VersaClock® 6E Programmable
Clock Generator
5P49V6965
Datasheet
Description
Features
The 5P49V6965 is a programmable clock generator intended for
high-performance consumer, networking, industrial, computing,
and data-communications applications. Configurations may be
stored in on-chip One-Time Programmable (OTP) memory or
changed using I2C interface. This is Renesas’ sixth generation of
programmable clock technology (VersaClock 6E).
▪ Flexible 1.8V, 2.5V, 3.3V power-rails
▪ High-performance, low phase noise PLL, < 0.5ps RMS typical
phase jitter on outputs
▪ Four banks of internal OTP memory
• In-system or factory programmable
• 2 select pins accessible with processor GPIOs or
The frequencies are generated from a single reference clock. The
reference clock can come from one of the two redundant clock
inputs. A glitchless manual switchover function allows one of the
redundant clocks to be selected during normal operation.
bootstrapping
▪
I2C
•
serial programming interface
0xD0 or 0xD4 I2C address options allows multiple devices
configured in a same system
Two select pins allow up to four different configurations to be
programmed and accessible using processor GPIOs or
bootstrapping. The different selections may be used for different
operating modes (full function, partial function, partial
power-down), regional standards (US, Japan, Europe) or system
production margin testing. The device may be configured to use
one of two I2C addresses to allow multiple devices to be used in a
system.
▪ Reference LVCMOS output clock
▪ Four universal output pairs individually configurable:
Typical Applications
▪ Output frequency ranges:
▪
▪
▪
▪
▪
▪
▪
▪
▪
▪
▪
• Differential (LVPECL, LVDS or HCSL)
• 2 single-ended (2 LVCMOS in-phase or 180 degrees out of
phase)
• I/O VDDs can be mixed and matched, supporting 1.8V
(LVDS and LVCMOS), 2.5V, or 3.3V
• LVCMOS clock outputs: 1kHz to 200MHz
• LVDS, LVPECL, HCSL differential clock outputs: 1kHz to
Ethernet switch/router
PCI Express 1.0 / 2.0 / 3.0 / 4.0 Spread Spectrum on
PCI Express 1.0 / 2.0 / 3.0 / 4.0 / 5.0 Spread Spectrum off
Broadcast video/audio timing
Multi-function printer
Processor and FPGA clocking
Any-frequency clock conversion
MSAN/DSLAM/PON
Fiber Channel, SAN
Telecom line cards
Laser distance sensing
350MHz
▪
▪
▪
▪
Redundant clock inputs with manual switchover
Programmable output enable or power-down mode
Available in 4 × 4 mm 24-VFQFPN package
-40° to +85°C industrial temperature operation
Block Diagram
VDDO 0
XIN/REF
OUT0_SEL_I2CB
VDDO1
XOUT
OUT1
CLKIN
FOD1
OUT1B
CLKINB
VDDO2
CLKSEL
OUT2
SD/OE
SEL1/SDA
SEL0/SCL
OTP
and
Control
Logic
FOD2
OUT2B
PLL
VDDO3
OUT3
VDDA
FOD3
OUT3B
VDDD
V DDO4
OUT4
FOD4
OUT4B
©2021 Renesas Electronics Corporation
1
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Contents
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin Assignments. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
I2C Bus Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Test Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Jitter Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PCI Express Jitter Performance and Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Features and Functional Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Device Startup and Power-On-Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Reference Clock and Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Manual Switchover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Internal Crystal Oscillator (XIN/REF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Programmable Loop Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Fractional Output Dividers (FOD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Output Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SD/OE Pin Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
I2C Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Typical Application Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Input – Driving the XIN/REF or CLKIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Output – Single-ended or Differential Clock Terminations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Package Outline Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Marking Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
©2021 Renesas Electronics Corporation
2
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Pin Assignments
VDDA
5
CLKSEL
6
VDDO1
VDDD
OUT1B
4
EPAD
7
VDDO2
17
OUT2
16
OUT2B
15
VDDO3
14
OUT3
13
OUT3B
8
9
10
11
12
OUT4B
XIN/REF
OUT1
3
18
OUT4
XOUT
19
VDDO4
2
21 20
SEL0/SCL
CLKINB
24 23 22
SEL1/SDA
1
SD/OE
CLKIN
VDDO0
OUT0_SEL_I2CB
Figure 1. Pin Assignments for 4 x 4 mm 24-VFQFPN Package – Top View
4 × 4 mm 24-VFQFPN
Pin Descriptions
Table 1. Pin Descriptions
Number
Name
Type
Description
1
CLKIN
Input
Internal
Pull-down
Differential clock input. Weak 100kΩ internal pull-down.
2
CLKINB
Input
Internal
Pull-down
Complementary differential clock input. Weak 100kΩ internal pull-down.
3
XOUT
Output
4
XIN/REF
Input
Crystal oscillator interface input, or single-ended LVCMOS clock input. Input voltage needs
to be below 1.2V. Refer to the section Driving XIN/REF with a CMOS Driver.
5
VDDA
Power
Analog functions power supply pin. Connect to 1.8V to 3.3V. VDDA and VDDD should have
the same voltage applied.
Crystal oscillator interface output.
Input clock select. Selects the active input reference source in manual switchover mode.
0 = XIN/REF, XOUT (default).
1 = CLKIN, CLKINB.
See Table 20. Input Clock Select for more details.
6
CLKSEL
Input
Internal
Pull-down
7
SD/OE
Input
Internal
Pull-down
Enables/disables the outputs (OE) or powers down the chip (SD).
8
SEL1/SDA
Input
Internal
Pull-down
Configuration select pin, or I2C SDA input as selected by OUT0_SEL_I2CB. Weak internal
pull-down resistor.
9
SEL0/SCL
Input
Internal
Pull-down
Configuration select pin, or I2C SCL input as selected by OUT0_SEL_I2CB. Weak internal
pull-down resistor.
©2021 Renesas Electronics Corporation
3
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Table 1. Pin Descriptions (Cont.)
Number
Name
Type
Description
10
VDDO4
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT4/OUT4B.
11
OUT4
Output
Output clock 4. Refer to the Output Drivers section for more details.
12
OUT4B
Output
Complementary output clock 4. Refer to the Output Drivers section for more details.
13
OUT3B
Output
Complementary output clock 3. Refer to the Output Drivers section for more details.
14
OUT3
Output
Output clock 3. Refer to the Output Drivers section for more details.
15
VDDO3
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT3/OUT3B.
16
OUT2B
Output
Complementary output clock 2. Refer to the Output Drivers section for more details.
17
OUT2
Output
Output clock 2. Refer to the Output Drivers section for more details.
18
VDDO2
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT2/OUT2B.
19
OUT1B
Output
Complementary output clock 1. Refer to the Output Drivers section for more details.
20
OUT1
Output
Output clock 1. Refer to the Output Drivers section for more details.
21
VDDO1
Power
Output power supply. Connect to 1.8 to 3.3V. Sets output voltage levels for OUT1/OUT1B.
22
VDDD
Power
Digital functions power supply pin. Connect to 1.8 to 3.3V. VDDA and VDDD should have the
same voltage applied.
23
VDDO0
Power
Power supply pin for OUT0_SEL_I2CB. Connect to 1.8 to 3.3V. Sets output voltage levels
for OUT0.
24
OUT0_SEL
_I2CB
25
GND
Input/
Output
Internal
Pull-down
GND
©2021 Renesas Electronics Corporation
Latched input/LVCMOS output. At power-up, the voltage at the pin OUT0_SEL_I2CB is
latched by the part and used to select the state of pins 8 and 9. If a weak pull-up (10kΩ) is
placed on OUT0_SEL_I2CB, pins 8 and 9 will be configured as hardware select pins, SEL1
and SEL0. If a weak pull-down (10kΩ) is placed on OUT0_SEL_I2CB or it is left floating,
pins 8 and 9 will act as the SDA and SCL pins of an I2C interface. After power-up, the pin
acts as an LVCMOS reference output.
