Programmable Clock Generator
5P49V5925
DATASHEET
Description
Features
The 5P49V5925 is a programmable clock generator intended
for high-performance consumer, networking, industrial,
computing, and data-communications applications.
Configurations may be stored in on-chip One-Time
Programmable (OTP) memory or changed using I2C
interface. This is IDT’s fifth generation of programmable clock
technology (VersaClock® 5).
• Generates up to four independent output frequencies
• High-performance, low phase noise PLL, < 0.7 ps RMS
The frequencies are generated from a single reference clock.
The reference clock can come from one of the two redundant
clock inputs. A glitchless manual switchover function allows
one of the redundant clocks to be selected during normal
operation.
programmable or factory programmable OTP memory
typical phase jitter on outputs
• Four fractional output dividers (FODs)
• Independent Spread Spectrum capability on each output
• Four banks of internal non-volatile in-system
• I2C serial programming interface
• Five LVCMOS outputs, including one reference output
• I/O Standards:
– Single-ended I/Os: 1.8V to 3.3V LVCMOS
Two select pins allow up to 4 different configurations to be
programmed and accessible using processor GPIOs or
bootstrapping. The different selections may be used for
different operating modes (full function, partial function, partial
power-down), regional standards (US, Japan, Europe) or
system production margin testing.
• Input frequency ranges:
– LVCMOS Reference Clock Input (XIN/REF) – 1MHz to
200MHz
– LVDS, LVPECL, HCSL Differential Clock Input (CLKIN,
CLKINB) – 1MHz to 200MHz
– Crystal frequency range: 8MHz to 40MHz
The device may be configured to use one of two I2C
addresses to allow multiple devices to be used in a system.
• Output frequency ranges:
CLKIN
CLKINB
XOUT
1
24 23 22 21 20 19
18
VDDO2
2
17
OUT2
16
NC
XIN/REF
4
15
VDDO3
VDDA
5
14
OUT3
CLKSEL
6
3
EPAD
GND
– LVCMOS Clock Outputs – 1MHz to 200MHz
Individually selectable output voltage (1.8V, 2.5V, 3.3V) for
each output
Redundant clock inputs with manual switchover
Programmable loop bandwidth
Programmable slew rate control
Programmable crystal load capacitance
Individual output enable/disable
Power-down mode
1.8V, 2.5V or 3.3V core VDDD, VDDA
Available in 24-pin VFQFPN 4mm x 4mm package
-40° to +85°C industrial temperature operation
NC
NC
13
10 11 12
OUT4
9
VDDO4
8
SEL1/SDA
SEL0/SCL
SD/OE
7
•
•
•
•
•
•
•
•
•
NC
OUT1
VDDO1
VDDD
•
VDDO0
OUT0_SEL_I2CB
Pin Assignment
24-pin VFQFPN
5P49V5925 FEBRUARY 21, 2019
1
©2019 Integrated Device Technology, Inc.
5P49V5925 DATASHEET
Functional Block Diagram
VDDO0
XIN/REF
OUT0_SEL_I2CB
XOUT
VDDO1
FOD1
CLKIN
OUT1
VDDO2
CLKINB
FOD2
CLKSEL
PLL
OUT2
VDDO3
SD/OE
FOD3
OUT3
SEL1/SDA
VDDO4
SEL0/SCL
OTP
and
Control Logic
FOD4
OUT4
VDDA
VDDD
Applications
•
•
•
•
•
•
•
•
•
•
Ethernet switch/router
PCI Express 1.0/2.0/3.0
Broadcast video/audio timing
Multi-function printer
Processor and FPGA clocking
Any-frequency clock conversion
MSAN/DSLAM/PON
Fiber Channel, SAN
Telecom line cards
1 GbE and 10 GbE
PROGRAMMABLE CLOCK GENERATOR
2
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Table 1: Pin Descriptions
Number
Name
1
CLKIN
Input
Internal
Pull-down
Differential clock input. Weak 100kohms internal pull-down.
2
CLKINB
Input
Internal
Pull-down
Complementary differential clock input. Weak 100kohms internal pull-down.
3
XOUT
Input
Crystal Oscillator interface output.
4
XIN/REF
Input
Crystal Oscillator interface input, or single-ended LVCMOS clock input. Ensure that
the input voltage is 1.2V max. Refer to the section “Overdriving the XIN/REF
Interface”.
5
VDDA
Power
Analog functions power supply pin. Connect to 1.8V to 3.3V. VDDA and VDDD should
have the same voltage applied.
6
CLKSEL
Type
Input
Description
Internal
Pull-down
Input clock select. Selects the active input reference source in manual switchover
mode.
0 = XIN/REF, XOUT (default)
1 = CLKIN, CLKINB
CLKSEL Polarity can be changed by I2C programming as shown in Table 4.
7
SD/OE
Input
Internal
Pull-down
Enables/disables the outputs (OE) or powers down the chip (SD). The SH bit
controls the configuration of the SD/OE pin. The SH bit needs to be high for SD/OE
pin to be configured as SD. The SP bit (0x02) controls the polarity of the signal to be
either active HIGH or LOW only when pin is configured as OE (Default is active
LOW.) Weak internal pull down resistor. When configured as SD, device is shut
down and the single-ended LVCMOS outputs are driven low. When configured as
OE, and outputs are disabled, the outputs can be selected to be tri-stated or driven
high/low, depending on the programming bits as shown in the SD/OE Pin Function
Truth table.
8
SEL1/SDA
Input
Internal
Pull-down
Configuration select pin, or I2C SDA input as selected by OUT0_SEL_I2CB. Weak
internal pull down resistor.
9
SEL0/SCL
Input
Internal
Pull-down
Configuration select pin, or I2C SCL input as selected by OUT0_SEL_I2CB. Weak
internal pull down resistor.
10
VDDO4
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT4.
11
OUT4
Output
Output Clock 4. Please refer to the Output Drivers section for more details.
12
NC
–
No connect.
No connect.
13
NC
–
14
OUT3
Output
Output Clock 3. Please refer to the Output Drivers section for more details.
15
VDDO3
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT3.
16
NC
–
17
OUT2
Output
Output Clock 2. Please refer to the Output Drivers section for more details.
18
VDDO2
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT2.
19
NC
–
20
OUT1
Output
21
VDDO1
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT1.
Power
Digital functions power supply pin. Connect to 1.8 to 3.3V. VDDA and VDDD should
have the same voltage applied.
22
FEBRUARY 21, 2019
VDDD
No connect.
No connect.
Output Clock 1. Please refer to the Output Drivers section for more details.
3
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Number
Name
23
VDDO0
Type
Description
Power
Power supply pin for OUT0_SEL_I2CB. Connect to 1.8 to 3.3V. Sets output voltage
levels for OUT0.
