71V2546S
128K x 36
3.3V Synchronous ZBT™ SRAM
2.5V I/O, Burst Counter
Pipelined Outputs
Features
◆
◆
◆
◆
◆
◆
◆
128K x 36 memory configurations
Supports high performance system speed - 150 MHz
(3.8 ns Clock-to-Data Access)
ZBTTM Feature - No dead cycles between write and read
cycles
Internally synchronized output buffer enable eliminates the
need to control OE
Single R/W (READ/WRITE) control pin
Positive clock-edge triggered address, data, and control
signal registers for fully pipelined applications
◆
◆
◆
◆
◆
◆
4-word burst capability (interleaved or linear)
Individual byte write (BW1 - BW4) control (May tie active)
Three chip enables for simple depth expansion
3.3V power supply (±5%), 2.5V I/O Supply (VDDQ)
Packaged in a JEDEC standard 100-pin plastic thin quad
flatpack (TQFP) and 119 ball grid array (BGA)
Industrial temperature range (–40°C to +85°C) is available
for selected speeds
Green parts available, see ordering information
Functional Block Diagram
LBO
Address A [0:16]
128Kx36 BIT
MEMORY ARRAY
D
Q
Address
D
Q
Control
CE1, CE, CE2
R/W
Input Register
CEN
ADV/LD
BWx
D
DI
DO
Control Logic
Q
Clk
Mux
Sel
D
Clk
Clock
Output Register
Q
Gate
OE
5294 drw 01a
Data I/O [0:31],
I/O P[1:4]
ZBT and ZeroBus Turnaround are trademarks of Renesas and the architecture is supported by Micron Technology and Motorola Inc.
1
Aug.12.20
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Description
Commercial and Industrial Temperature Ranges
The IDT71V2546 is a 3.3V high-speed 4,718,592-bit (4.5 Megabit)
synchronous SRAM. It is designed to eliminate dead bus cycles when
turning the bus around between reads and writes, or writes and reads.
Thus, they have been given the name ZBTTM, or Zero Bus Turnaround.
Address and control signals are applied to the SRAM during one clock
cycle, and two cycles later the associated data cycle occurs, be it read
or write.
The IDT71V2546 contains data I/O, address and control signal
registers. Output enable is the only asynchronous signal and can be used
to disable the outputs at any given time.
A Clock Enable (CEN) pin allows operation of the IDT71V2546 to be
suspended as long as necessary. All synchronous inputs are ignored
when (CEN) is high and the internal device registers will hold their previous
values.
There are three chip enable pins (CE1, CE2, CE2) that allow the user
to deselect the device when desired. If any one of these three are not
asserted when ADV/LD is low, no new memory operation can be initiated.
However, any pending data transfers (reads or writes) will be completed.
The data bus will tri-state two cycles after chip is deselected or a write is
initiated.
The IDT71V2546 has an on-chip burst counter. In the burst mode, the
IDT71V2546 can provide four cycles of data for a single address
presented to the SRAM. The order of the burst sequence is defined by the
LBO input pin. The LBO pin selects between linear and interleaved burst
sequence. The ADV/LD signal is used to load a new external address
(ADV/LD = LOW) or increment the internal burst counter (ADV/LD =
HIGH).
The IDT71V2546 SRAM utilizes a high-performance CMOS process
and is packaged in a JEDEC standard 14mm x 20mm 100-pin thin plastic
quad flatpack (TQFP) as well as a 119 ball grid array (BGA).