Connect to ground pad.
4
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Absolute Maximum Ratings
The absolute maximum ratings are stress ratings only. Stresses greater than those listed below can cause permanent damage to the
device. Functional operation of the device at absolute maximum ratings is not implied. Exposure to absolute maximum rating conditions
may affect device reliability.
Table 2. Absolute Maximum Ratings
Item
Rating
Supply Voltage, V DDA, VDDD, VDDO
3.6V.
XIN/REF Input
1.2V.
CLKIN, CLKINB Input
VDDO0, 1.2V voltage swing.
2
I C Loading Current
10mA.
Storage Temperature, T STG
-65°C to 150°C.
Junction Temperature
125°C
ESD Human Body Model
2000V.
Thermal Characteristics
Table 3. Thermal Characteristics
Symbol
Parameter
Value
Units
42
°C/W
θJA
Theta JA. Junction to air thermal impedance (0mps).
θJB
Theta JB. Junction to board thermal impedance (0mps).
2.35
°C/W
θJC
Theta JC. Junction to case thermal impedance (0mps).
41.8
°C/W
Recommended Operating Conditions
Table 4. Recommended Operating Conditions
Symbol
Minimum
Typical
Maximum
Units
Power supply voltage for supporting 1.8V outputs.
1.71
1.8
1.89
V
Power supply voltage for supporting 2.5V outputs.
2.375
2.5
2.625
V
Power supply voltage for supporting 3.3V outputs.
3.135
3.3
3.465
V
VDDD
Power supply voltage for core logic functions.
1.71
3.465
V
VDDA
Analog power supply voltage. Use filtered analog power supply.
1.71
3.465
V
TPU
Power ramp time for all VDDs to reach 90% of VDD.
0.05
50
ms
TA
Operating temperature, ambient.
-40
85
°C
CL
Maximum load capacitance (3.3V LVCMOS only).
15
pF
VDDOX
Parameter
©2021 Renesas Electronics Corporation
5
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Electrical Characteristics
Table 5. Current Consumption
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, 1.8V ±5%, TA = -40°C to +85°C.
Symbol
IDDCORE 1
Parameter
Core Supply Current
Conditions
Minimum
Typical
Maximum
Units
33
42
mA
45
58
mA
LVPECL, 350MHz, 2.5V VDDOx.2.
36
47
mA
LVDS, 350MHz, 3.3V VDDOx
.
26
32
mA
.
25
30
mA
22
27
mA
39
48
mA
100MHz on all outputs, 25MHz REFCLK.
LVPECL, 350MHz, 3.3V VDDOx.
LVDS, 350MHz, 2.5V VDDOx
2
2
2
.
LVDS, 350MHz, 1.8V VDDOx2.
IDDOx
Output Buffer Supply
Current
HCSL, 250MHz, 3.3V VDDOx
2
.
HCSL, 250MHz, 2.5V VDDOx 2.
37
46
mA
2,3.
22
27
mA
2,3.
20
24
mA
LVCMOS, 50MHz, 1.8V, VDDOx 2,3.
17
21
mA
LVCMOS, 200MHz, 3.3V VDDOx
2,3.
43
56
mA
2,3.
33
43
mA
LVCMOS, 200MHz, 1.8V VDDOx 2,3.
24
31
mA
SD asserted,
10
12
mA
LVCMOS, 50MHz, 3.3V, VDDOx
LVCMOS, 50MHz, 2.5V, VDDOx
LVCMOS, 200MHz, 2.5V VDDOx
IDDPD
1
2
3
Power Down Current
I2C
programming.
IDDCORE = IDDA + IDDD.
Measured into a 5” 50Ω trace. See Test Loads section for more details.
Single CMOS driver active.
©2021 Renesas Electronics Corporation
6
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Table 6. AC Timing Characteristics
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, 1.8V ±5%, TA = -40°C to +85°C unless stated otherwise.
Symbol
FIN
1
FOUT 2
fVCO
TDC 3
Parameter
Input Frequency
Output Frequency
Output Duty Cycle
Output Skew
TSTARTUP 4,5
Startup Time
2
3
4
5
6
Minimum
Typical
Maximum
Units
Input frequency limit (crystal).
8
40
MHz
Input frequency limit (CLKIN,CLKINB).
1
350
MHz
Input frequency limit (single-ended over XIN).
1
200
MHz
Single-ended clock output limit (LVCMOS),
individual FOD mode.
1
200
Differential clock output limit
(LVPECL/LVDS/HCSL), individual FOD mode.
1
350
Single-ended clock output limit (LVCMOS),
cascaded FOD mode, output 2–4.
0.001
200
Differential clock output limit
(LVPECL/LVDS/HCSL), cascaded FOD mode,
output 2–4.
0.001
350
2500
2900
MHz
VCO Operating Frequency
Range
TSKEW
1
Conditions
MHz
Measured at VDD/2, all outputs except
reference output, VDDOX = 2.5V or 3.3V.
45
50
55
%
Measured at VDD/2, all outputs except
reference output, VDDOX = 1.8V
40
50
60
%
Measured at VDD/2, reference output OUT0
(5MHz–150.1MHz) with 50% duty cycle input.
40
50
60
%
Measured at VDD/2, reference output OUT0
(150.1MHz–200MHz) with 50% duty cycle
input.
30
50
70
%
Skew between the same frequencies, with
outputs using the same driver format and
phase delay set to 0ns.
75
Measured after all VDDs have risen above
90% of their target value 6.
PLL lock time from shutdown mode.
3
ps
30
ms
4
ms
Practical lower frequency is determined by loop filter settings.
A slew rate of 2.75V/ns or greater should be selected for output frequencies of 100MHz or higher.
Duty cycle is only guaranteed at maximum slew rate settings.
Actual PLL lock time depends on the loop configuration.
Includes loading the configuration bits from EPROM to PLL registers. It does not include EPROM programming/write time.
Power-up with temperature calibration enabled; contact Renesas if shorter lock-time is required in system.
©2021 Renesas Electronics Corporation
7
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Table 7. General Input Characteristics
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, 1.8V ±5%, TA = -40°C to +85°C unless stated otherwise.
Symbol
Parameter
Conditions
Minimum
Typical
Maximum
Units
3
7
pF
100
300
kΩ
CIN
Input Capacitance
CLKIN,CLKINB,CLKSEL,SD/OE,SEL1/SD
A, SEL0/SCL.
RPD
Pull-down Resistor
CLKSEL, SD/OE, SEL1/SDA, SEL0/SCL,
CLKIN, CLKINB, OUT0_SEL_I2CB.
VIH
Input High Voltage
CLKSEL, SD/OE.
0.7 x VDDD
VDDD + 0.3
V
VIL
Input Low Voltage
CLKSEL, SD/OE.
GND - 0.3
0.3 x VDDD
V
VIH
Input High Voltage
OUT0_SEL_I2CB.
1.7
VDDO0 + 0.3
V
VIL
Input Low Voltage
OUT0_SEL_I2CB.
GND - 0.3
0.4
V
VIH
Input High Voltage
XIN/REF.
0.8
1.2
V
VIL
Input Low Voltage
XIN/REF.
GND - 0.3
0.4
V
Input Rise/Fall Time
CLKSEL, SD/OE, SEL1/SDA, SEL0/SCL.
300
ns
Maximum
Units
TR/TF
Table 8. CLKIN Electrical Characteristics
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, 1.8V ±5%, TA = -40°C to +85°C unless stated otherwise.
Symbol
Parameter
Conditions
Minimum
Typical
VSWING
Input Amplitude – CLKIN, CLKINB
Peak to peak value, single-ended.