Latched input/LVCMOS Output. At power up, the voltage at the pin
OUT0_SEL_I2CB is latched by the part and used to select the state of pins 8 and 9.
If a weak pull up (10kohms) is placed on OUT0_SEL_I2CB, pins 8 and 9 will be
configured as hardware select pins, SEL1 and SEL0. If a weak pull down (10Kohms)
is placed on OUT0_SEL_I2CB or it is left floating, pins 8 and 9 will act as the SDA
and SCL pins of an I2C interface. After power up, the pin acts as a LVCMOS
reference output.
24
OUT0_SEL_I2CB
Input/
Output
ePAD
GND
GND
PROGRAMMABLE CLOCK GENERATOR
Internal
Pull-down
Connect to ground pad.
4
FEBRUARY 21, 2019
5P49V5925 DATASHEET
PLL Features and Descriptions
If OUT0_SEL_I2CB was 0 at POR, alternate configurations
can only be loaded via the I2C interface.
Spread Spectrum
To help reduce electromagnetic interference (EMI), the
5P49V5925 supports spread spectrum modulation. The
output clock frequencies can be modulated to spread energy
across a broader range of frequencies, lowering system EMI.
The 5P49V5925 implements spread spectrum using the
Fractional-N output divide, to achieve controllable modulation
rate and spreading magnitude. The Spread spectrum can be
applied to any output clock, any clock frequency, and any
spread amount from ±0.25% to ±2.5% center spread and
-0.5% to -5% down spread.
Table 4: Input Clock Select
Input clock select. Selects the active input reference source in
manual switchover mode.
0 = XIN/REF, XOUT (default)
1 = CLKIN, CLKINB
CLKSEL Polarity can be changed by I2C programming as
shown in Table 4.
PRIMSRC
CLKSEL
Source
Table 2: Loop Filter
0
0
XIN/REF
PLL loop bandwidth range depends on the input reference
frequency (Fref) and can be set between the loop bandwidth
range as shown in the table below.
0
1
CLKIN, CLKINB
1
0
CLKIN, CLKINB
1
1
XIN/REF
Input Reference
Frequency–Fref
(MHz)
Loop
Bandwidth
Min (kHz)
Loop
Bandwidth
Max (kHz)
5
40
126
200
300
1000
PRIMSRC is bit 1 of Register 0x13.
Table 3: Configuration Table
This table shows the SEL1, SEL0 settings to select the
configuration stored in OTP. Four configurations can be stored
in OTP. These can be factory programmed or user
programmed.
OUT0_SEL_I2CB SEL1 SEL0
I 2C
REG0:7 Config
@ POR
Access
1
0
0
No
0
0
1
0
1
No
0
1
1
1
0
No
0
2
1
1
1
No
0
3
0
X
X
Yes
1
I2C
defaults
0
X
X
Yes
0
0
At power up time, the SEL0 and SEL1 pins must be tied to
either the VDDD/VDDA power supply so that they ramp with
that supply or are tied low (this is the same as floating the
pins). This will cause the register configuration to be loaded
that is selected according to Table 3 above. Providing that
OUT0_SEL_I2CB was 1 at POR and OTP register 0:7=0, after
the first 10mS of operation the levels of the SELx pins can be
changed, either to low or to the same level as VDDD/VDDA.
The SELx pins must be driven with a digital signal of < 300ns
Rise/Fall time and only a single pin can be changed at a time.
After a pin level change, the device must not be interrupted for
at least 1ms so that the new values have time to load and take
effect.
FEBRUARY 21, 2019
5
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Reference Clock Input Pins and
Selection
The capacitance at each crystal pin inside the chip starts at
9pF with setting 000000b and can be increased up to 25pF
with setting 111111b. The step per bit is 0.5pF.
The 5P49V5925 supports up to two clock inputs. One input
supports a crystal between XIN and XOUT. XIN can also be
driven from a single ended reference clock. XIN can accept
small amplitude signals like from TCXO or one channel of a
differential clock.
You can write the following equation for this capacitance:
Ci = 9pF + 0.5pF × XTAL[5:0]
The PCB where the IC and the crystal will be assembled adds
some stray capacitance to each crystal pin and more
capacitance can be added to each crystal pin with additional
external capacitors.
The second clock input (CLKIN, CLKINB) is a fully differential
input that only accepts a reference clock. The differential input
accepts differential clocks from all the differential logic types
and can also be driven from a single ended clock on one of the
input pins.
The CLKSEL pin selects the input clock between either
XTAL/REF or (CLKIN, CLKINB).
Either clock input can be set as the primary clock. The primary
clock designation is to establish which is the main reference
clock to the PLL. The non-primary clock is designated as the
secondary clock in case the primary clock goes absent and a
backup is needed. See the previous page for more details
about primary versus secondary clock operation.
The two external reference clocks can be manually selected
using the CLKSEL pin. The SM bits must be set to “0x” for
manual switchover which is detailed in Manual Switchover
Mode section.
You can write the following equations for the total capacitance
at each crystal pin:
Crystal Input (XIN/REF)
CXIN = Ci1 + Cs1 + Ce1
CXOUT = Ci2 + Cs2 + Ce2
The crystal used should be a fundamental mode quartz
crystal; overtone crystals should not be used.
Ci1 and Ci2 are the internal, tunable capacitors. Cs1 and Cs2
are stray capacitances at each crystal pin and typical values
are between 1pF and 3pF.
A crystal manufacturer will calibrate its crystals to the nominal
frequency with a certain load capacitance value. When the
oscillator load capacitance matches the crystal load
capacitance, the oscillation frequency will be accurate. When
the oscillator load capacitance is lower than the crystal load
capacitance, the oscillation frequency will be higher than
nominal and vice versa so for an accurate oscillation
frequency you need to make sure to match the oscillator load
capacitance with the crystal load capacitance.
Ce1 and Ce2 are additional external capacitors that can be
added to increase the crystal load capacitance beyond the
tuning range of the internal capacitors. However, increasing
the load capacitance reduces the oscillator gain so please
consult the factory when adding Ce1 and/or Ce2 to avoid
crystal startup issues. Ce1 and Ce2 can also be used to adjust
for unpredictable stray capacitance in the PCB.
To set the oscillator load capacitance there are two tuning
capacitors in the IC, one at XIN and one at XOUT. They can
be adjusted independently but commonly the same value is
used for both capacitors. The value of each capacitor is
composed of a fixed capacitance amount plus a variable
capacitance amount set with the XTAL[5:0] register.
Adjustment of the crystal tuning capacitors allows for
maximum flexibility to accommodate crystals from various
manufacturers. The range of tuning capacitor values available
are in accordance with the following table.