Pin Description Summary
A0-A16
Ad d re ss Inp uts
Inp ut
Synchro no us
CE1, CE2, CE2
Chip Enab le s
Inp ut
Synchro no us
OE
Outp ut Enab le
Inp ut
Asynchro no us
R/W
Re ad /Write Sig nal
Inp ut
Synchro no us
CEN
Clo ck Enab le
Inp ut
Synchro no us
BW1, BW2, BW3, BW4
Ind ivid ual Byte Write Se le cts
Inp ut
Synchro no us
CLK
Clo ck
Inp ut
N/A
ADV/LD
Ad vance b urst ad d re ss / Lo ad ne w ad d re ss
Inp ut
Synchro no us
LBO
Line ar / Inte rle ave d Burst Ord e r
Inp ut
Static
ZZ
S le e p Mo d e
Inp ut
Synchro no us
I/O0-I/O31, I/OP1-I/OP4
Data Inp ut / Outp ut
I/O
Synchro no us
VDD, VDDQ
Co re Po we r, I/O Po we r
Sup p ly
Static
VSS
Gro und
Sup p ly
Static
5294 tb l 01
6.42
2
Aug.12.20
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Pin Definitions(1)
Symbol
Pin Function
I/O
Active
Description
A0-A16
Ad d re ss Inp uts
I
N/A
Synchro no us Ad d re ss inp uts. The ad d re ss re g iste r is trig g e re d b y a co mb inatio n o f the rising e d g e o f CLK,
ADV/LD lo w, CEN lo w, and true chip e nab le s.
ADV/LD
Ad vance / Lo ad
I
N/A
ADV/LD is a synchro no us inp ut that is use d to lo ad the inte rnal re g iste rs with ne w ad d re ss and co ntro l whe n it
is samp le d lo w at the rising e d g e o f clo ck with the chip se le cte d . Whe n ADV/LD is lo w with the chip
d e se le cte d , any b urst in p ro g re ss is te rminate d . Whe n ADV/LD is samp le d hig h the n the inte rnal b urst co unte r
is ad vance d fo r any b urst that was in p ro g re ss. The e xte rnal ad d re sse s are ig no re d whe n ADV/LD is samp le d
hig h.
R/W
Re ad / Write
I
N/A
R/W sig nal is a synchro no us inp ut that id e ntifie s whe the r the curre nt lo ad cycle initiate d is a Re ad o r Write
acce ss to the me mo ry array. The d ata b us activity fo r the curre nt cycle take s p lace two clo ck cycle s late r.
CEN
Clo ck Enab le
I
LOW
Synchro no us Clo ck Enab le Inp ut. Whe n CEN is samp le d hig h, all o the r synchro no us inp uts, includ ing clo ck
are ig no re d and o utp uts re main unchang e d . The e ffe ct o f CEN samp le d hig h o n the d e vice o utp uts is as if the
lo w to hig h clo ck transitio n d id no t o ccur. Fo r no rmal o p e ratio n, CEN must b e samp le d lo w at rising e d g e o f
c lo c k .
BW1-BW4
Ind ivid ual Byte
Write Enab le s
I
LOW
Synchro no us b yte write e nab le s. Each 9-b it b yte has its o wn active lo w b yte write e nab le . On lo ad write cycle s
(Whe n R/W and ADV/LD are samp le d lo w) the ap p ro p riate b yte write sig nal (BW1-BW4) must b e valid . The
b yte write sig nal must also b e valid o n e ach cycle o f a b urst write . Byte Write sig nals are ig no re d whe n R/W is
samp le d hig h. The ap p ro p riate b yte (s) o f d ata are writte n into the d e vice two cycle s late r. BW1-BW4 can all b e
tie d lo w if always d o ing write to the e ntire 36-b it wo rd .
CE1, CE2
Chip Enab le s
I
LOW
Synchro no us active lo w chip e nab le . CE1 and CE2 are use d with CE2 to e nab le the IDT71V2546. (CE1 o r CE2
samp le d hig h o r CE2 samp le d lo w) and ADV/LD lo w at the rising e d g e o f clo ck, initiate s a d e se le ct cycle . The
ZBTTM has a two cycle d e se le ct, i.e ., the d ata b us will tri-state two clo ck cycle s afte r d e se le ct is initiate d .
CE2
Chip Enab le
I
HIGH
Synchro no us active hig h chip e nab le . CE2 is use d with CE1 and CE2 to e nab le the chip . CE2 has inve rte d
p o larity b ut o the rwise id e ntical to CE1 and CE2.
CLK
Clo ck
I
N/A
This is the clo ck inp ut to the IDT71V2546. Exce p t fo r OE, all timing re fe re nce s fo r the d e vice are mad e with
re sp e ct to the rising e d g e o f CLK.
