80 40 0 1 8.3mS Single Half Sine-Wave JEDEC Method 1000 100 TA = 100 OC 10 T A = 2 5 OC 1.0 50~400V 600~1000V 0.1 0 20 40 60 80 100 120 140 2 5 10 20 50 100 PERCENT RATED PEAK REVERSE VOLTAGE, (%) NUMBER OF CYCLES AT 60Hz FIG.3 TYPICAL REVERSE CHARACTERISTICS TRANSIENT THERMAL IMPEDANCE, (OC/W) 1000 JUNCTION CAPACITANCE, (pF) 100 FIG.4 MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 10 100 1 10 0.1 1 10 100 0.1 0.01 0.1 1 t, HEATING TIME (sec.) 10 100 REVERSE VOLTAGE, (V) FIG.5 TYPICAL JUNCTION CAPACITANCE PER LEG FIG.6 TYPICAL TRANSIENT THERMA IMPEDANCE RATING AND CHARACTERISTICS CURVES ( T4ARBU405M THRU T4ARBU407M ) 100 PEAK PULSE POWER OR CURRETN DERATING IN PERCENTAGE, (%) 100 Non-Repetitive Pulse Waveform Shown in Fig.3 TA=25OC PEAK PULSE POWER, (KW) 75 10 50 1.0 25 0.1 0.1u 1.0u 10u 100u 1m 10u 0 0 25 50 75 100 125 150 175 200 PULSE WIDTH,(S) AMBIENT TEMPERATURE, (OC) FIG.7 PEAK PULSE POWER RATING CURVE 150 tr = 10usec. FIG.8 PULSE DERATING CURVE 100000 f = 1MHz Vsig = 50mVp-p TJ= 25 OC Pulse Width (td) is Defined as the Point Where the Peak Current Decays to 50% of I PPM Peak Value IPPM PEAK PULSE CURRENT, (%) 100 CJ, CAPACITANCE, (pF) 10000 HALF VALUE - IPPM Measured at Zero Bias 2 10/1000usec. Waveform as Defined by R.E.A. 50 1000 Measured at Stand off Voltage,VWM td 0 0 1.0 2.0 TIME, (mS) 3.0 4.0 100 1.0 10 V(BR), BREAKDOWN VOLTAGE, (V) 100 200 FIG.9 PULSE WAVEFORM FIG.10 TYPICAL JUNCTION CAPACITANCE Schematic DISCLAIMER NOTICE Rectron Inc reserves the right to make changes without notice to any product specification herein, to make corrections, modifications, enhancements or other changes. Rectron Inc or anyone on its behalf assumes no responsibility or liability for any errors or inaccuracies. Data sheet specifications and its information contained are intended to provide a product description only. "Typical" parameters which may be included on RECTRON data sheets and/ or specifications can and do vary in different applications and actual performance may vary over time. Rectron Inc does not assume any liability arising out of the application or use of any product or circuit. Rectron products are not designed, intended or authorized for use in medical, life-saving implant or other applications intended for life-sustaining or other related applications where a failure or malfunction of component or circuitry may directly or indirectly cause injury or threaten a life without expressed written approval of Rectron Inc. Customers using or selling Rectron components for use in such applications do so at their own risk and shall agree to fully indemnify Rectron Inc and its subsidiaries harmless against all claims, damages and expenditures.