The final load capacitance of the crystal:
CL = CXIN × CXOUT / (CXIN + CXOUT)
For most cases it is recommended to set the value for
capacitors the same at each crystal pin:
CXIN = CXOUT = Cx → CL = Cx / 2
The complete formula when the capacitance at both crystal
pins is the same:
CL = (9pF + 0.5pF × XTAL[5:0] + Cs + Ce) / 2
XTAL[5:0] Tuning Capacitor Characteristics
Parameter
Bits
Step (pF)
Min (pF)
Max (pF)
XTAL
6
0.5
9
25
PROGRAMMABLE CLOCK GENERATOR
6
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Example 1: The crystal load capacitance is specified as 8pF
and the stray capacitance at each crystal pin is Cs=1.5pF.
Assuming equal capacitance value at XIN and XOUT, the
equation is as follows:
8pF = (9pF + 0.5pF × XTAL[5:0] + 1.5pF) / 2 →
0.5pF × XTAL[5:0] = 5.5pF → XTAL[5:0] = 11 (decimal)
Example 2: The crystal load capacitance is specified as 12pF
and the stray capacitance Cs is unknown. Footprints for
external capacitors Ce are added and a worst case Cs of 5pF
is used. For now we use Cs + Ce = 5pF and the right value for
Ce can be determined later to make 5pF together with Cs.
12pF = (9pF + 0.5pF × XTAL[5:0] + 5pF) / 2 →
XTAL[5:0] = 20 (decimal)
Manual Switchover Mode
When SM[1:0] is “0x”, the redundant inputs are in manual
switchover mode. In this mode, CLKSEL pin is used to switch
between the primary and secondary clock sources. The
primary and secondary clock source setting is determined by
the PRIMSRC bit. During the switchover, no glitches will occur
at the output of the device, although there may be frequency
and phase drift, depending on the exact phase and frequency
relationship between the primary and secondary clocks.
FEBRUARY 21, 2019
7
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Table 5: SD/OE Pin Function Truth Table
OTP Interface
The 5P49V5925 can also store its configuration in an internal
OTP. The contents of the device's internal programming
registers can be saved to the OTP by setting burn_start
(W114[3]) to high and can be loaded back to the internal
programming registers by setting usr_rd_start(W114[0]) to
high.
SH bit SP bit OSn bit OEn bit SD/OE
To initiate a save or restore using I2C, only two bytes are
transferred. The Device Address is issued with the read/write
bit set to “0”, followed by the appropriate command code. The
save or restore instruction executes after the STOP condition
is issued by the Master, during which time the 5P49V5925 will
not generate Acknowledge bits. The 5P49V5925 will
acknowledge the instructions after it has completed execution
of them. During that time, the I2C bus should be interpreted as
busy by all other users of the bus.
On power-up of the 5P49V5925, an automatic restore is
performed to load the OTP contents into the internal
programming registers. The 5P49V5925 will be ready to
accept a programming instruction once it acknowledges its
7-bit I2C address.
x
x
0
1
Tri-state2
Output active
Output active
Output driven High Low
0
0
0
0
1
1
1
1
0
1
1
1
x
0
1
1
x
x
0
1
Tri-state2
Output active
Output driven High Low
Output active
1
1
1
0
0
0
0
1
1
x
0
1
0
0
0
Tri-state2
Output active
Output active
1
1
1
1
1
1
1
x
0
1
1
x
x
0
1
x
0
0
0
1
Tri-state2
Output active
Output driven High Low
Output driven High Low 1
Besides the POR at power up, the same synchronization reset
is also triggered when switching between configurations with
the SEL0/1 pins. This ensures that the outputs remain aligned
in every configuration. This reset causes the outputs to
suspend for a few hundred microseconds so the switchover is
not glitch-less. The reset can be disabled for applications
where glitch-less switch over is required and alignment is not
critical.
When using I2C to reprogram an output divider during
operation, alignment can be lost. Alignment can be restored
by manually triggering the reset through I2C.
When alignment is required for outputs with different
frequencies, the outputs are actually aligned on the falling
edges of each output by default. Rising edge alignment can
also be achieved by utilizing the programmable skew feature
to delay the faster clock by 180 degrees. The programmable
skew feature also allows for fine tuning of the alignment.
OUTn
SD/OE Input
OSn
Global Shutdown
For details of register programming, please see VersaClock 5
Family Register Descriptions and Programming Guide for
details.
When configured as SD, device is shut down, and the
single-ended LVCMOS outputs are driven low. When
configured as OE, and outputs are disabled, the outputs are
driven high/low.
PROGRAMMABLE CLOCK GENERATOR
x
0
1
1
Each output divider block has a synchronizing POR pulse to
provide startup alignment between outputs. This allows
alignment of outputs for low skew performance. The phase
alignment works both for integer output divider values and for
fractional output divider values.
The polarity of the SD/OE signal pin can be programmed to be
either active HIGH or LOW with the SP bit (W16[1]). When SP
is “0” (default), the pin becomes active LOW and when SP is
“1”, the pin becomes active HIGH. The SD/OE pin can be
configured as either to shutdown the PLL or to enable/disable
the outputs. The SH bit controls the configuration of the
SD/OE pin The SH bit needs to be high for SD/OE pin to be
configured as SD.
SH
0
1
1
1
Output Alignment
SD/OE Pin Function
OEn
0
0
0
0
Note 1 : Global Shutdown
Note 2 : Tri-state regardless of OEn bits
Availability of Primary and Secondary I2C addresses to allow
programming for multiple devices in a system. The I2C slave
address can be changed from the default 0xD4 to 0xD0 by
programming the I2C_ADDR bit D0. VersaClock 5
Programming Guide provides detailed I2C programming
guidelines and register map.
SP
OUTn
0
0
0
0
8
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Output Divides
Device Hardware Configuration
Each of the four output divides are comprised of a 12-bit
integer counter, and a 24-bit fractional counter. The output
divide can operate in integer divide only mode for improved
performance, or utilize the fractional counters to generate any
frequency with a synthesis accuracy better than 50ppb.
The 5P49V5925 supports an internal One-Time
Programmable (OTP) memory that can be pre-programmed
at the factory with up to 4 complete device configuration.
These configurations can be over-written using the serial
interface once reset is complete. Any configuration written via
the programming interface needs to be re-written after any
power cycle or reset. Please contact IDT if a specific
factory-programmed configuration is desired.
The Output Divide also has the capability to apply a spread
modulation to the output frequency. Independent of output
frequency, a triangle wave modulation between 30 and 63kHz
may be generated.
Device Start-up & Reset Behavior
Output Skew
The 5P49V5925 has an internal power-up reset (POR) circuit.
The POR circuit will remain active for a maximum of 10ms
after device power-up.
For outputs that share a common output divide value, there
will be the ability to skew outputs by quadrature values to
minimize interaction on the PCB. The skew on each output
can be adjusted from 0 to 360 degrees. Skew is adjusted in
units equal to 1/32 of the VCO period. So, for 100 MHz output
and a 2800 MHz VCO, you can select how many 11.161pS
units you want added to your skew (resulting in units of 0.402
degrees). For example, 0, 0.402, 0.804, 1.206, 1.408, and so
on. The granularity of the skew adjustment is always
dependent on the VCO period and the output period.