I/O0-I/O31
I/OP1-I/OP4
Data Inp ut/Outp ut
I/O
N/A
Synchro no us d ata inp ut/o utp ut (I/O) p ins. Bo th the d ata inp ut p ath and d ata o utp ut p ath are re g iste re d and
trig g e re d b y the rising e d g e o f CLK.
LBO
Line ar Burst Ord e r
I
LOW
Burst o rd e r se le ctio n inp ut. Whe n LBO is hig h the Inte rle ave d b urst se q ue nce is se le cte d . Whe n LBO is lo w
the Line ar b urst se q ue nce is se le cte d . LBO is a static inp ut and it must no t chang e d uring d e vice o p e ratio n.
OE
Outp ut Enab le
I
LOW
Asynchro no us o utp ut e nab le . OE must b e lo w to re ad d ata fro m the IDT71V2546. Whe n OE is hig h the I/O p ins
are in a hig h-imp e d ance state . OE d o e s no t ne e d to b e active ly co ntro lle d fo r re ad and write cycle s. In no rmal
o p e ratio n, OE can b e tie d lo w.
ZZ
S le e p Mo d e
I
HIGH
Synchro no us sle e p mo d e inp ut. ZZ HIGH will g ate the CLK inte rnally and p o we r d o wn the IDT71V2546 to its
lo we st p o we r co nsump tio n le ve l. Data re te ntio n is g uarante e d in Sle e p Mo d e . This p in has an inte rnal
p ulld o wn.
VDD
Po we r Sup p ly
N/A
N/A
3.3V co re p o we r sup p ly.
VDDQ
Po we r Sup p ly
N/A
N/A
2.5V I/O Sup p ly.
VSS
Gro und
N/A
N/A
Gro und .
5294 tb l 02
NOTE:
1. All synchronous inputs must meet specified setup and hold times with respect to CLK.
6.42
3
Aug.12.20
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
CE2
BW4
BW3
BW2
BW1
CE2
VDD
VSS
CLK
R/W
CEN
OE
ADV/LD
NC
NC
A8
A9
A6
A7
CE1
Pin Configuration(3) — 128K x 36, PKG100
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81
I/OP3
I/O16
I/O17
VDDQ
VSS
I/O18
I/O19
I/O20
I/O21
VSS
VDDQ
I/O22
I/O23
VDD(1)
VDD
VDD(1)
VSS
I/O24
I/O25
VDDQ
VSS
I/O26
I/O27
I/O28
I/O29
VSS
VDDQ
I/O30
I/O31
I/OP4
1
80
2
79
3
78
77
4
5
6
76
75
7
74
8
73
9
72
71
10
11
12
13
71V2546
PKG100
70
69
68
14
67
15
66
16
65
17
64
18
19
63
62
20
61
21
60
22
59
23
24
58
57
25
56
26
55
27
28
54
53
29
52
30
51
I/OP2
I/O15
I/O14
VDDQ
VSS
I/O13
I/O12
I/O11
I/O10
VSS
VDDQ
I/O9
I/O8
VSS
VDD(1)
VDD
VSS/ZZ(2)
I/O7
I/O6
VDDQ
VSS
I/O5
I/O4
I/O3
I/O2
VSS
VDDQ
I/O1
I/O0
I/OP1
31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
,
LBO
A5
A4
A3
A2
A1
A0
NC
NC
VSS
VDD
NC
NC
A10
A11
A12
A13
A14
A15
A16
5294 drw 02
Top View
100 TQFP
NOTES:
1. Pins 14, 16 and 66 do not have to be connected directly to VDD as long as the input voltage is ≥ VIH.
2. Pin 64 does not have to be connected directly to VSS as long as the input voltage is ≤ VIL; on the latest die revision this pin supports ZZ (sleep mode).
3, This text does not indicate the orientation of actual part-marking..
