4MA161133Z3AACTGI

161.133 MHz LVPECL Oscillator 4MA161133Z3 High Performance Differential Oscillator Features        Frequency: Output Type: Frequency Stability: Supply Voltage: Standard Packages: RMS phase jitter: Operating Temperature: Specification 161.133 MHz LVPECL ± 50ppm 2.5V & 3.3V 5.0 x 3.2 mm; 7.0 x 5.0 mm 0.7ps typical (12k to 20MHz) - 40 to 85 °C 2.5 V Specifications Parameter Min Supply Voltage (VDD) Output Frequency Frequency Stability Supply Current Input LOW level Input HIGH level Output LOW level Output HIGH level Rise Time (TR) Typ Max 3.3 V Specifications Min 2.50 161.133 Typ 3.30 161.133 ± 50 100 0.3VDD 0. 7VDD 0. 7VDD VDD -1.6 VDD -1.0 VDD -1.0 300 Max 300 0.75 VDD -1.3 0.75 VDD -1.3 45 55 3 1.0 ±5 This product is rated “Green”, please contact IDT for environmental compliancy information Units Conditions V MHz ± 50 ppm 100 mA 0.3VDD V V VDD -1.6 V V 300 ps 300 Fall Time (TF) Amplitude (VA ) Mid Level (VM) Symmetry (SYM) Period Jitter Phase Jitter Aging ADVANCE DATASHEET 45 55 3 1.0 ±5 -40 to 85°C no load At OE pin At OE pin Maximum; 20/80% of VA; Output load (CL) = 2pF ps V V % ps ps ppm Maximum; 20/80% of VA; Output load (CL) = 2pF Single Ended output swing (Pk-Pk) Worst case; measured at 50% of waveform Measured over 10k cycles, rms 12k to 20MHz, rms 25°C, 10 years Note: Above specifications are typical at room temperature (25°C ) unless otherwise specified. Frequency stability includes initial frequency tolerance, temperature variation, supply voltage variation, reflow drift, and aging (+25 °C, 10 years). Block Diagram VDD Output Waveform OUT- TR OUT+ TF 80% OE NC 20% GND Part Ordering Information Package Size 5.0 x 3.2 mm 7.0 x 5.0 mm May 09, 2012 Voltage 3.3 V 2.5 V 3.3 V 2.5 V VA VM Output MEMS IDT MEMS ASIC Ordering Code 4MA161133Z3AACTGI 4MA161133Z3BACTGI 4MA161133Z3AACUGI 4MA161133Z3BACUGI t1 SYM = t1 / t2 4MA 161133 Frequency 161.133 MHz t2 Z3 Voltage A: 3.3 V B: 2.5 V A A Package CTG: 5.0 x 3.2 CUG: 7.0 x 5.0 CTG Temperature I: -40 to 85°C I 8 Shipping Blank: Tubes 8: T/R ©2012 Integrated Device Technology, Inc Datasheet 161.133 MHz LVPECL Oscillator Package Outline and Dimensions 3.20 ±0.05 1.00 ±0.05 0.64 ±0.05 Pin #1 ID Chamfer 0.30 x 45° 0.0-0.05 NC 5.00 ±0.05 1.27 Bsc GND 1.30 ±0.05 Pin #1 ID R 0.15° OUT+ 1.50 3.60 0.85 ±0.05 0.0-0.05 OE VDD 5.08 6L SMD NC 7.00 ±0.05 2.54 Bsc 0.25 Ref GND 1.60 0.203 Ref. 6024 Silver Creek Valley Road San Jose, California 95138 OUT- 0.90 0.203 Ref. 1.50 ±0.05 7.0 x 5.0mm VDD OE 1.08 ±0.05 5.0 ±0.05 2.60 0.85 ±0.05 2.54 6L SMD 5.0 x 3.2mm Typical PCB Land Pattern OUTOUT+ Pin Name 1 OE 2 NC 3 GND 4 OUT+ 5 OUT6 VDD Description Output Enable* No Connect Ground Output Output Power * internally pulled high 1.60 Unit: (mm) Sales Technical Support +1 408-284-8200 Fax: 408-360-1738 MEMS_Support@idt.com www.idt.com/go/MEMS DISCLAIMER Integrated Device Technology, Inc. (IDT) and its subsidiaries reserve the right to modify the products and/or specifications described herein at any time and at IDT’s sole discretion. All information in this document, including descriptions of product features and performance, is subject to change without notice. Performance specifications and the operating parameters of the described products are determined in the independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT’s products for any particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties. IDT’s products are not intended for use in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT. Integrated Device Technology, IDT and the IDT logo are registered trademarks of IDT. Other trademarks and service marks used herein, including protected names, logos and designs, are the property of IDT or their respective third party owners. Copyright 2010, 2011, 2012. All rights reserved. May 09, 2012 www.IDT.com ©2012 Integrated Device Technology, Inc