Upon internal POR circuit expiring, the device will exit reset
and begin self-configuration.
The device will load internal registers using the configuration
stored in the internal One-Time Programmable (OTP)
memory.
Once the full configuration has been loaded, the device will
respond to accesses on the serial port and will attempt to lock
the PLL to the selected source and begin operation.
Output Drivers
Power Up Ramp Sequence
The operating voltage ranges of each output is determined by
its independent output power pin (VDDO) and thus each can
have different output voltage levels. Output voltage levels of
1.8V, 2.5V, or 3.3V are supported for LVCMOS.
VDDA and VDDD must ramp up together. VDDO0~4 must
ramp up before, or concurrently with, VDDA and VDDD. All
power supply pins must be connected to a power rail even if
the output is unused. All power supplies must ramp in a linear
fashion and ramp monotonically.
Each output may be enabled or disabled by register bits.
When disabled an output will be in a logic 0 state as
determined by the programming bit table shown on page 6.
VDDO0~4
LVCMOS Operation
Outputs OUT1, OUT2, OUT3, and OUT4 each operates the
frequency as determined by responding programmed
Fractional Output Dividers. All the previously described
configuration and control apply equally to all outputs.
Frequency, phase alignment, voltage levels and enable /
disable status apply to all the OUTx pins. The outputs can be
selected to be phase-aligned with each other or inverted
relative to one another by register programming bits. Selection
of phase-alignment may have negative effects on the phase
noise performance of any part of the device due to increased
simultaneous switching noise within the device.
FEBRUARY 21, 2019
VDDA
VDDD
9
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
I2C Mode Operation
The device acts as a slave device on the I2C bus using one of
the two I2C addresses (0xD0 or 0xD4) to allow multiple
devices to be used in the system. The interface accepts
byte-oriented block write and block read operations. Two
address bytes specify the register address of the byte position
of the first register to write or read. Data bytes (registers) are
accessed in sequential order from the lowest to the highest
byte (most significant bit first). Read and write block transfers
can be stopped after any complete byte transfer. During a
write operation, data will not be moved into the registers until
the STOP bit is received, at which point, all data received in
the block write will be written simultaneously.
For full electrical I2C compliance, it is recommended to use
external pull-up resistors for SDATA and SCLK. The internal
pull-down resistors have a size of 100k typical.
Current Read
S
Dev Addr + R
A
Data 0
A
Data 1
A
A
Data n
Abar
P
A
Data 1
Sequential Read
S
Dev Addr + W
A
Reg start Addr
A
A
Reg start Addr
A
Sr
Dev Addr + R
A
Data 0
Data 1
A
A
A
Data n
Abar
P
Sequential Write
S
Dev Addr + W
from master to slave
from slave to master
Data 0
A
A
Data n
A
P
S = start
Sr = repeated start
A = acknowledge
Abar= none acknowledge
P = stop
I2C Slave Read and Write Cycle Sequencing
PROGRAMMABLE CLOCK GENERATOR
10
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Table 6: I2C Bus DC Characteristics
Symbol
Parameter
Conditions
Min
VIH
Input HIGH Level
For SEL1/SDA pin and
SEL0/SCL pin
0.7xVDDD
VIL
Input LOW Level
For SEL1/SDA pin and
SEL0/SCL pin
GND-0.3
VHYS
IIN
VOL
Typ
Max
5.5
2
0.3xVDDD
0.05xVDDD
Hysteresis of Inputs
Output LOW Voltage
V
V
V
-1
Input Leakage Current
Unit
IOL = 3 mA
30
µA
0.4
V
Table 7: I2C Bus AC Characteristics
Symbol
FSCLK
Parameter
Min
Typ
Max
Unit
400
kHz
Serial Clock Frequency (SCL)
10
Bus free time between STOP and START
1.3
µs
tSU:START
Setup Time, START
0.6
µs
tHD:START
Hold Time, START
0.6
µs
0.1
µs
0
µs
tBUF
tSU:DATA
Setup Time, data input (SDA)
tHD:DATA
Hold Time, data input (SDA)
1
tOVD
Output data valid from clock
0.9
µs
CB
Capacitive Load for Each Bus Line
400
pF
tR
Rise Time, data and clock (SDA, SCL)
20 + 0.1xCB
300
ns
tF
Fall Time, data and clock (SDA, SCL)
20 + 0.1xCB
300
ns
tHIGH
HIGH Time, clock (SCL)
0.6
µs
tLOW
LOW Time, clock (SCL)
1.3
µs
Setup Time, STOP
0.6
µs
tSU:STOP
Note 1: A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIH(MIN) of the SCL signal) to bridge
the undefined region of the falling edge of SCL.
Note 2: I2C inputs are 5V tolerant.
FEBRUARY 21, 2019
11
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Table 8: Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the 5P49V5925. These ratings, which are standard values for IDT
commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in
the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect
product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range.
Item
Rating
Supply Voltage, VDDA, VDDD, VDDO
3.465V
Inputs
XIN/REF
CLKIN, CLKINB
Other inputs
0V to 1.2V voltage swing
0V to 1.2V voltage swing single-ended
-0.5V to VDDD
Outputs, VDDO (LVCMOS)
-0.5V to VDDO+ 0.5V
Outputs, IO (SDA)
10mA
Package Thermal Impedance, JA
42C/W (0 mps)
Package Thermal Impedance, JC
41.8C/W (0 mps)
Storage Temperature, TSTG
-65C to 150C
ESD Human Body Model
2000V
Junction Temperature
125°C
Table 9: Recommended Operation Conditions
Symbol
Parameter
Min
Typ
Max
Unit
VDDOX
Power supply voltage for supporting 1.8V outputs
1.71
1.8
1.89
V
VDDOX
Power supply voltage for supporting 2.5V outputs
2.375
2.5
2.625
V
VDDOX
Power supply voltage for supporting 3.3V outputs
3.135
3.3
3.465
V
VDDD
Power supply voltage for core logic functions
1.71
3.465
V
VDDA
Analog power supply voltage. Use filtered analog power
supply.
1.71
3.465
V
Operating temperature, ambient
-40
+85
°C
15
pF
MHz
TA
CLOAD_OUT Maximum load capacitance (3.3V LVCMOS only)
FIN
tPU
External reference crystal
1
40
External reference clock CLKIN, CLKINB
1
200
0.05
5
Power up time for all VDDs to reach minimum specified
voltage (power ramps must be monotonic)
ms
Note: VDDO1 and VDDO2 must be powered on either before or simultaneously with VDDD, VDDA and VDDO0.