6.42
4
Aug.12.20
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Pin Configuration(3) — 128K x 36, BG119
1
2
3
4
5
6
7
A
VDDQ
A6
A4
NC
A8
A16
VDDQ
B
NC
CE 2
A3
A9
CE2
NC
C
NC
A7
A2
VDD
A12
A15
NC
D
I/O16
I/OP3
VSS
NC
VSS
I/OP2
I/O15
E
I/O17
I/O18
VSS
CE1
VSS
I/O13
I/O14
F
VDDQ
I/O19
VSS
OE
VSS
I/O12
VDDQ
G
I/O20
I/O21
BW3
NC
BW2
I/O11
I/O10
H
I/O22
I/O23
VSS
R/W
VSS
I/O9
I/O8
J
VDDQ
VDD
VDD(1)
VDD
VDD(1)
VDD
VDDQ
K
I/O24
I/O26
VSS
CLK
VSS
I/O6
I/O7
L
I/O25
I/O27
BW4
NC
BW1
I/O4
I/O5
M
VDDQ
I/O28
VSS
CEN
VSS
I/O3
VDDQ
N
I/O29
I/O30
VSS
A1
VSS
I/O2
I/O1
P
I/O31
I/OP4
VSS
A0
VSS
I/OP1
I/O0
R
NC
A5
LBO
VDD
A13
NC
T
NC
NC
A10
A11
A14
NC
NC/ZZ(2)
U
VDDQ
NC
NC
NC
NC
NC
ADV/LD
VDD(1)
VDDQ
5294 drw 13a
Top View
119 BGA
NOTES:
1. J3, J5, and R5 do not have to be directly connected to VDD as long as the input voltage is ≥ VIH.
2. Pin T7 supports ZZ (sleep mode) on the latest die revision.
3. This text does not indicate orientation of actual part-marking.
6.42
5
Aug.12.20
,
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Recommended DC Operating
Conditions
Recommended Operating
Temperature and Supply Voltage
Grade
Temperature(1)
VSS
VDD
VDDQ
Co mme rcial
0° C to +70° C
0V
3.3V± 5%
2.5V± 5%
Ind ustrial
-40° C to +85° C
0V
3.3V± 5%
2.5V± 5%
Min.
Typ.
Max.
Unit
VDD
Co re Sup p ly Vo ltag e
3.135
3.3
3.465
V
VDDQ
I/O Sup p ly Vo ltag e
2.375
2.5
2.625
V
VSS
Sup p ly Vo ltag e
0
0
0
V
1.7
____
VDD +0.3
1.7
____
-0.3(1)
____
VIH
Absolute Maximum Ratings
Rating
Parameter
5294 tb l 05
NOTE:
1. TA is the "instant on" case temperature.
Symbol
Symbol
(1)
Commercial &
Industrial Values
Unit
VTERM(2)
Te rminal Vo ltag e with
Re sp e ct to GND
-0.5 to +4.6
V
VTERM(3,6)
Te rminal Vo ltag e with
Re sp e ct to GND
-0.5 to VDD
V
VTERM(4,6)
Te rminal Vo ltag e with
Re sp e ct to GND
-0.5 to VDD +0.5
V
VTERM(5,6)
Te rminal Vo ltag e with
Re sp e ct to GND
-0.5 to VDDQ +0.5
V
Inp ut Hig h Vo ltag e - Inp uts
VIH
Inp ut Hig h Vo ltag e - I/O
VIL
Inp ut Lo w Vo ltag e
V
(2)
VDDQ +0.3
0.7
V
V
NOTES:
1. VIL (min.) = –1.0V for pulse width less than tCYC/2, once per cycle.
2. VIH (max.) = +6.0V for pulse width less than tCYC/2, once per cycle.
5294 tb l 03
100 TQFP Capacitance(1)
(TA = +25° C, f = 1.0MHz)
Symbol
Parameter(1)
CIN
Inp ut Cap acitance
CI/O
I/O Cap acitance
Conditions
Max.
Unit
VIN = 3d V
5
pF
VOUT = 3d V
7
pF
5294 tb l 07
Commercial
Op e rating Te mp e rature
-0 to +70
o
C
Industrial
Op e rating Te mp e rature
-40 to +85
o
C
NOTE:
1. This parameter is guaranteed by device characterization, but not production
tested.