200
1200
mV
dv/dt
Input Slew Rate – CLKIN, CLKINB
Measured differentially.
0.4
8
V/ns
IIL
Input Leakage Low Current
VIN = GND.
-5
5
μA
IIH
Input Leakage High Current
VIN = 1.7V.
20
μA
Input Duty Cycle
Measurement from differential
waveform.
55
%
DCIN
©2021 Renesas Electronics Corporation
8
45
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Table 9. Electrical Characteristics – CMOS Outputs
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, 1.8V ±5%, TA = -40°C to +85°C unless stated otherwise.
Symbol
Parameter
Conditions
0.7 x VDDO
VDDO
V
IOH = -8mA (1.8V).
0.5 x VDDO
VDDO
V
0.45
V
Output High Voltage
VOL
Output Low Voltage
IOL = 15mA (3.3V), 12mA (2.5V), 8mA (1.8V).
ROUT
Output Driver Impedance
CMOS output driver.
17
Slew Rate, SLEW[1:0] = 00
Slew Rate, SLEW[1:0] = 10
Slew Rate, SLEW[1:0] = 11
Single-ended 3.3V LVCMOS output clock rise and
fall time, 20% to 80% of VDDO (output load = 5pF)
VDDOX = 3.3V.
Slew Rate, SLEW[1:0] = 00
TSR
Slew Rate, SLEW[1:0] = 01
Slew Rate, SLEW[1:0] = 10
Slew Rate, SLEW[1:0] = 11
Single-ended 2.5V LVCMOS output clock rise and
fall time, 20% to 80% of VDDO (output load = 5pF)
VDDOX = 2.5V.
Slew Rate, SLEW[1:0] = 00
Slew Rate, SLEW[1:0] = 01
Slew Rate, SLEW[1:0] = 10
Slew Rate, SLEW[1:0] = 11
IOZDD
Typical Maximum Units
IOH = -15mA (3.3V), -12mA (2.5V).
VOH
Slew Rate, SLEW[1:0] = 01
Minimum
Single-ended 1.8V LVCMOS output clock rise and
fall time, 20% to 80% of VDDO (output load = 5pF)
VDD = 1.8V.
1.0
2.2
1.2
2.3
1.3
2.4
1.7
2.7
0.6
1.3
0.7
1.4
0.6
1.4
1.0
1.7
0.3
0.7
0.4
0.8
0.4
0.9
0.7
1.2
Ω
V/ns
Output Leakage Current
(OUT1–4)
Tri-state outputs.
5
μA
Output Leakage Current (OUT0)
Tri-state outputs.
30
μA
Maximum
Units
Table 10. Electrical Characteristics – LVDS Outputs
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, 1.8V ±5%, TA = -40°C to +85°C unless stated otherwise.
Symbol
Parameter
Minimum
Typical
VOT (+)
Differential Output Voltage for the TRUE Binary State
247
454
mV
VOT (-)
Differential Output Voltage for the FALSE Binary State
-454
-247
mV
ΔVOT
Change in VOT between Complimentary Output States
50
mV
VOS
ΔVOS
Output Common Mode Voltage (Offset Voltage) at 3.3 V ±5%, 2.5V ±5%
Output Common Mode Voltage (Offset Voltage) at 1.8V ±5%
1.125
1.25
1.375
V
0.8
0.875
0.96
V
50
mV
Change in VOS between Complimentary Output States
IOS
Outputs Short Circuit Current, V OUT+ or VOUT - = 0V or VDDO
9
24
mA
IOSD
Differential Outputs Short Circuit Current, VOUT+ = VOUT -
6
12
mA
TR
LVDS rise time 20%–80%
300
ps
TF
LVDS fall time 80%–20%
300
ps
©2021 Renesas Electronics Corporation
9
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Table 11. Electrical Characteristics – LVPECL Outputs
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, TA = -40°C to +85°C unless stated otherwise.
Symbol
Parameter
Minimum
Typical
Maximum
Units
VOH
Output Voltage High, Terminated through 50Ω tied to VDD - 2V
VDDO - 1.19
VDDO - 0.69
V
VOL
Output Voltage Low, Terminated through 50Ω tied to VDD - 2V
VDDO - 1.94
VDDO - 1.4
V
1.1
2
V
VSWING
Peak-to-Peak Differential Output Voltage Swing
TR
LVPECL rise time 20%–80%
400
ps
TF
LVPECL fall time 80%–20%
400
ps
Table 12. Electrical Characteristics – HCSL Outputs
1
VDDA, VDDD, VDDO0 = 3.3V ±5%, 2.5V ±5%, TA = -40°C to +85°C unless stated otherwise.
Symbol
dV/dt
Parameter
Conditions
Scope averaging on 2,3.
Slew Rate
Minimum
Scope averaging on
VMAX
Maximum Voltage
VMIN
Minimum Voltage
Measurement on single-ended signal using absolute
value (scope averaging off).
2,6
4
V/ns
20
%
1150
mV
-300
mV
mV
VSWING
Voltage Swing
Scope averaging off
.
300
VCROSS
Crossing Voltage Value
Scope averaging off 4,6 .
250
ΔVCROSS
Crossing Voltage Variation
2
Units
1
Slew Rate Matching
1
Maximum
2,3.
ΔdV/dt
Scope averaging off
Typical
5.
550
mV
140
mV
Guaranteed by design and characterization. Not 100% tested in production.
Measured from differential waveform.
3 Slew
rate is measured through the VSWING voltage range centered around differential 0V. This results in a ±150mV window around differential 0V.
4V
CROSS is defined as voltage where Clock = Clock# measured on a component test board and only applies to the differential rising edge (i.e. Clock
rising and Clock# falling).
5 The total variation of all V
6
CROSS measurements in any particular system. Note that this is a subset of VCROSS min/max (V CROSS absolute) allowed.
The intent is to limit VCROSS induced modulation by setting ΔVCROSS to be smaller than VCROSS absolute.
Measured from single-ended waveform.
Table 13. Spread Spectrum Generation Specifications
Symbol
fSSOUT
fMOD
fSPREAD
Parameter
Conditions
Spread Frequency
Output frequency range for spread spectrum.
Mod Frequency
Modulation frequency.
Spread Value
Minimum
Typical
Maximum
Units
300
MHz
5
30 to 63
Amount of spread value (programmable)–center spread.
±0.1% to ±2.5%
Amount of spread value (programmable)–down spread.
-0.2% to -5%
©2021 Renesas Electronics Corporation
10
kHz
%fOUT
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
I2C Bus Characteristics
Table 14. I2C Bus (SCL/SDA) DC Characteristics
Symbol
Parameter
Conditions
VIH
Input High Level
For SEL1/SDA pin and
SEL0/SCL pin.
VIL
Input Low Level
For SEL1/SDA pin and
SEL0/SCL pin.
VHYS
Hysteresis of Inputs
IIN
Input Leakage Current
VOL
Output Low Voltage
Minimum
Typical
Maximum
0.7 x VDDD
Units
V
0.3 x VDDD
0.05 x VDDD
V
V
-1
IOL = 3mA.
36
μA
0.45
V
Maximum
Units
400
kHz
Table 15. I2C Bus (SCL/SDA) AC Characteristics
Symbol
Conditions
Minimum
Serial Clock Frequency (SCL)
—
10
Bus Free Time between Stop and Start
—
1.3
μs
tSU:START
Setup Time, Start
—
0.6
μs
tHD:START
Hold Time, Start
—
0.6
μs
tSU:DATA
Setup Time, Data Input (SDA)
—
0.1
μs
tHD:DATA
Hold Time, Data Input (SDA) 1
—
0
μs
tOVD
Output Data Valid from Clock
—
0.9
μs
CB
Capacitive Load for Each Bus Line
—
400
pF
tR
Rise Time, Data and Clock (SDA, SCL)
—
20 + 0.1 x CB
300
ns
tF
Fall Time, Data and Clock (SDA, SCL)
—
20 + 0.1 x CB
300
ns
tHIGH
High Time, Clock (SCL)
—
0.6
μs
tLOW
Low Time, Clock (SCL)
—
1.3
μs
Setup Time, Stop
—
0.6
μs
FSCLK
tBUF
tSU:STOP
Parameter
Typical
1 A device must internally
provide a hold time of at least 300ns for the SDA signal (referred to the VIH(MIN) of the SCL signal) to bridge the undefined
region of the falling edge of SCL.