PROGRAMMABLE CLOCK GENERATOR
12
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Table 10:Input Capacitance, LVCMOS Output Impedance, and Internal Pull-down
Resistance (TA = +25 °C)
Symbol
CIN
Parameter
Min
Typ
Max
Unit
3
7
pF
300
k
Input Capacitance (CLKIN, CLKINB, CLKSEL, SD/OE, SEL1/SDA,
SEL0/SCL)
Pull-down
Resistor
ROUT
100
CLKSEL, SD/OE, SEL1/SDA, SEL0/SCL, CLKIN, CLKINB,
OUT0_SEL_I2CB
XIN/REF
XOUT
17
LVCMOS Output Driver Impedance (VDDO = 1.8V, 2.5V, 3.3V)
Programmable input capacitance at XIN/REF
0
8
pF
Programmable input capacitance at XOUT
0
8
pF
Table 11:Crystal Characteristics
Parameter
Test Conditions
Min
Typ
Max
Units
25
40
MHz
10
100
7
pF
12
pF
8
pF
100
µW
Fundamental
Mode of Oscillation
8
Frequency
Equivalent Series Resistance (ESR)
Shunt Capacitance
Load Capacitance (CL) @ 25M to 40M
6
8
Maximum Crystal Drive Level
Note: Typical crystal used is FOX 603-25-150. For different reference crystal options please go to www.foxonline.com.
Table 12:DC Electrical Characteristics
Symbol
Parameter
Iddcore3 Core Supply Current
Iddox
Output Buffer Supply Current
Test Conditions
Typ
Max
Unit
100 MHz on all outputs,
25 MHz REFCLK
30
34
mA
LVCMOS, 50 MHz, 3.3V VDDOX, 1,2
16
18
mA
LVCMOS, 50 MHz, 2.5V VDDOX, 1,2
14
16
mA
1,2
12
14
mA
LVCMOS, 200 MHz, 3.3V VDDOX,
1,2
36
42
mA
LVCMOS, 200 MHz, 2.5V VDDOX,
1,2
27
32
mA
LVCMOS, 200 MHz, 1.8V VDDOX, 1,2
16
19
mA
10
14
mA
LVCMOS, 50 MHz, 1.8V VDDOX,
Iddpd
Core Power Down Current
Min
SD asserted,
I2C
Programming
1.Single CMOS driver active.
2.Measured into a 5” 50 Ohm trace with 2 pF load.
3. Iddcore = IddA + IddD, no loads.
FEBRUARY 21, 2019
13
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Table 13:Electrical Characteristics – Differential Clock Input Parameters 1,2 (Supply
Voltage VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, 1.8V ±5%, TA = -40°C to +85°C)
Symbol
Parameter
Test Conditions
Min
Typ
Max
Unit
VIH
Input HIGH Voltage–CLKIN, CLKINB
Single-ended input
0.55
1.7
V
VIL
Input LOW Voltage–CLKIN, CLKINB
Single-ended input
GND - 0.3
0.4
V
VSWING
Input Amplitude - CLKIN, CLKINB
Peak to Peak value, single-ended
200
1200
mV
dv/dt
Input Slew Rate - CLKIN, CLKINB
Measured differentially
0.4
8
V/ns
IIL
Input Leakage Low Current
VIN = GND
-5
5
µA
IIH
Input Leakage High Current
VIN = 1.7V
20
µA
Input Duty Cycle
Measurement from differential
waveform
55
%
dTIN
45
1. Guaranteed by design and characterization, not 100% tested in production.
2. Slew rate measured through ±75mV window centered around differential zero.
Table 14:DC Electrical Characteristics for 3.3V LVCMOS (VDDO = 3.3V±5%, TA = -40°C to +85°C) 1
Symbol
Parameter
Test Conditions
Min
2.4
Typ
Max
Unit
VDDO
V
0.4
V
VOH
Output HIGH Voltage
IOH = -15mA
VOL
Output LOW Voltage
IOL = 15mA
IOZDD
Output Leakage Current
(OUT1~4)
Tri-state outputs, VDDO = 3.465V
5
µA
IOZDD
Output Leakage Current
(OUT0)
Tri-state outputs, VDDO = 3.465V
30
µA
VIH
Input HIGH Voltage
Single-ended inputs - CLKSEL,
SD/OL
0.7xVDDD
VDDD + 0.3
V
VIL
Input LOW Voltage
Single-ended inputs, CLKSEL,
SD/O
GND - 0.3
0.3xVDDD
V
VIH
Input HIGH Voltage
Single-ended input
OUT0_SEL_I2CB
2
VDDO0 + 0.3
V
VIL
Input LOW Voltage
Single-ended input
OUT0_SEL_I2CB
GND - 0.3
0.4
V
VIH
Input HIGH Voltage
Single-ended input - XIN/REF
0.8
1.2
V
VIL
Input LOW Voltage
Single-ended input - XIN/REF
GND - 0.3
0.4
V
TR/TF
Input Rise/Fall Time
CLKSEL, SD/OE, SEL1/SDA,
SEL0SCL
300
ns
1. See “Recommended Operating Conditions” table.
PROGRAMMABLE CLOCK GENERATOR
14
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Table 15:DC Electrical Characteristics for 2.5V LVCMOS (VDDO = 2.5V±5%, TA = -40°C to +85°C)
Symbol
Parameter
Test Conditions
VOH
Output HIGH Voltage
IOH = -12mA
VOL
Output LOW Voltage
IOL = 12mA
IOZDD
Output Leakage Current
(OUT1~4)
IOZDD
Min
Typ
Max
0.7xVDDO
Unit
V
0.4
V
Tri-state outputs, VDDO = 3.465V
5
µA
Output Leakage Current
(OUT0)
Tri-state outputs, VDDO = 3.465V
30
µA
VIH
Input HIGH Voltage
Single-ended inputs - CLKSEL,
SD/OE
0.7xVDDD
VDDD + 0.3
V
VIL
Input LOW Voltage
Single-ended inputs, CLKSEL,
SD/OE
GND - 0.3
0.3xVDDD
V
VIH
Input HIGH Voltage
Single-ended input
OUT0_SEL_I2CB
1.7
VDDO0 + 0.3
V
VIL
Input LOW Voltage
Single-ended input
OUT0_SEL_I2CB
GND - 0.3
0.4
V
VIH
Input HIGH Voltage
Single-ended input - XIN/REF
0.8
1.2
V
VIL
Input LOW Voltage
Single-ended input - XIN/REF
GND - 0.3
0.4
V
TR/TF
Input Rise/Fall Time
CLKSEL, SD/OE, SEL1/SDA,
SEL0SCL
300
ns
Table 16:DC Electrical Characteristics for 1.8V LVCMOS (VDDO = 1.8V±5%, TA = -40°C to +85°C)
Symbol
Parameter
Test Conditions
Min
Max
Unit
VDDO
V
0.25 x VDDO
V
VOH
Output HIGH Voltage
IOH = -8mA
VOL
Output LOW Voltage
IOL = 8mA
IOZDD
Output Leakage Current
(OUT1~4)
Tri-state outputs, VDDO = 3.465V
5
µA
IOZDD
Output Leakage Current
(OUT0)
Tri-state outputs, VDDO = 3.465V
30
µA
VIH
Input HIGH Voltage
Single-ended inputs - CLKSEL,
SD/O
0.7 * VDDD
VDDD + 0.3
V
VIL
Input LOW Voltage
Single-ended inputs, CLKSEL,
SD/OL
GND - 0.3
0.3 * VDDD
V
VIH
Input HIGH Voltage
Single-ended input
OUT0_SEL_I2CB
0.65 * VDDO0
VDDO0 + 0.3
V
VIL
Input LOW Voltage
Single-ended input
OUT0_SEL_I2CB
GND - 0.3
0.4
V
VIH
Input HIGH Voltage
Single-ended input - XIN/REF
0.8
1.2
V
VIL
Input LOW Voltage
Single-ended input - XIN/REF
GND - 0.3
0.4
V
TR/TF
Input Rise/Fall Time
CLKSEL, SD/OE, SEL1/SDA,
SEL0SCL
300
ns
FEBRUARY 21, 2019
0.7 xVDDO
Typ
15
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Table 17:AC Timing Electrical Characteristics
(VDDO = 3.3V+5% or 2.5V+5% or 1.8V ±5%, TA = -40°C to +85°C)
(Spread Spectrum Generation = OFF)
Symbol
1
fIN
Parameter
Input Frequency
Test Conditions
Min.