TA(7)
TBIAS
Te mp e rature
Und e r Bias
-55 to +125
o
C
TSTG
Sto rag e
Te mp e rature
-55 to +125
o
C
119 BGA Capacitance(1)
(TA = +25° C, f = 1.0MHz)
Symbol
Parameter(1)
PT
Po we r Dissip atio n
2.0
W
CIN
Inp ut Cap acitance
IOUT
DC Outp ut Curre nt
50
mA
CI/O
I/O Cap acitance
5294 tb l 06
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated
in the operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
2. VDD terminals only.
3. VDDQ terminals only.
4. Input terminals only.
5. I/O terminals only.
6. This is a steady-state DC parameter that applies after the power supply has
reached its nominal operating value. Power sequencing is not necessary;
however, the voltage on any input or I/O pin cannot exceed VDDQ during power
supply ramp up.
7. TA is the "instant on" case temperature.
Max.
Unit
VIN = 3d V
7
pF
VOUT = 3d V
7
pF
5294 tb l 07a
NOTE:
1. This parameter is guaranteed by device characterization, but not production
tested.
6.42
6
Aug.12.20
Conditions
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Synchronous Truth Table(1)
CEN
R/W
Chip(5)
Enable
ADV/LD
BWx
ADDRESS
USED
PREVIOUS CYCLE
CURRENT CYCLE
I/O(6)
(2 cycles later)
L
L
S e le c t
L
Valid
Exte rnal
X
LOAD WRITE
D(7)
L
H
S e le c t
L
X
Exte rnal
X
LOAD READ
Q(7)
L
X
X
H
Valid
Inte rnal
LOAD WRITE /
BURST WRITE
BURST WRITE
(Ad vance b urst co unte r)(2)
D(7)
L
X
X
H
X
Inte rnal
LOAD READ /
BURST READ
BURST READ
(Ad vance b urst co unte r)(2)
Q(7)
L
X
De se le ct
L
X
X
X
DESELECT o r STOP(3)
HiZ
L
X
X
H
X
X
DESELECT / NOOP
NOOP
HiZ
H
X
X
X
X
X
X
SUSPEND(4)
Pre vio us Value
5294 tb l 08
NOTES:
1. L = VIL, H = VIH, X = Don’t Care.
2. When ADV/LD signal is sampled high, the internal burst counter is incremented. The R/W signal is ignored when the counter is advanced. Therefore the nature of
the burst cycle (Read or Write) is determined by the status of the R/W signal when the first address is loaded at the beginning of the burst cycle.
3. Deselect cycle is initiated when either (CE1, or CE2 is sampled high or CE2 is sampled low) and ADV/LD is sampled low at rising edge of clock. The data bus will
tri-state two cycles after deselect is initiated.
4. When CEN is sampled high at the rising edge of clock, that clock edge is blocked from propagating through the part. The state of all the internal registers and the I/
Os remains unchanged.
5. To select the chip requires CE1 = L, CE2 = L, CE2 = H on these chip enables. Chip is deselected if any one of the chip enables is false.
6. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up.
7. Q - Data read from the device, D - data written to the device.
Partial Truth Table for Writes(1)
R/W
BW1
BW2
BW3
BW4
READ
H
X
X
X
X
WRITE ALL BYTES
L
L
L
L
L
L
L
H
H
H
OPERATION
WRITE BYTE 1 (I/O[0:7], I/OP1)(2)
(2)
WRITE BYTE 2 (I/O[8:15], I/OP2)
L
H
L
H
H
(2)
WRITE BYTE 3 (I/O[16:23], I/OP3)
L
H
H
L
H
WRITE BYTE 4 (I/O[24:31], I/OP4)(2)
L
H
H
H
L
NO WRITE
L
H
H
H
H
5294 tb l 09
NOTES:
1. L = VIL, H = VIH, X = Don’t Care.
2. Multiple bytes may be selected during the same cycle.
6.42
7
Aug.12.20
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Interleaved Burst Sequence Table (LBO=VDD)
Sequence 1
Sequence 2
Sequence 3
Sequence 4
A1
A0
A1
A0
A1
A0
A1
A0
First Ad d re ss
0
0
0
1
1
0
1
1
Se co nd Ad d re ss
0
1
0
0
1
1
1
0
Third Ad d re ss
1
0
1
1
0
0
0
1
Fo urth Ad d re ss(1)
1
1
1
0
0
1
0
0
5294 tb l 10
NOTE:
1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting.