2 I2 C
inputs are 3.3V tolerant.
©2021 Renesas Electronics Corporation
11
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Test Loads
Figure 2. LVCMOS Test Load
Test
Point
33 Ohm
Zo = 50 Ohm
5pF
Device
Figure 3. HCSL Test Load
50 Ohm
33 Ohm
2pF
Differential
Zo = 100 Ohm
33 Ohm
Test
Points
50 Ohm
2pF
Device
Figure 4. LVDS Test Load
2pF
Differential
Zo = 100 Ohm
100 Ohm Test
Points
2pF
Device
Figure 5. LVPECL Test Load
Differential
Zo = 100 Ohm
Test
Points
2pF
Device
©2021 Renesas Electronics Corporation
50Ohm
R
12
50 Ohm
2pF
R = 50 Ohm for 3.3V LVPECL
R = 18 Ohm for 2.5V LVPECL
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Jitter Performance Characteristics
Figure 6. Typical Phase Jitter Plot at 156.25MHz
Note: Measured with OUT2 = 156.25MHz on, 39.625MHz input.
Table 16. Jitter Performance
Symbol
1,2
Parameter
JCY-CY
Cycle to Cycle Jitter
JPK-PK
Period Jitter
JRMS
RMS Phase Jitter (12kHz–20MHz)
1
2
Conditions
Minimum
Typical
Maximum Units
LVCMOS 3.3V ±5%, -40°C–90°C.
5
30
ps
All differential outputs 3.3V ±5%, -40°C–90°C.
25
35
ps
LVCMOS 3.3V ±5%, -40°C–90°C.
28
40
ps
All differential outputs 3.3V ±5%, -40°C–90°C.
4
30
ps
LVCMOS 3.3V ±5%, -40°C–90°C.
0.3
ps
All differential outputs 3.3V ±5%, -40°C–90°C.
0.5
ps
Measured with 25MHz crystal input.
Configured with OUT0 = 25MHz–LVCMOS; OUT1 = 100MHz–HCSL; OUT2 = 125MHz–LVDS; OUT3 = 156.25MHz–LVPECL.
©2021 Renesas Electronics Corporation
13
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
PCI Express Jitter Performance and Specification
Table 17. PCI Express Jitter Performance (Spread Spectrum = Off)
Parameter
Symbol
Conditions
tjphPCIeG1-CC
PCIe Gen1 (2.5 GT/s)
SSC = OFF
Limit
Units
Notes
4
86
ps
(p-p)
1,2
PCIe Gen2 Lo Band (5.0 GT/s)
SSC = OFF
0.05
3
ps
(RMS)
1,2
PCIe Gen2 Hi Band (5.0 GT/s)
SSC = OFF
0.22
3.1
ps
(RMS)
1,2
tjphPCIeG3-CC
PCIe Gen3 (8.0 GT/s)
SSC = OFF
0.12
1
ps
(RMS)
1,2
tjphPCIeG4-CC
PCIe Gen4 (16.0 GT/s)
SSC = OFF
0.12
0.5
ps
(RMS)
1,2,3,4
tjphPCIeG5-CC
PCIe Gen5 (32.0 GT/s)
SSC = OFF
0.05
0.15
ps
(RMS)
1,2,3,5
tjphPCIeG1-SRNS
PCIe Gen1 (2.5 GT/s)
SSC = OFF
0.3
ps
(p-p)
1,2,6
tjphPCIeG2-SRNS
PCIe Gen2 (5.0 GT/s)
SSC = OFF
0.26
ps
(RMS)
1,2,6
PCIe Phase Jitter
t
(SRNS Architectures) jphPCIeG3-SRNS
PCIe Gen3 (8.0 GT/s)
SSC = OFF
0.07
ps
(RMS)
1,2,6
tjphPCIeG4-SRNS
PCIe Gen4 (16.0 GT/s)
SSC = OFF
0.07
ps
(RMS)
1,2,6
tjphPCIeG5-SRNS
PCIe Gen5 (32.0 GT/s)
SSC = OFF
0.07
ps
(RMS)
1,2,6
tjphPCIeG2-CC
PCIe Phase Jitter
(Common Clocked
Architectures)
Minimum
Typical Maximum
N/A
1 The Refclk jitter is measured after applying the filter functions found in PCI Express Base Specification 5.0, Revision 1.0. See the Test Loads section
2
3
4
5
6
of the data sheet for the exact measurement setup. The worst case results for each data rate are summarized in this table.
Jitter measurements shall be made with a capture of at least 100,000 clock cycles captured by a real-time oscilloscope (RTO) with a sample rate
of 20GS/s or greater. Broadband oscilloscope noise must be minimized in the measurement. The measured PP jitter is used (no extrapolation) for
RTO measurements. Alternately, jitter measurements may be used with a Phase Noise Analyzer (PNA) extending (flat) and integrating and folding
the frequency content up to an offset from the carrier frequency of at least 200MHz (at 300MHz absolute frequency) below the Nyquist frequency.
For PNA measurements for the 2.5GT/s data rate, the RMS jitter is converted to peak to peak jitter using a multiplication factor of 8.83. In the case
where real-time oscilloscope and PNA measurements have both been done and produce different results, the RTO result must be used.
SSC spurs from the fundamental and harmonics are removed up to a cutoff frequency of 2MHz taking care to minimize removal of any non-SSC
content.
Note that 0.7ps RMS is to be used in channel simulations to account for additional noise in a real system.
Note that 0.25ps RMS is to be used in channel simulations to account for additional noise in a real system.
While the PCI Express Base Specification 5.0, Revision 1.0 provides the filters necessary to calculate SRIS jitter values, it does not provide
specification limits, hence the n/a in the Limit column. SRIS values are informative only. In general, a clock operating in an SRIS system must be
twice as good as a clock operating in a Common Clock system. For RMS values, twice as good is equivalent to dividing the CC value by Ö2.
©2021 Renesas Electronics Corporation
14
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Table 18. PCI Express Jitter Performance (Spread Spectrum = On)
Parameter
Symbol
Conditions
tjphPCIeG1-CC
PCIe Gen 1 (2.5 GT/s)
SSC ≤ -0.5%
Limit
Units
Notes
16
86
ps
(p-p)
1,2
PCIe Gen 2 Lo Band (5.0 GT/s)
SSC ≤ -0.5%
0.02
3
ps
(RMS)
1,2
PCIe Gen 2 Hi Band (5.0 GT/s)
SSC ≤ -0.5%
0.92
3.1
ps
(RMS)
1,2
tjphPCIeG3-CC
PCIe Gen 3 (8.0 GT/s)
SSC ≤ -0.5%
0.37
1
ps
(RMS)
1,2
tjphPCIeG4-CC
PCIe Gen 4 (16.0 GT/s)
SSC ≤ -0.5%
0.37
0.5
ps
(RMS)
1,2,3,4
tjphPCIeG5-CC
PCIe Gen 5 (32.0 GT/s)
SSC ≤ -0.5%
N/A
0.15
ps
(RMS)
1,2,3,5
tjphPCIeG1-SRIS
PCIe Gen 1 (2.5 GT/s)
SSC ≤ -0.3%
14
ps
(p-p)
1,2,6
tjphPCIeG2-SRIS
PCIe Gen 2 (5.0 GT/s)
SSC ≤ -0.3%
1.4
ps
(RMS)
1,2,6
tjphPCIeG3-SRIS
PCIe Gen 3 (8.0 GT/s)
SSC ≤ -0.3%
0.42
ps
(RMS)
1,2,6
tjphPCIeG4-SRIS
PCIe Gen 4 (16.0 GT/s)
SSC ≤ -0.3%
0.36
ps
(RMS)
1,2,6
tjphPCIeG5-SRIS
PCIe Gen 5 (32.0 GT/s)
SSC ≤ -0.3%
N/A
ps
(RMS)
1,2,6
tjphPCIeG2-CC
PCIe Phase Jitter
(Common Clocked
Architectures)
PCIe Phase Jitter
(SRIS Architectures)
1
2
3
4
5
6
Minimum
Typical Maximum
N/A
The Refclk jitter is measured after applying the filter functions found in PCI Express Base Specification 5.0, Revision 1.0. See the Test Loads section
of the data sheet for the exact measurement setup. The worst case results for each data rate are summarized in this table.