Typ.
Max.
Units
Input frequency limit (XIN)
8
40
MHz
Input frequency limit (REF)
1
200
MHz
Input frequency limit (CLKIN, CLKINB)
1
200
MHz
1
200
MHz
fOUT
Output Frequency
Single ended clock output limit (LVCMOS)
fVCO
VCO Frequency
VCO operating frequency range
2600
2900
MHz
fPFD
PFD Frequency
PFD operating frequency range
11
150
MHz
fBW
Loop Bandwidth
Input frequency = 25MHz
0.06
0.9
MHz
t2
Input Duty Cycle
Duty Cycle
45
50
55
%
Output Duty Cycle
Measured at VDD/2, all outputs except
Reference output OUT0, VDDOX= 2.5V or 3.3V
45
50
55
%
Measured at VDD/2, all outputs except
Reference output OUT0, VDDOX=1.8V
40
50
60
%
Measured at VDD/2, Reference output
OUT0 (5MHz - 120MHz) with 50% duty cycle input
40
50
60
%
Measured at VDD/2, Reference output
OUT0 (150.1MHz - 200MHz) with 50% duty cycle
input
30
50
70
%
Single-ended 3.3V LVCMOS output clock rise and
fall time, 20% to 80% of VDDO
(Output Load = 5 pF) VDDOX=3.3V
1.0
2.2
V/ns
1.2
2.3
V/ns
Slew Rate, SLEW[1:0] = 10
1.3
2.4
V/ns
Slew Rate, SLEW[1:0] = 11
1.7
2.7
V/ns
0.6
0.3
V/ns
0.7
1.4
V/ns
Slew Rate, SLEW[1:0] = 10
0.6
1.4
V/ns
Slew Rate, SLEW[1:0] = 11
1.0
1.7
V/ns
0.3
0.7
V/ns
0.4
0.8
V/ns
Slew Rate, SLEW[1:0] = 10
0.4
0.9
V/ns
Slew Rate, SLEW[1:0] = 11
0.7
1.2
V/ns
t3
5
t4 2
Slew Rate, SLEW[1:0] = 00
Slew Rate, SLEW[1:0] = 01
Slew Rate, SLEW[1:0] = 00
Slew Rate, SLEW[1:0] = 01
Slew Rate, SLEW[1:0] = 00
Slew Rate, SLEW[1:0] = 01
PROGRAMMABLE CLOCK GENERATOR
Single-ended 2.5V LVCMOS output clock rise and
fall time, 20% to 80% of VDDO
(Output Load = 5 pF) VDDOX=2.5V
Single-ended 1.8V LVCMOS output clock rise and
fall time, 20% to 80% of VDDO
(Output Load = 5 pF) VDDOX=1.8V
16
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Symbol
t6
Parameter
Clock Jitter
Test Conditions
Min.
Typ.
Max.
Units
Cycle-to-Cycle jitter (Peak-to-Peak), multiple
output frequencies switching, LVCMOS outputs
(1.8 to 3.3V nominal output voltage)
OUT0=25MHz
OUT1=100MHz
OUT2=125MHz
OUT3=156.25MHz
74
ps
RMS Phase Jitter (12kHz to 5MHz integration
range) reference clock (OUT0),
25 MHz LVCMOS outputs (1.8 to 3.3V nominal
output voltage).
OUT0=25MHz
OUT1=100MHz
OUT2=125MHz
OUT3=156.25MHz
0.5
ps
RMS Phase Jitter (12kHz to 20MHz integration
range) LVCMOS output, VDDO = 3.465V, 25MHz
crystal, 156.25MHz output frequency
OUT0=25MHz
OUT1=100MHz
OUT2=125MHz
OUT3=156.25MHz
0.75
75
t7
Output Skew
Skew between the same frequencies, with outputs
using the same driver format and phase delay set
to 0ns.
t8 3
Startup Time
PLL lock time from power-up, measured after all
VDD's have raised above 90% of their target
value.
t9 4
Startup Time
PLL lock time from shutdown mode
1.5
3
ps
ps
10
ms
4
ms
1. Practical lower frequency is determined by loop filter settings.
2. A slew rate of 2.75V/ns or greater should be selected for output frequencies of 100MHz or higher.
3. Includes loading the configuration bits from memory to PLL registers. It does not include memory programming/write time.
4. Actual PLL lock time depends on the loop configuration.
5. Duty Cycle is only guaranteed at max slew rate settings.
Table 18:Spread Spectrum Generation Specifications
Symbol
Parameter
Description
fOUT
Output Frequency
Output Frequency Range
fMOD
Mod Frequency
Modulation Frequency
Spread Value
fSPREAD
FEBRUARY 21, 2019
Min
Typ
5
Max
Unit
300
MHz
30 to 63
kHz
Amount of Spread Value (programmable) - Center Spread
±0.25% to ±2.5%
%fOUT
Amount of Spread Value (programmable) - Down Spread
-0.5% to -5%
17
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Test Circuits and Loads
VDDOx
VDDD
VDDA
0.1µF
OUTx
0.1µF
0.1µF
CLKOUT
CL
GND
Test Circuits and Loads for Outputs
Typical Phase Noise at 100MHz (3.3V, 25°C)
NOTE: All outputs operational at 100MHz, Phase Noise Plot with Spurs On.
