571MLFT

DATASHEET ICS571 LOW PHASE NOISE ZERO DELAY BUFFER Description Features The ICS571 is a high speed, high output drive, low phase noise Zero Delay Buffer (ZDB) which integrates IDT’s proprietary analog/digital Phase Locked Loop (PLL) techniques. IDT introduced the world standard for these devices in 1992 with the debut of the AV9170, and updated that with the ICS570. The ICS571, part of IDT’s ClockBlocks™ family, was designed to operate at higher frequencies, with faster rise and fall times, and with lower phase noise. The zero delay feature means that the rising edge of the input clock aligns with the rising edges of both outputs, giving the appearance of no delay through the device. There are two outputs on the chip, one being a low-skew divide by two of the other. • • • • • Packaged in 8-pin SOIC (Pb free) • • • • Can recover poor input clock duty cycle The chip is ideal for synchronizing outputs in a large variety of systems, from personal computers to data communications to video. By allowing offchip feedback paths, the ICS571 can eliminate the delay through other devices. The use of dividers in the feedback path will enable the part to multiply by more than two. • Advanced, low power CMOS process • Operating voltages of 3.0 to 5.5 V Can function as low phase noise x2 multiplier Low skew outputs. One is ÷2 of other Input clock frequency up to 160 MHz at 3.3 V Phase noise of better than -100 dBc/Hz from 1 kHz to 1 MHz offset from carrier Output clock duty cycle of 45/55 at 3.3 V High drive strength for >100 MHz outputs Full CMOS clock swings with 25 mA drive capability at TTL levels Block Diagram IDT™ / ICS™ LOW PHASE NOISE ZERO DELAY BUFFER 1 ICS571 REV H 051310 ICS571 LOW PHASE NOISE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER Pin Assignment Feedback Configuration Table and Frequency Ranges (at 3.3 V) Feedback From CLK CLK/2 Input Range CLK Input clock frequency Input clock frequency/2 20 to 160 MHz CLK/2 2x Input clock frequency Input clock frequency 10 to 80 MHz Pin Descriptions Pin Number Pin Name Pin Type Pin Description 1 ICLK CI Reference clock input. 2 VDD P Connect to +3.3 V or +5 V. Must be same as other VDD. 3 GND P Connect to ground. 4 CLK/2 O Clock output per table above. Low skew divide by two of pin 7 clock. 5 GND P Connect to ground. 6 VDD P Connect to +3.3 V or +5 V. Must be same as other VDD. 7 CLK O Clock output per table above. 8 FBIN CI Feedback clock input. Connect to CLK or CLK/2 per table above. Key: CI = clock input; I = input; O = output; P = power supply connection. IDT™ / ICS™ LOW PHASE NOISE ZERO DELAY BUFFER 2 ICS571 REV H 051310 ICS571 LOW PHASE NOISE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER External Components pins 2 and 3, and between pins 6 and 5). They must be connected close to the ICS571 to minimize lead inductance. No external power supply filtering is required for this device. A 33Ω terminating resistor can be used next to each output pin. The ICS571 requires a minimum number of external components for proper operation. A decoupling capacitor of 0.01µF must be connected between VDD and GND on each side of the chip (between Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the ICS571. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Item Rating Supply Voltage, VDD, referenced to GND 7V Inputs, referenced to GND -0.5 V to VDD+0.5 V Clock Output, referenced to GND -0.5 V to VDD+0.5 V Storage Temperature -65 to +150° C Soldering Temperature, max of 10 seconds 260° C Ambient Operating Temperature 0 to +70° C IDT™ / ICS™ LOW PHASE NOISE ZERO DELAY BUFFER 3 ICS571 REV H 051310 ICS571 LOW PHASE NOISE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER DC Electrical Characteristics Unless stated otherwise, VDD = 5.0 V or 3.3 V, Ambient Temperature 0 to +70° C Parameter Symbol Operating Supply Voltage VDD Conditions Min. Typ. 3 Max. Units 5.5 V Input High Voltage VIH ICLK, FBIN (pins 1 and 8) Input Low Voltage VIL ICLK, FBIN (pins 1 and 8) Output High Voltage, CMOS level VOH IOH = -4 mA VDD-0.4 V Output High Voltage VOH IOH = -25 mA 2.4 V Output Low Voltage