4MA100000Z4BACUGI

4MA100000Z4 100.00 MHz LVDS Oscillator High Performance Differential MEMS Oscillator Features        Frequency: Output Type: Frequency Stability: Supply Voltage: Standard Packages: RMS phase jitter: Operating Temperature: 100.00 MHz LVDS ± 50ppm 2.5V & 3.3V 5.0 x 3.2 mm; 7.0 x 5.0 mm 0.7 ps typical (12k to 20MHz) - 40 to 85 °C Specification 2.5 V Specifications Parameter Min 2.375 Supply Voltage (VDD) Output Frequency 3.3 V Specifications Min 2.97 Typ Max 3.30 3.63 100.00 + 50 - 50 + 50 100 Supply Current Enable/Disable Time Input LOW level Input HIGH level Output LOW level Output HIGH level Amplitude (VA ) Mid Level (VM) Rise Time (TR) 105 1 0.3VDD 0. 7VDD 48 1 0.3VDD 0. 7VDD 1.05 1.40 0.35 1.22 400 Fall Time (TF) Symmetry (SYM) Phase Jitter Period Jitter Cycle-to-Cycle Jitter Start-up Time Aging 400 50 0.8 3.9 30 10 ±5 1.05 1.40 0.35 1.22 460 500 500 52 48 Block Diagram VDD 7.0 x 5.0 mm package shown (also available in 5.0 x 3.2mm pkg) Typ Max 2.50 2.625 100.00 - 50 Frequency Stability 460 50 0.7 3.9 30 10 ±5 DATASHEET 550 550 52 Units Conditions V MHz ppm mA us V V V V V V ps Includes supply voltage and temperature variation (-40 to 85°C), reflow drift, and aging. No load Guaranteed by design At OE pin At OE pin Single Ended output swing (Pk-Pk) Maximum; 20/80% of VA; Output load (CL) = 2pF; Guaranteed by Char. ps % ps ps ps ms ppm Maximum; 20/80% of VA; Output load (CL) = 2pF; Guaranteed by Char. Worst case; measured at 50% of waveform 12k to 20MHz, RMS; Measured Differentially RMS 1,000 cycles, Peak Output valid time after power up, 25°C 25°C, 10 years Output Waveform OUT- TR OUT+ TF MEMS IDT MEMS ASIC Output 80% VA VM 20% SYM = t1 / t2 OE NC 7.0 x 5.0 mm 5.0 x 3.2 mm Voltage 3.3 V 2.5 V 3.3 V 2.5 V t2 GND Part Ordering Information Package Size t1 Ordering Code 4MA100000Z4AACUGI 4MA100000Z4BACUGI 4MA100000Z4AACTGI 4MA100000Z4BACTGI 4MA 100000 Z4 A A CUG I 8 Frequency Voltage Package Temperature Shipping 100.000 MHz A: 3.3 V B: 2.5 V CTG: 5.0 x 3.2 CUG: 7.0 x 5.0 I: -40 to 85°C Blank: Tubes 8: T/R * Factory minimum order quantity: 500pcs (T/R) Jan 11, 2013 ©2013 Integrated Device Technology, Inc 4MA100000Z4 Datasheet 100.00 MHz LVDS MEMS Oscillator Pin Description Solder Reflow Profile 40 sec (max) (260°C max) 217°C 200 150 150°C ax Output Enable* No Connect Ground Output Complementary Output Power Supply Voltage 100 * Pulled high internally cm OE NC GND OUT+ OUT– VDD 3° C/ se 1 2 3 4 5 6 245°C 250 Temperature (°C) Description 60-150 sec 60-180 sec ma x Name /sec 6°C Pin # 50 Time Package Outline and Dimensions 3.20 ±0.05 Typical PCB Land Pattern 1.00 ±0.05 1.2 ±0.05 0.64 ±0.05 Pin #1 ID Chamfer 0.25 x 45° 1.30 ±0.05 5.0 ±0.05 1.50 ±0.05 GND 0.203 Ref. 2.4 0.85 ±0.05 0.0-0.05 Pin #1 ID Chamfer 0.30 x 45° 2.54 Bsc 0.90 1.50 3.60 OE VDD GND 1.00 Ref 0.203 Ref. 6024 Silver Creek Valley Road San Jose, California 95138 OUT+ NC 7.00 ±0.05 Sales Technical Support 800-345-7015 (inside USA) +1 408-284-8200 (outside USA) MEMS_Support@idt.com www.idt.com/go/MEMS OUT- 5.08 6L SMD NC 0.30 Ref 1.27 Bsc VDD OE 5.00 ±0.05 0.91 7.0 x 5.0mm 0.0-0.05 2.54 6L SMD 5.0 x 3.2mm 2.60 0.85 ±0.05 1.60 OUTOUT+ 1.60 Unit: (mm) DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright 2010, 2011, 2012, 2013. All rights reserved. Jan 11, 2013 www.IDT.com ©2013 Integrated Device Technology, Inc