PROGRAMMABLE CLOCK GENERATOR
18
FEBRUARY 21, 2019
A
B
C
6.8 pF
NO-POP
C7
2
1
R7
10K
7
SD
C1
10uF
8
C10
.1uF
C4
.1uF
C9
.1uF
V1P8VC
2.2
C8
.1uF
R2
2
V1P8VC
OUTR0
V1P8VC
OUTR1
V1P8VC
OUTR2
V1P8VC
OUTR3
V1P8VC
OUTR4
23
24
21
20
19
18
17
16
15
14
13
10
11
12
OUT_0_SEL-I2C
PULL-UP FOR
HARDWARE
CONFIGURATION
CONTROL
REMOVE FOR I2C
V1P8VC
22
7
6
5
4
R9
10K
V1P8VC
R6 1
C2
1uF
V1P8VCA
4
C3
.1uF
V1P8VCA
The follow pins have
weak internal
pull-down resistors:
6,7,8,9 and 24
VDDO4
OUT4
NC
VDDO3
OUT3
NC
VDDO2
OUT2
NC
VDDO1
OUT1
NC
V1P8VCA
5
Part Number
Z@100MHz PkgSz DC res. Current(Ma)
2504021217Y0
120
0402
0.5
200
BLM15AG221SN1 220
0402
0.35
300
BLM15BB121SN1 120
0402
0.35
300
MMZ1005S241A
240
0402
0.18
200
TB4532153121
120
0402
0.3
300
C11
.1uF
C5
.1uF
1
SEE DATASHEET FOR BIAS NETWORK
V1P8VC
VDDD
VDDA
5
VDDO0
OUT0_SEL_I2CB
FOR LVDS, LVPECL AC COUPLE
USE TERMINATION ON RIGHT
Revision history
0.1 9/19/2014 first publication
Manufacture
Fair-Rite
muRata
muRata
TDK
TECSTAR
SD/OE
SEL1/SDA
SEL0/SCL
CLKSEL
CLKIN
CLKINB
XOUT
XIN/REF
U1
5P49V5925A
6
CLKIN
2
.1uF
1
2 CLKINB
C12
.1uF
8
9
SDA
SCL
1
C13
6
1
2
3
4
CLKSEL
CLKIN
CLKINB
FG_X1
FG_X2
NOTE:FERRITE BEAD FB1 =
FB1
1
2
SIGNAL_BEAD
VCC1P8
PLACE NEAR
I2C CONTROLLER
IF USED
SDA
SCL
R8
10K
V3P3
Use internal crystal
load capacitors
C6
6.8 pF
NO-POP
CL=8pF
C R25.000MHz
YSTAL_SMD
2
4 GND
GND
3
2
1
D
1
2
1
1
2
7
2
1
Y2
1
2
1
2
2
1
1
2
1
OUT_0_SEL-I2C
1
R10
1
R11
1
R12
R3
1
2
R5
49.9
1%
2
33
2
33
R15 1
R4
49.9
1%
2 33
OUT_2
2
1
2
1
2
1
3
Friday, September 19, 2014
Date:
2
Sheet
1
of
1
1
RECEIVER
U4
RECEIVER
U2
Integrated Device Technology
San Jose, CA
Document Number
5P49V5925A_SCH
Size
A
1
RECEIVER
U3
Layout notes.
1.Separate Xout and Xin traces
by 3 x the trace width.
2.Do not share crystal load
capacitor ground via with other
components.
3.Route power from bead through
bulk capacitor pad then through
0.1uF capacitor pad then to
clock chip Vdd pad.
4.Do not share ground vias. One
ground pin one ground via.
LVCMOS TERMINATION
OUTR2
HCSL TERMINATION
1
R13
1
R14
2
2
50
2
50
2
50
100
3.3V LVPECL TERMINATION
LVDS TERMINATION
2 33
3
2
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
2
1
2
25
26
27
28
29
30
31
32
33
1
2
1
2
1
19
2
2
1
FEBRUARY 21, 2019
1
8
Rev
0.1
A
B
C
D
5P49V5925 DATASHEET
5P49V5925 Applications Schematic
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Overdriving the XIN/REF Interface
LVCMOS Driver
The XIN/REF input can be overdriven by an LVCMOS driver
or by one side of a differential driver through an AC coupling
capacitor. The XOUT pin can be left floating. The amplitude of
the input signal should be between 500mV and 1.2V and the
slew rate should not be less than 0.2V/ns. Figure General
Diagram for LVCMOS Driver to XTAL Input Interface shows an
example of the interface diagram for a LVCMOS driver.
This configuration has three properties; the total output
impedance of Ro and Rs matches the 50 ohm transmission
line impedance, the Vrx voltage is generated at the CLKIN
inputs which maintains the LVCMOS driver voltage level
across the transmission line for best S/N and the R1-R2
voltage divider values ensure that the clock level at XIN is less
than the maximum value of 1.2V.
VDD
XOUT
Rs
Ro
Ro + Rs =
Zo = 50 Ohm
C3
R1
V_XIN
50 o hms
XIN / REF
0. 1 uF
LVCMOS
R2
General Diagram for LVCMOS Driver to XTAL Input Interface
Table 19 Nominal Voltage Divider Values vs LVCMOS VDD for
XIN shows resistor values that ensure the maximum drive
level for the XIN/REF port is not exceeded for all combinations
of 5% tolerance on the driver VDD, the VersaClock VDDA and
5% resistor tolerances. The values of the resistors can be
adjusted to reduce the loading for slower and weaker
LVCMOS driver by increasing the voltage divider attenuation
as long as the minimum drive level is maintained over all
tolerances. To assist this assessment, the total load on the
driver is included in the table.
Table 19: Nominal Voltage Divider Values vs LVCMOS VDD for XIN
LVCMOS Driver VDD
Ro+Rs
R1
R2
V_XIN (peak)
Ro+Rs+R1+R2
3.3
50.0
130
75
0.97
255
2.5
50.0
100
100
1.00
250
1.8
50.0
62
130
0.97
242
PROGRAMMABLE CLOCK GENERATOR
20
FEBRUARY 21, 2019
5P49V5925 DATASHEET
Wiring the Differential Input to Accept Single-Ended Levels
Figure Recommended Schematic for Wiring a Differential
Input to Accept Single-ended Levels shows how a differential
input can be wired to accept single ended levels. This
configuration has three properties; the total output impedance
of Ro and Rs matches the 50 ohm transmission line
impedance, the Vrx voltage is generated at the CLKIN inputs
which maintains the LVCMOS driver voltage level across the
transmission line for best S/N and the R1-R2 voltage divider
values ensure that Vrx p-p at CLKIN is less than the maximum
value of 1.2V.