Linear Burst Sequence Table (LBO=VSS)
Sequence 1
Sequence 2
Sequence 3
Sequence 4
A1
A0
A1
A0
A1
A0
A1
A0
First Ad d re ss
0
0
0
1
1
0
1
1
Se co nd Ad d re ss
0
1
1
0
1
1
0
0
Third Ad d re ss
1
0
1
1
0
0
0
1
Fo urth Ad d re ss(1)
1
1
0
0
0
1
1
0
5294 tb l 11
NOTE:
1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting.
Functional Timing Diagram(1)
CYCLE
n+29
n+30
n+31
n+32
n+33
n+34
n+35
n+36
n+37
A29
A30
A31
A32
A33
A34
A35
A36
A37
C29
C30
C31
C32
C33
C34
C35
C36
C37
D/Q27
D/Q28
D/Q29
D/Q30
D/Q31
D/Q32
D/Q33
D/Q34
D/Q35
CLOCK
(2)
ADDRESS
(A0 - A16)
(2)
CONTROL
(R/W , ADV/LD , BW x)
(2)
DATA
I/O [0:31], I/O P[1:4]
,
5294 drw 03
NOTES:
1. This assumes CEN, CE1, CE2, CE2 are all true.
2. All Address, Control and Data_In are only required to meet set-up and hold time with respect to the rising edge of clock. Data_Out is valid after a clock-to-data
delay from the rising edge of clock.
6.42
8
Aug.12.20
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Device Operation - Showing Mixed Load, Burst,
Deselect and NOOP Cycles(2)
Cycle
Address
R/W
ADV/LD
CE(1)
CEN
BWx
OE
I/O
Comments
n
A0
H
L
L
L
X
X
X
Lo ad re ad
n+1
X
X
H
X
L
X
X
X
Burst re ad
n+2
A1
H
L
L
L
X
L
Q0
Lo ad re ad
n+3
X
X
L
H
L
X
L
Q0+1
n+4
X
X
H
X
L
X
L
Q1
NOOP
n+5
A2
H
L
L
L
X
X
Z
Lo ad re ad
n+6
X
X
H
X
L
X
X
Z
Burst re ad
n+7
X
X
L
H
L
X
L
Q2
De se le ct o r STOP
n+8
A3
L
L
L
L
L
L
Q2+1
Lo ad write
n+9
X
X
H
X
L
L
X
Z
Burst write
n+10
A4
L
L
L
L
L
X
D3
Lo ad write
n+11
X
X
L
H
L
X
X
D3+1
n+12
X
X
H
X
L
X
X
D4
NOOP
n+13
A5
L
L
L
L
L
X
Z
Lo ad write
n+14
A6
H
L
L
L
X
X
Z
Lo ad re ad
n+15
A7
L
L
L
L
L
X
D5
Lo ad write
n+16
X
X
H
X
L
L
L
Q6
Burst write
n+17
A8
H
L
L
L
X
X
D7
Lo ad re ad
n+18
X
X
H
X
L
X
X
D7+1
Burst re ad
n+19
A9
L
L
L
L
L
L
Q8
Lo ad write
De se le ct o r STOP
De se le ct o r STOP
5294 tb l 12
NOTES:
1. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
2. H = High; L = Low; X = Don’t Care; Z = High Impedance.
Read Operation(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O
Comments
n
A0
H
L
L
L
X
X
X
Ad d re ss and Co ntro l me e t se tup
n+1
X
X
X
X
L
X
X
X
Clo ck Se tup Valid
n+2
X
X
X
X
X
X
L
Q0
Co nte nts o f Ad d re ss A0 Re ad Out
NOTES:
1. H = High; L = Low; X = Don’t Care; Z = High Impedance.
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
6.42
9
Aug.12.20
5294 tb l 13
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Burst Read Operation(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O
Comments
n
A0
H
L
L
L
X
X
X
Ad d re ss and Co ntro l me e t se tup
n+1
X
X
H
X
L
X
X
X
Clo ck Se tup Valid , Ad vance Co unte r
n+2
X
X
H
X
L
X
L
Q0
Ad d re ss A0 Re ad Out, Inc. Co unt
n+3
X
X
H
X
L
X
L
Q0+1
Ad d re ss A0+1 Re ad Out, Inc. Co unt
n+4
X
X
H
X
L
X
L
Q0+2
Ad d re ss A0+2 Re ad Out, Inc. Co unt
n+5
A1
H
L
L
L
X
L
Q0+3
Ad d re ss A0+3 Re ad Out, Lo ad A1
n+6
X
X
H
X
L
X
L
Q0
Ad d re ss A0 Re ad Out, Inc. Co unt
n+7
X
X
H
X
L
X
L
Q1
Ad d re ss A1 Re ad Out, Inc. Co unt
n+8
A2
H
L
L
L
X
L
Q1+1
Ad d re ss A1+1 Re ad Out, Lo ad A2
5294 tb l 14
NOTES:
1. H = High; L = Low; X = Don’t Care; Z = High Impedance..
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
Write Operation(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O
Comments
n
A0
L
L
L
L
L
X
X
Ad d re ss and Co ntro l me e t se tup
n+1
X
X
X
X
L
X
X
X
Clo ck Se tup Valid
n+2
X
X
X
X
L
X
X
D0
Write to Ad d re ss A0
5294 tb l 15
NOTES:
1. H = High; L = Low; X = Don’t Care; Z = High Impedance.
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
Burst Write Operation(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O
Comments
n
A0
L
L
L
L
L
X
X
Ad d re ss and Co ntro l me e t se tup
n+1
X
X
H
X
L
L
X
X
Clo ck Se tup Valid , Inc. Co unt
n+2
X
X
H
X
L
L
X
D0
Ad d re ss A0 Write , Inc. Co unt
n+3
X
X
H
X
L
L
X
D0+1
Ad d re ss A0+1 Write , Inc. Co unt
n+4
X
X
H
X
L
L
X
D0+2
Ad d re ss A0+2 Write , Inc. Co unt
n+5
A1
L
L
L
L
L
X
D0+3
Ad d re ss A0+3 Write , Lo ad A1
n+6
X
X
H
X
L
L
X
D0
Ad d re ss A0 Write , Inc. Co unt
n+7
X
X
H
X
L
L
X
D1
Ad d re ss A1 Write , Inc. Co unt
n+8
A2
L
L
L
L
L
X
D1+1
Ad d re ss A1+1 Write , Lo ad A2
NOTES:
1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance.
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
6.42
10
Aug.12.20
5294 tb l 16
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Read Operation with Clock Enable Used(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O
Comments
n
A0
H
L
L
L
X
X
X
Ad d re ss and Co ntro l me e t se tup
n+1
X
X
X
X
H
X
X
X
Clo ck n+1 Ig no re d
n+2
A1
H
L
L
L
X
X
X
Clo ck Valid
n+3
X
X
X
X
H
X
L
Q0
Clo ck Ig no re d . Data Q0 is o n the b us.
n+4
X
X
X
X
H
X
L
Q0
Clo ck Ig no re d . Data Q0 is o n the b us.
n+5
A2
H
L
L
L
X
L
Q0
Ad d re ss A0 Re ad o ut (b us trans.)
n+6
A3
H
L
L
L
X
L
Q1
Ad d re ss A1 Re ad o ut (b us trans.)
n+7
A4
H
L
L
L
X
L
Q2
Ad d re ss A2 Re ad o ut (b us trans.)
5294 tb l 17
NOTES:
1. H = High; L = Low; X = Don’t Care; Z = High Impedance.
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
Write Operation with Clock Enable Used(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O
Comments
n
A0
L
L
L
L
L
X
X
Ad d re ss and Co ntro l me e t se tup .
n+1
X
X
X
X
H
X
X
X
Clo ck n+1 Ig no re d .
n+2
A1
L
L
L
L
L
X
X
Clo ck Valid .
n+3
X
X
X
X
H
X
X
X
Clo ck Ig no re d .
n+4
X
X
X
X
H
X
X
X
Clo ck Ig no re d .
n+5
A2
L
L
L
L
L
X
D0
Write Data D0
n+6
A3
L
L
L
L
L
X
D1
Write Data D1
n+7
A4
L
L
L
L
L
X
D2
Write Data D2
NOTES:
1. H = High; L = Low; X = Don’t Care; Z = High Impedance.
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
6.42
11
Aug.12.20
5294 tb l 18
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Read Operation with Chip Enable Used(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O(3)
Comments
n
X
X
L
H
L
X
X
?