Jitter measurements shall be made with a capture of at least 100,000 clock cycles captured by a real-time oscilloscope (RTO) with a sample rate
of 20GS/s or greater. Broadband oscilloscope noise must be minimized in the measurement. The measured PP jitter is used (no extrapolation) for
RTO measurements. Alternately, jitter measurements may be used with a Phase Noise Analyzer (PNA) extending (flat) and integrating and folding
the frequency content up to an offset from the carrier frequency of at least 200MHz (at 300MHz absolute frequency) below the Nyquist frequency.
For PNA measurements for the 2.5GT/s data rate, the RMS jitter is converted to peak to peak jitter using a multiplication factor of 8.83. In the case
where real-time oscilloscope and PNA measurements have both been done and produce different results, the RTO result must be used.
SSC spurs from the fundamental and harmonics are removed up to a cutoff frequency of 2MHz taking care to minimize removal of any non-SSC
content.
Note that 0.7ps RMS is to be used in channel simulations to account for additional noise in a real system.
Note that 0.25ps RMS is to be used in channel simulations to account for additional noise in a real system.
While the PCI Express Base Specification 5.0, Revision 1.0 provides the filters necessary to calculate SRIS jitter values, it does not provide
specification limits, hence the n/a in the Limit column. SRIS values are informative only. In general, a clock operating in an SRIS system must be
twice as good as a clock operating in a Common Clock system. For RMS values, twice as good is equivalent to dividing the CC value by Ö2.
©2021 Renesas Electronics Corporation
15
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Features and Functional Blocks
Device Startup and Power-On-Reset
Reference Clock and Selection
The device has an internal power-up reset (POR) circuit. All V DDs
must be connected to desired supply voltage to trigger POR.
The device supports up to two clock inputs.
▪ Crystal input, can be driven by a single-ended clock.
▪ Clock input (CLKIN, CLKINB), a fully differential input that only
accepts a reference clock. A single-ended clock can also drive
it on CLKIN.
User can define specific default configurations through internal
One-Time-Programmable (OTP) memory. Either customer or
factory can program the default configuration. Please refer to
VersaClock 6E Family Register Descriptions and Programming
Guide for details or contact Renesas if a specific
factory-programmed default configuration is required.
Figure 7. Clock Input Diagram, Internal Logic
XIN/REF
Device will identity which of the 2 modes to operate in by the state
of OUT0_SEL_I2CB pin at POR. Both of the 2 modes default
configurations can be programmed as stated above.
XOUT
1. Software Mode (I2C): OUT0_SEL_I2CB is low at POR.
CLKIN
I2C interface will be open to users for in-system programming,
overriding device default configurations at any time.
CLKINB
2. Hardware Select Mode: OUT0_SEL_I2CB is high at POR.
Device has been programmed to load OTP at power-up
(REG0[7]=1). The device will load internal registers according
to Table 19. Power-up Behavior.
Internal OTP memory can support up to 4 configurations,
selectable by SEL0/SEL1 pins.
At POR, logic levels at SEL0 and SEL1 pins must be settled,
resulting the selected configuration to be loaded at power up.
After the first 10ms of operation, the levels of the SELx pins
can be changed, either to low or to the same level as
VDDD/VDDA. The SELx pins must be driven with a digital signal
of < 300ns rise/fall time and only a single pin can be changed
at a time. After a pin level change, the device must not be
interrupted for at least 1ms so that the new values have time to
load and take effect.
CLKSEL
OUT0_SEL_I2CB
at POR
SEL1
SEL0
Access
REG0:7
Config
1
0
0
No
0
0
1
0
1
No
0
1
1
1
0
No
0
2
1
1
1
No
0
3
0
X
X
Yes
1
I2C
defaults
0
X
X
Yes
0
0
©2021 Renesas Electronics Corporation
OTP
and
Control
Logic
Manual Switchover
The CLKSEL pin selects the input clock between either XTAL/REF
or (CLKIN, CLKINB).
CLKSEL polarity can be changed by I2C programming (Byte
0x13[1]) as shown in the table below.
0 = XIN/REF, XOUT (default); 1 = CLKIN, CLKINB.
Table 20. Input Clock Select
Table 19. Power-up Behavior
I2C
PRIMSRC
Reg 0x13[1]
PRIMSRC
CLKSEL
Source
0
0
XIN/REF
0
1
CLKIN, CLKINB
1
0
CLKIN, CLKINB
1
1
XIN/REF
When SM[1:0] is “0x”, the redundant inputs are in manual
switchover mode. In this mode, CLKSEL pin is used to switch
between the primary and secondary clock sources. The PRIMSRC
bit determines the primary and secondary clock source setting.
During the switchover, no glitches will occur at the output of the
device, although there may be frequency and phase drift,
depending on the exact phase and frequency relationship
between the primary and secondary clocks.
16
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Internal Crystal Oscillator (XIN/REF)
Ci1 and Ci2 are commonly programmed to be the same value.
Adjustment of the crystal tuning capacitors allows maximum
flexibility to accommodate crystals from various manufacturers.
The range of tuning capacitor values available are in accordance
with the following table.
Choosing Crystals
A crystal manufacturer will calibrate its crystals to the nominal
frequency with a certain load capacitance value. When the
oscillator load capacitance matches the crystal load capacitance,
the oscillation frequency will be accurate. When the oscillator load
capacitance is lower than the crystal load capacitance, the
oscillation frequency will be higher than nominal and vice versa so
for an accurate oscillation frequency you need to make sure to
match the oscillator load capacitance with the crystal load
capacitance.
Ci1/Ci2 starts at 9pF with setting 000000b and can be increased
up to 25pF with setting 111111b. The step per bit is 0.5pF.
Table 21. XTAL[5:0] Tuning Capacitor
Tuning the Crystal Load Capacitor
Parameter
Bits
Step (pF)
Minimum (pF)
Maximum (pF)
XTAL
6
0.5
9
25
You can write the following equation for this capacitance:
Ci = 9pF + 0.5pF × XTAL[5:0]
CXIN = Ci1 + Cs1 + Ce1
CXOUT = Ci2 + Cs2 + Ce2
The final load capacitance of the crystal:
CL = CXIN × CXOUT / (CXIN + CXOUT)
It is recommended to set the same value for capacitors the same
at each crystal pin, meaning:
CXIN = CXOUT
Example 1: The crystal load capacitance is specified as 8pF and
the stray capacitance at each crystal pin is Cs = 1.5pF. Assuming
equal capacitance value at XIN and XOUT, the equation is as
follows:
Cs1 and Cs2 are stray capacitances at each crystal pin and
typical values are between 1pF and 3pF.