VDD
Rs
Ro
Zo = 50 Ohm
R1
Vrx
CLKI N
Ro + Rs = 5 0
LVCMOS
CLKI NB
R2
Vers aCloc k 5 Rec eiver
Recommended Schematic for Wiring a Differential Input to Accept Single-ended Levels
Table 20 Nominal Voltage Divider Values vs Driver VDD
shows resistor values that ensure the maximum drive level for
the CLKIN port is not exceeded for all combinations of 5%
tolerance on the driver VDD, the VersaClock Vddo_0 and 5%
resistor tolerances. The values of the resistors can be
adjusted to reduce the loading for slower and weaker
LVCMOS driver by increasing the impedance of the R1-R2
divider. To assist this assessment, the total load on the driver
is included in the table.
Table 20: Nominal Voltage Divider Values vs Driver VDD
LVCMOS Driver VDD
Ro+Rs
R1
R2
Vrx (peak)
Ro+Rs+R1+R2
3.3
50.0
130
75
0.97
255
2.5
50.0
100
100
1.00
250
1.8
50.0
62
130
0.97
242
HCSL Differential Clock Input Interface
CLKIN/CLKINB will accept DC coupled HCSL signals.
Q
nQ
Zo=50ohm
CLKIN
Zo=50ohm
CLKINB
VersaClock 5 Receiver
CLKIN, CLKINB Input Driven by an HCSL Driver
FEBRUARY 21, 2019
21
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
3.3V Differential LVPECL Clock Input Interface
The logic levels of 3.3V LVPECL and LVDS can exceed VIH
max for the CLKIN/B pins. Therefore the LVPECL levels must
be AC coupled to the VersaClock differential input and the DC
bias restored with external voltage dividers. A single table of
bias resistor values is provided below for both for 3.3V
LVPECL and LVDS. Vbias can be VDDD, VDDOX or any other
available voltage at the VersaClock receiver that is most
conveniently accessible in layout.
Vbias
Rpu1
Rpu2
C5
0.01µF
Zo=50ohm
CLKIN
C6
0.01µF
Zo=50ohm
CLKINB
+3.3V LVPECL
Driver
R9
50ohm
R10
50ohm
VersaClock 5 Receiver
R13
4.7kohm
R15
4.7kohm
RTT
50ohm
CLKIN, CLKINB Input Driven by a 3.3V LVPECL Driver
Vbias
Rpu1
Rpu2
C1
0.1µF
Zo=50ohm
CLKIN
Zo=50ohm
Rterm
100ohm
C2
0.1µF
CLKINB
VersaClock 5 Receiver
LVDS Driver
R1
4.7kohm
R2
4.7kohm
CLKIN, CLKINB Input Driven by an LVDS Driver
Table 21: Bias Resistors for 3.3V LVPECL and LVDS Drive to CLKIN/B
Vbias
(V)
Rpu1/2
(kohm)
CLKIN/B Bias Voltage
(V)
3.3
22
0.58
2.5
15
0.60
1.8
10
0.58
PROGRAMMABLE CLOCK GENERATOR
22
FEBRUARY 21, 2019
5P49V5925 DATASHEET
2.5V Differential LVPECL Clock Input Interface
The maximum DC 2.5V LVPECL voltage meets the VIH max
CLKIN requirement. Therefore, 2.5V LVPECL can be
connected directly to the CLKIN terminals without AC coupling
Zo=50ohm
CLKIN
Zo=50ohm
CLKINB
+2.5V LVPECL
Driver
R1
50ohm
R2
50ohm
Versaclock 5 Receiver
RTT
18ohm
CLKIN, CLKINB Input Driven by a 2.5V LVPECL Driver
FEBRUARY 21, 2019
23
PROGRAMMABLE CLOCK GENERATOR
5P49V5925 DATASHEET
Package Outline Drawings
The package outline drawings are appended at the end of this document and are accessible from the link below. The package information is
the most current data available.
www.idt.com/document/psc/24-vfqfpn-package-outline-drawing-40-x-40-x-09-mm-body-05mm-pitch-epad-280-x-280-mm-nlg24p2
Marking Diagram
5925B
ddd
YWW**$
1. Line 1 is the truncated part number.
2. “ddd” denotes dash code.
3. “YWW” is the last digit of the year and week that the part was assembled.
4. “**” denotes lot number.
5. “$” denotes mark code.
Ordering Information
Part / Order Number
Shipping Packaging
Package
Temperature
5P49V5925BdddNLGI
5P49V5925BdddNLGI8
Tray
Tape and Reel
24-pin VFQFPN
24-pin VFQFPN
-40° to +85°C
-40° to +85°C
“G” after the two-letter package code denotes Pb-Free configuration, RoHS compliant.
Revision History
Date
February 21, 2019
Description of Change
Updated Package Outline Drawings section to include dynamic link and text.
August 9, 2017
Changed shipping packaging for NLGI from “Tubes” to “Tray”.
March 2, 2017
Updated POD and legal disclaimer.
February 24, 2017
1. Added “Output Alignment” section.
2. Update “Output Divides” section
PROGRAMMABLE CLOCK GENERATOR
24
FEBRUARY 21, 2019
Corporate Headquarters
Sales
Tech Support
6024 Silver Creek Valley Road
San Jose, CA 95138 USA
www.IDT.com
1-800-345-7015 or 408-284-8200
Fax: 408-284-2775
www.IDT.com/go/sales
www.idt.com/go/support
DISCLAIMER Integrated Device Technology, Inc. (IDT) and its affiliated companies (herein referred to as “IDT”) reserve the right to modify the products and/or specifications described herein at any time, without
notice, at IDT’s sole discretion. Performance specifications and operating parameters of the described products are determined in an independent state and are not guaranteed to perform the same way when installed
in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT's products for any
particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.
IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably
expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.
Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the property of
IDT or their respective third party owners. For datasheet type definitions and a glossary of common terms, visit www.idt.com/go/glossary. Integrated Device Technology, Inc. All rights reserved.
5P49V5925 FEBRUARY 21, 2019
25
©2019 Integrated Device Technology, Inc.
24-VFQFPN, Package Outline Drawing
4.0 x 4.0 x 0.90 mm Body,0.50mm Pitch,Epad 2.80 x 2.80 mm
NLG24P2, PSC-4192-02, Rev 02, Page 1
© Integrated Device Technology, Inc.
24-VFQFPN, Package Outline Drawing
4.0 x 4.0 x 0.90 mm Body,0.50mm Pitch,Epad 2.80 x 2.80 mm
NLG24P2, PSC-4192-02, Rev 02, Page 2
Package Revision History
© Integrated Device Technology, Inc.
Description
Date Created
Rev No.
Nov 2, 2018
Rev 02
New Format, Recalculate Land Pattern
Oct 12, 2016
Rev 01
Add Chamfer
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.