VOL IOL = 25 mA VDD/2+1 VDD/2 VDD/2 V VDD/2-1 0.4 V V IDD Operating Supply Current, 133 in, 133 out No load, 3.3 V 34 mA IDD Operating Supply Current, 50 in, 100 out No load, 3.3 V 26 mA Short Circuit Current IOS Each output ±100 mA Input Capacitance CIN ICLK, FBIN 5 pF IDT™ / ICS™ LOW PHASE NOISE ZERO DELAY BUFFER 4 ICS571 REV H 051310 ICS571 LOW PHASE NOISE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER AC Electrical Characteristics Unless stated otherwise, VDD = 5.0 V or 3.3 V, Ambient Temperature 0 to +70° C Parameter Symbol Conditions Min. Typ. Max. Units Input Frequency, clock input fIN FB from CLK 20 160 MHz Input Frequency, clock input fIN FB from CLK/2 10 80 MHz Skew CLK/2 with respect to CLK Note 2 150 850 ps Input clock to output connected to FBIN Note 2 -500 500 ps Output Clock Rise Time, 5 V 0.8 to 2.0 V, 15 pF load 0.3 ns Output Clock Fall Time, 5 V 2.0 to 0.8 V, 15 pF load 0.4 ns Output Clock Rise Time, 3.3 V 0.8 to 2.0 V, 15 pF load 0.45 ns Output Clock Fall Time, 3.3 V 2.0 to 0.8 V, 15 pF load 0.55 ns Input Clock Duty Cycle, 3.3 V fin = 150 MHz 20 Output Clock Duty Cycle, 3.3 V At VDD/2 45 Absolute Clock Period Jitter, CLK, Note 3 Deviation from Mean One-Sigma Clock Period Jitter, CLK, Note 3 500 49 to 51 80 % 55 % ±80 ps 50 ps Phase Noise, Relative to carrier 1 kHz offset -105 dBc/Hz Phase Noise, Relative to carrier 100 kHz offset -115 dBc/Hz Notes: 1. Sresses beyond these can permanently damage the device. 2. Assumes clocks with the same rise time, measured from rising edges at VDD/2. Measured with 33Ω termination resistors and 15 pF loads. Applies to both 3.3 V and 5 V operation. 3. CLK/2 has lower jitter (both absolute and one sigma, in ps) than CLK. Thermal Characteristics Parameter Thermal Resistance Junction to Ambient Thermal Resistance Junction to Case IDT™ / ICS™ LOW PHASE NOISE ZERO DELAY BUFFER Symbol Conditions Min. Typ. Max. Units θJA Still air ° C/W θJA 1 m/s air flow ° C/W θJA 3 m/s air flow ° C/W θJC ° C/W 5 ICS571 REV H 051310 ICS571 LOW PHASE NOISE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER Package Outline and Package Dimensions (8-pin SOIC, 150 Mil. Body) Package dimensions are kept current with JEDEC Publication No. 95 Millimeters 8 Symbol E Min A A1 B C D E e H h L α H INDEX AREA 1 2 D A Inches Max Min 1.35 1.75 0.10 0.25 0.33 0.51 0.19 0.25 4.80 5.00 3.80 4.00 1.27 BASIC 5.80 6.20 0.25 0.50 0.40 1.27 0° 8° Max .0532 .0688 .0040 .0098 .013 .020 .0075 .0098 .1890 .1968 .1497 .1574 0.050 BASIC .2284 .2440 .010 .020 .016 .050 0° 8° h x 45 A1 C -Ce B SEATING PLANE L .10 (.004) C Ordering Information Part / Order Number Marking Shipping Packaging Package Temperature 571MLF 571MLFT 571MLF Tubes Tape and Reel 8-pin SOIC 8-pin SOIC 0 to +70° C 0 to +70° C "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use. No other circuits, patents, or licenses are implied. This product is intended for use in normal commercial applications. Any other applications such as those requiring extended temperature range, high reliability, or other extraordinary environmental requirements are not recommended without additional processing by IDT. IDT reserves the right to change any circuitry or specifications without notice. IDT does not authorize or warrant any IDT product for use in life support devices or critical medical instruments. IDT™ / ICS™ LOW PHASE NOISE ZERO DELAY BUFFER 6 ICS571 REV H 051310 ICS571 LOW PHASE NOISE ZERO DELAY BUFFER ZDB AND MULTIPLIER/DIVIDER Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales For Tech Support 800-345-7015 408-284-8200 Fax: 408-284-2775 www.idt.com/go/clockhelp Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2006 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. IDT and the IDT logo are trademarks of Integrated Device Technology, Inc. Accelerated Thinking is a service mark of Integrated Device Technology, Inc. All other brands, product names and marks are or may be trademarks or registered trademarks used to identify products or services of their respective owners. Printed in USA IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.