8pF = (9pF + 0.5pF × XTAL[5:0] + 1.5pF) / 2
So, XTAL[5:0] = 11 (decimal).
Ce1 and Ce2 are additional external capacitors, increasing the
load capacitance reduces the oscillator gain so please consult the
factory when adding Ce1 and/or Ce2 to avoid crystal startup
issues. Ci1 and Ci2 are integrated programmable load capacitors,
one at XIN and one at XOUT. Ci1 and Ci2.
Example 2: The crystal load capacitance is specified as 12pF and
the stray capacitance Cs is unknown. Footprints for external
capacitors Ce are added and a worst case Cs of 5pF is used. For
now we use Cs + Ce = 5pF and the right value for Ce can be
determined later to make 5pF together with Cs.
The value of each capacitor is composed of a fixed capacitance
amount plus a variable capacitance amount set with the XTAL[5:0]
register.
12pF = (9pF + 0.5pF × XTAL[5:0] + 5pF) / 2
So, XTAL[5:0] = 20 (decimal).
Table 22. Recommended Crystal Characteristics
Parameter
Minimum
Mode of Oscillation
Typical
Maximum
Units
25
40
MHz
10
100
Ω
7
pF
12
pF
8
pF
100
μW
Fundamental
Frequency
8
Equivalent Series Resistance (ESR)
Shunt Capacitance
Load Capacitance (CL) at < = 25MHz
6
Load Capacitance (CL) > 25MHz to 40MHz
6
Maximum Crystal Drive Level
©2021 Renesas Electronics Corporation
17
8
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Programmable Loop Filter
When device is at hardware select mode outputs will be
automatically aligned at POR. The same synchronization reset is
also triggered when switching between configurations with the
SEL0/1 pins. This ensures that the outputs remain aligned in
every configuration.
The device PLL loop bandwidth range depends on the input
reference frequency (Fref).
Table 23. Loop Filter Settings
Input Reference
Frequency (MHz)
Loop Bandwidth
Minimum (kHz)
Loop Bandwidth
Maximum (kHz)
1
40
126
350
300
1000
When using software mode I2C to reprogram an output divider
during operation, alignment can be lost. Alignment can be
restored by manually triggering the reset through I2C.
The outputs are aligned on the falling edges of each output by
default. Rising edge alignment can also be achieved by utilizing
the programmable skew feature to delay the faster clock by 180
degrees. The programmable skew feature also allows for fine
tuning of the alignment.
Fractional Output Dividers (FOD)
The device has 4 fractional output dividers (FOD). Each of the
FODs are comprised of a 12-bit integer counter, and a 24-bit
fractional counter. The output divider can operate in integer divide
only mode for improved performance, or utilize the fractional
counters to generate a clock frequency accurate to 50ppb.
Programmable Skew
The device has the ability to skew outputs by quadrature values.
The skew on each output can be adjusted from 0 to 360 degrees.
Skew is adjusted in units equal to 1/32 of the VCO period. So, for
100MHz output and a 2800MHz VCO, you can select how many
11.161ps units you want added to your skew (resulting in units of
0.402 degrees). For example, 0, 0.402, 0.804, 1.206, 1.408, and
so on. The granularity of the skew adjustment is always
dependent on the VCO period and the output period.
FOD has the following features:
Individual Spread Spectrum Modulation
The output clock frequencies can be modulated to spread energy
across a broader range of frequencies, lowering system EMI.
Each divider has individual spread ability. Spread modulation
independent of output frequency, a triangle wave modulation
between 30 and 63kHz.
Output Drivers
Spread spectrum can be applied to any output clock, any clock
frequency, and any spread amount from ±0.25% to ±2.5%
center-spread and -0.5% to -5% down-spread.
▪ 2.5V or 3.3V voltage level for HCSL/LVPECL operation
▪ 1.8V, 2.5V or 3.3V voltage levels for CMOS/LVDS operation
▪ CMOS supports 4 operating modes:
The device output drivers support the following features
individually:
•
•
•
•
Bypass Mode
Bypass mode (divide by 1) to allow the output to behave as a
buffered copy from the input or another FOD.
Cascaded Mode
When a given output is configured to at CMOSD or CMOSX2, then
all previously described configuration and control apply equally to
both pins.
As shown in the block diagram, FODs can be cascaded for lower
output frequency.
For example, user currently has OUT1 running at 12.288MHz and
needs another 48kHz output. The user can cascade FOD2 by
taking input from OUT1, with a divide ratio of 256. In this way,
OUT 2 is running at 48kHz while in alignment with 12.288MHz on
OUT1.
▪ Independent output enable/disabled by register bits. When
disabled, an output can be either in a logic 1 state or Hi-Z.
The following options are used to disable outputs:
1. Output turned off by I 2C.
2. Output turned off by SD/OE pin.
Dividers Alignment
3. Output unused, which means is turned off regardless of OE pin
status.
Each output divider block has a synchronizing pulse to provide
startup alignment between outputs dividers. This allows alignment
of outputs for low skew performance.
©2021 Renesas Electronics Corporation
CMOSD: OUTx and OUTxB 180 degrees out of phase
CMOSX2: OUTx and OUTxB phase-aligned
CMOS1: only OUTx pin is on
CMOS2: only OUTxB pin is on
18
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
SD/OE Pin Function
I2C Operation
SD/OE pin can be programmed as following functions:
The device acts as a slave device on the I2C bus using one of the
two I2C addresses (0xD0 or 0xD4) to allow multiple devices to be
used in the system. The interface accepts byte-oriented block
write and block read operations.
1. OE output enable (low active).
2. OE output enable (high active).
3. Global shutdown (low active).
4. Global shutdown (high active).
Address bytes(2 bytes) specify the register address of the byte
position of the first register to write or read.
Output behavior when disabled is also programmable. User will
have the option to choose output driver behavior when it's off:
Data bytes (registers) are accessed in sequential order from the
lowest to the highest byte (most significant bit first).
1. OUTx pin high, OUTxB pin low. (Controlled by SD/OE pin).
Read and write block transfers can be stopped after any complete
byte transfer. During a write operation, data will not be moved into
the registers until the STOP bit is received, at which point, all data
received in the block write will be written simultaneously.
2. OUTx/OUTxB Hi-Z (Controlled by SD/OE pin).
3. OUTx pin high, OUTxB pin low. (Configured through I2C).
4. OUTx/OUTxB Hi-Z (Configured by I2C).
For full electrical I2C compliance, use external pull-up resistors for
SDATA and SCLK.
The user has the option to disable the output with either I2C or
SD/OE pin. Refer to VersaClock 6E Family Register Descriptions
and Programming Guide for details.
Figure 8. I2C R/W Sequence
©2021 Renesas Electronics Corporation
19
R31DS0062EU0601 July 6, 2021
A
B
C
1
R7
10K
C7
2
3
FB1
2
C1
10uF
7
SD/OE
SD/OE
SEL1/SDA
SEL0/SCL
CLKSEL
CLKIN
CLKINB
XOUT
XIN/REF
2
CLKIN
.1uF
1
2 CLKINB
C12
.1uF
8
9
1
C13
6
SDA
SCL
1
2
CLKSEL
CLKIN
CLKINB
3
4
6
U5
5P49V6965A
C5
.1uF
V1P8VC
C4
.1uF
C8
.1uF
C11
.1uF
C14
.1uF
VDDD
VDDA
5
C15
.1uF
1
R2
2.2
V1P8VC
V1P8VC
OUTR0
V1P8VC
OUTR1
OUTRB1
V1P8VC
OUTR2
OUTRB2
V1P8VC
OUTR3
OUTRB3
V1P8VC
OUTR4
OUTRB4
23
24
21
20
19
18
17
16
15
14
13
10
11
12
R6 1
OUT_0_SEL-I2C
R9
10K
PULL-UP FOR
V1P8VC
HARDWARE
CONFIGURATION
CONTROL
REMOVE FOR I2C
V1P8VCA
5
22
4
2
C2
1uF
V1P8VCA
C3
.1uF
pin# 5
following pins have
weak internal
pull down resistors:
6, 7, 8, 9 and 24
VDDO4
OUT4
OUT4B
VDDO3
OUT3
OUT3B
VDDO2
OUT2
OUT2B
VDDO1
OUT1
OUT1B
VDDO0
OUT0_SEL_I2CB
FOR LVDS, LVPECL USE
TERMINATION ON RIGHT BEFORE
AC COUPLING
NP
FG_X1
FG_X2
7
OUT_0_SEL-I2C
1
R10
1
R11
1
R12
R3
1
2
2
50
2
50
2
50
R5
49.9
1%
2
33
2
33
R4
49.9
1%
2
1
2
1
2
1
LVCMOS TERMINATION
R15 1
2 33
2.5V and 3.3V HCSL TERMINATION
1
R13
1
R14
2
100
3.3V LVPECL TERMINATION
LVDS TERMINATION
2 33
3
RECEIVER
U4
RECEIVER
U2
RECEIVER
U3
1
8
for
7
6
pins#: 22,23,21,18,15,10
5
4
Date:
3
Wednesday, November 30, 2016
2
Sheet
1
of
1
1
Layout notes:
1. Separate Xout and Xin Traces by 3 x the trace width
2. Do not share crystal load capacitor ground via with
other components.
3. Route power from bead through bulk capacitor pad
then through 0.1uF capacitor pad then to clock chip
NOTE:FERRITE BEAD FB1 =
Vdd pad.
Manufacture Part Number
Z@100MHz PkgSz DC res. Current(Ma) 4. Do not share ground vias. One ground pin one ground
Fair-Rite
2504021217Y0
120
0402
0.5
200
via.
muRata
BLM15AG221SN1 220
0402
0.35
300
muRata
BLM15BB121SN1 120
0402
0.35
300
Integrated Device Technology
TDK
MMZ1005S241A
240
0402
0.18
200
San Jose, CA
TECSTAR
TB4532153121
120
0402
0.3
300
Size
Document Number
Rev
Revision history
A
5P49V6965_SCH
0.1
0.1 11/30/16 first publication
SIGNAL_BEAD
1
VCC1P8
PLACE NEAR
I2C CONTROLLER
IF USED
SDA
SCL
R8
10K
V3P3
C6
NP
GND
25.000 MHz
CL = 8pF
GND
2
1
D
4
Y1
2
1
2
1
1
2
2
1
1
2
1
2
1
2
1
2
1
2
1
2
2
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
EPAD
25
26
27
28
29
30
31
32
33
1
2
1
2
1
20
2
2
1
©2021 Renesas Electronics Corporation
1
8
A
B
C
D
5P49V6965 Datasheet
Typical Application Circuits
Figure 9. Application Circuit Example
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Input – Driving the XIN/REF or CLKIN
Driving XIN/REF with a CMOS Driver
In some cases, it is encouraged to have XIN/REF driven by a clock input for reasons like better SNR, multiple input select with device
CLKIN, etc. The XIN/REF pin is able to take an input when its amplitude is between 500mV and 1.2V and the slew rate more than
0.2V/ns.
The XIN/REF input can be overdriven by an LVCMOS driver or by one side of a differential driver through an AC coupling capacitor. The
XOUT pin can be left floating.
Figure 10. Overdriving XIN with a CMOS Driver
XOUT
VDD
Ro
Rs
Zo = 50 Ohm
C3
R1
V_XIN
XIN / REF
Ro + Rs = 50 ohm
1 nF
LVCMOS
R2
Table 24. Nominal Voltage Divider Values for Overdriving XIN with Single-ended Driver
LVCMOS Diver VDD
Ro + Rs
R1
R2
V_XIN (peak)
Ro+Rs+R1+R2
3.3
50.0
130
75
0.97
255
2.5
50.0
100
100
1.00
250
1.8
50.0
62
130
0.97
242
Driving XIN with an LVPECL Driver
Figure 11 shows an example of the interface diagram for a +3.3V LVPECL driver. This is a standard LVPECL termination with one side of
the driver feeding the XIN/REF input. It is recommended that all components in the schematics be placed in the layout; though some
components might not be used, they can be utilized for debugging purposes. The datasheet specifications are characterized and
guaranteed by using a quartz crystal as the input. If the driver is 2.5V LVPECL, the only change necessary is to use the appropriate value
of R3.
Figure 11. Overdriving XIN with an LVPECL Driver
XOUT
Zo = 50 Ohm
C1
Zo = 50 Ohm
1 nF
XIN / REF
+3.3V LVPECL Driv er
R1
50
R2
50
R3
50
©2021 Renesas Electronics Corporation
21
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Wiring the CLKIN Pin to Accept Single-ended Inputs
CLKIN cannot take a signal larger than 1.2V pk-pk due to the 1.2V regulated input inside. However, it is internally AC coupled so it is able
to accept both LVDS and LVPECL input signals.
Occasionally, it is desired to have CLKIN to take CMOS levels. Below is an example showing how this can be achieved.
This configuration has three properties:
1. Total output impedance of Ro and Rs matches the 50Ω transmission line impedance.
2. Vrx voltage is generated at the CLKIN which maintains the LVCMOS driver voltage level across the transmission line for best S/N.
3. R1–R2 voltage divider values ensure that Vrx p-p at CLKIN is less than the maximum value of 1.2V.
Figure 12. Recommended Schematic for Driving CLKIN with LVCMOS Driver
VDD
Ro
Rs
Zo = 50 Ohm
R1
Vrx
CLKI N
Ro + Rs = 5 0
LVCMOS
CLKI NB
R2
VersaCloc k6 5Receiver
Rec eiver
VersaClock
Table 25 shows resistor values that ensure the maximum drive level for the CLKIN port is not exceeded for all combinations of 5%
tolerance on the driver VDD, VDDO0 and 5% resistor tolerances. The values of the resistors can be adjusted to reduce the loading for
slower and weaker LVCMOS driver by increasing the impedance of the R1–R2 divider. To better assist this assessment, the total load
(Ro + Rs + R1 + R2) on the driver is included in the table.
Table 25. Nominal Voltage Divider Values for Overdriving CLKIN with Single-ended Driver
LVCMOS Diver VDD
Ro + Rs
R1
R2
Vrx (peak)
Ro+Rs+R1+R2
3.3
50.0
130
75
0.97
255
2.5
50.0
100
100
1.00
250
1.8
50.0
62
130
0.97
242
Driving CLKIN with Differential Clock
CLKIN/CLKINB will accept DC coupled HCSL/LVPECL/LVDS signals.
Figure 13. CLKIN, CLKINB Input Driven by an HCSL Driver
Q
nQ
Zo=50ohm
CLKIN
Zo=50ohm
CLKINB
VersaClock 6 Receiver
©2021 Renesas Electronics Corporation
22
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Output – Single-ended or Differential Clock Terminations
LVDS Termination
For a general LVDS interface, the recommended value for the termination impedance (ZT) is between 90Ω and 132Ω. The actual value
should be selected to match the differential impedance (Zo) of your transmission line. A typical point-to-point LVDS design uses a 100Ω
parallel resistor at the receiver and a 100Ω. differential transmission-line environment. In order to avoid any transmission-line reflection
issues, the components should be surface mounted and must be placed as close to the receiver as possible. The standard termination
schematic as shown in figure Standard Termination or the termination of figure Optional Termination can be used, which uses a center tap
capacitance to help filter common mode noise. The capacitor value should be approximately 50pF. In addition, since these outputs are
LVDS compatible, the input receiver's amplitude and common-mode input range should be verified for compatibility with the Renesas
LVDS output. If using a non-standard termination, it is recommended to contact Renesas and confirm that the termination will function as
intended. For example, the LVDS outputs cannot be AC coupled by placing capacitors between the LVDS outputs and the 100Ω shunt
load. If AC coupling is required, the coupling caps must be placed between the 100Ω shunt termination and the receiver. In this manner,
the termination of the LVDS output remains DC coupled. If using a non-standard termination, it is recommended to contact Renesas and
confirm that the termination will function as intended.
Figure 14. Standard and Optional Terminations
Standard Termination
LVDS
Driver
Z O ZT
ZT
LVDS
Receiver
Optional Termination
LVDS
Driver
ZT
2
Z O ZT
©2021 Renesas Electronics Corporation
C
23
ZT
2
LVDS
Receiver
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
LVPECL Termination
The clock layout topology shown below is a typical termination for LVPECL outputs.
The differential outputs generate ECL/LVPECL compatible outputs. Therefore, terminating resistors (DC current path to ground) or
current sources must be used for functionality. These outputs are designed to drive 50Ω transmission lines. Matched impedance
techniques should be used to maximize operating frequency and minimize signal distortion.
For VDDO = 2.5V, the VDDO - 2V is very close to ground level. The R3 in 2.5V LVPECL output termination can be eliminated and the
termination is shown in Figure 17, 2.5V LVPECL Output Termination.
Figure 15. 3.3V LVPECL Output Termination (1)
Figure 17. 2.5V LVPECL Output Termination
2.5V
3.3V
3.3V
VDDO = 2.5V
Zo = 50 Ohm
+
R1
250 Ohm
Zo = 50 Ohm
+
Zo = 50 Ohm
LVPECL
R1
50 Ohm
Zo = 50 Ohm
Input
R2
50 Ohm
2.5V LVPECL
Driver
RTT
50 Ohm
Figure 16. 3.3V LVPECL Output Termination (2)
R3
125 Ohm
-
R2
62.5 Ohm
R4
62.5 Ohm
Figure 18. 2.5V LVPECL Driver Termination (1)
3.3V
3.3V
VDDO = 2.5V
2.5V
3.3V
R4
125 Ohm
Zo = 50 Ohm
+
Zo = 50 Ohm
+
Zo = 50 Ohm
LVPECL
Zo = 50 Ohm
-
2.5V LVPECL
Driver
Input
R1
84 Ohm
2.5V
R3
250 Ohm
R2
84 Ohm
-
R1
50 Ohm
R2
50 Ohm
Figure 19. 2.5V LVPECL Driver Termination (2)
VDDO = 2.5V
2.5V
Zo = 50 Ohm
+
Zo = 50 Ohm
2.5V LVPECL
Driver
-
R1
50 Ohm
R2
50 Ohm
R3
18 Ohm
©2021 Renesas Electronics Corporation
24
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
HCSL Termination
HCSL termination scheme applies to both 3.3V and 2.5V V DDO.
Figure 20. HCSL Receiver Terminated
33 Ohm
VersaClock 6E Output
Driver
33 Ohm
Zo = 50 Ohm
+
Receiver
Zo = 50 Ohm
-
HCSL
50 Ohm
50 Ohm
Figure 21. HCSL Source Terminated
Zo = 50 Ohm
33 Ohm
VersaClock 6E Output
Driver
+
Receiver
Zo = 50 Ohm
33 Ohm
-
HCSL
50 Ohm
50 Ohm
LVCMOS Termination
Each output pair can be configured as a standalone CMOS or dual-CMOS output driver. CMOSD driver termination example is shown
below.
CMOS1 - Single CMOS active on OUTx pin.
CMOS2 - Single CMOS active on OUTxB pin.
CMOSD - Dual CMOS outputs active on both OUTx and OUTxB pins, 180 degrees out of phase.
CMOSX2 - Dual CMOS outputs active on both OUTx and OUTxB pins, in-phase.
Figure 22. LVCMOS Termination
33 Ohm
VersaClock 6E Output
Driver
Zo = 50 Ohm
+
Receiver
33 Ohm
Zo = 50 Ohm
-
CMOSD
©2021 Renesas Electronics Corporation
25
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Package Outline Drawings
The package outline drawings are located at the end of this document and are accessible from the Renesas website (see Ordering
Information for POD links). The package information is the most current data available and is subject to change without revision of this
document.
Marking Diagram
6965A
ddd
YWW**$
▪ Line 1: truncated part number.
▪ Line 2: “ddd” denotes dash code.
▪ Line 3:
• “YWW” is the last digit of the year and week that the part was assembled.
• “**” denotes sequential lot number.
• “$” denotes mark code.
Ordering Information
1
2
Orderable Part Number
Package
Carrier Type
Temperature
5P49V6965AdddNLGI
4 × 4 mm, 0.5mm pitch 24-VFQFPN
Tray
-40° to +85°C
5P49V6965AdddNLGI8
4 × 4 mm, 0.5mm pitch 24-VFQFPN
Tape and Reel
-40° to +85°C
5P49V6965A000NLGI
4 × 4 mm, 0.5mm pitch 24-VFQFPN
Tray
-40° to +85°C
5P49V6965A000NLGI8
4 × 4 mm, 0.5mm pitch 24-VFQFPN
Tape and Reel
-40° to +85°C
“ddd” denotes factory programmed configurations based on required settings. Contact factory for factory programming.
“000” denotes un-programmed parts for user customization.
©2021 Renesas Electronics Corporation
26
R31DS0062EU0601 July 6, 2021
5P49V6965 Datasheet
Revision History
Revision Date
Description of Change
July 6, 2021
▪ Updated “non-standard termination” descriptive text in section LVDS Termination.
▪ Updated Package Outline Drawings section.
August 20, 2020
Updated the slew rate terminology in section Driving XIN/REF with a CMOS Driver.
September 18, 2019
▪ Updated Absolute Maximum Ratings table.
▪ Updated PCI Express Jitter Performance tables (Table 17 and Table 18).
▪ Updated Electrical Characteristics tables (Table 9, Table 11, and Table 14).
June 19, 2019
▪
▪
▪
▪
▪
August 31, 2018
Updated schematics for Driving XIN/REF with a CMOS Driver and Driving XIN with an LVPECL Driver.
March 15, 2018
▪ Updated absolute maximum ratings for supply voltage to 3.6V.
▪ Updated typical and maximum values in Current Consumption table.
▪ Minor updates to AC Timing Characteristics, Electrical Characteristics – CMOS Outputs, and Electrical
PCIe specification updated.
Added recommended power ramp time.
Expanded spread spectrum value range.
I2C tolerant voltage footnote changed to 3.3V.
LVDS Termination section allows AC-coupling for LVDS signals.
Characteristics – LVDS Outputs tables.
November 6, 2017
Initial release.
©2021 Renesas Electronics Corporation
27
R31DS0062EU0601 July 6, 2021
24-VFQFPN, Package Outline Drawing
4.0 x 4.0 x 0.90 mm Body,0.50mm Pitch,Epad 2.80 x 2.80 mm
NLG24P2, PSC-4192-02, Rev 02, Page 1
© Integrated Device Technology, Inc.
24-VFQFPN, Package Outline Drawing
4.0 x 4.0 x 0.90 mm Body,0.50mm Pitch,Epad 2.80 x 2.80 mm
NLG24P2, PSC-4192-02, Rev 02, Page 2
Package Revision History
© Integrated Device Technology, Inc.
Description
Date Created
Rev No.
Nov 2, 2018
Rev 02
New Format, Recalculate Land Pattern
Oct 12, 2016
Rev 01
Add Chamfer
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.