De se le cte d .
n+1
X
X
L
H
L
X
X
?
De se le cte d .
n+2
A0
H
L
L
L
X
X
Z
Ad d re ss and Co ntro l me e t se tup
n+3
X
X
L
H
L
X
X
Z
De se le cte d o r STOP.
n+4
A1
H
L
L
L
X
L
Q0
Ad d re ss A0 Re ad o ut. Lo ad A1.
n+5
X
X
L
H
L
X
X
Z
De se le cte d o r STOP.
n+6
X
X
L
H
L
X
L
Q1
Ad d re ss A1 Re ad o ut. De se le cte d .
n+7
A2
H
L
L
L
X
X
Z
Ad d re ss and co ntro l me e t se tup .
n+8
X
X
L
H
L
X
X
Z
De se le cte d o r STOP.
n+9
X
X
L
H
L
X
L
Q2
Ad d re ss A2 Re ad o ut. De se le cte d .
5294 tb l 19
NOTES:
1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance.
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
3. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up.
Write Operation with Chip Enable Used(1)
Cycle
Address
R/W
ADV/LD
CE(2)
CEN
BWx
OE
I/O(3)
Comments
n
X
X
L
H
L
X
X
?
De se le cte d .
n+1
X
X
L
H
L
X
X
?
De se le cte d .
n+2
A0
L
L
L
L
L
X
Z
Ad d re ss and Co ntro l me e t se tup
n+3
X
X
L
H
L
X
X
Z
De se le cte d o r STOP.
n+4
A1
L
L
L
L
L
X
D0
Ad d re ss D0 Write in. Lo ad A1.
n+5
X
X
L
H
L
X
X
Z
De se le cte d o r STOP.
n+6
X
X
L
H
L
X
X
D1
Ad d re ss D1 Write in. De se le cte d .
n+7
A2
L
L
L
L
L
X
Z
Ad d re ss and co ntro l me e t se tup .
n+8
X
X
L
H
L
X
X
Z
De se le cte d o r STOP.
n+9
X
X
L
H
L
X
X
D2
Ad d re ss D2 Write in. De se le cte d .
NOTES:
1. H = High; L = Low; X = Don’t Care; ? = Don’t Know; Z = High Impedance.
2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L.
3. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up.
6.42
12
Aug.12.20
5294 tb l 20
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
DC Electrical Characteristics Over the Operating
Temperature and Supply Voltage Range (VDD = 3.3V±5%)
Symbol
Parameter
Test Conditions
Min.
Max.
Unit
|ILI|
Inp ut Le akag e Curre nt
VDD = Max., VIN = 0V to VDD
___
5
µA
|ILI|
LBO, JTAG and ZZ Inp ut Le akag e Curre nt(1)
VDD = Max., VIN = 0V to VDD
___
30
µA
5
µA
V
|ILO|
Outp ut Le akag e Curre nt
VOUT = 0V to VDDQ, De vice De se le cte d
___
VOL
Outp ut Lo w Vo ltag e
IOL = +6mA, VDD = Min.
___
0.4
VOH
Outp ut Hig h Vo ltag e
IOH = -6mA, VDD = Min.
2.0
___
V
5294 tb l 21
NOTE:
1. The LBO, TMS, TDI, TCK and TRST pins will be internally pulled to VDD and ZZ will be internally pulled to VSS if it is not actively driven in the application.
DC Electrical Characteristics Over the Operating
Temperature Supply Voltage Range(1) (VDD = 3.3V±5%)
150MHz
133MHz
100MHz
Unit
Symbol
Parameter
Test Conditions
Com'l
Ind'l
Com'l
Ind'l
Com'l
Ind'l
IDD
Op e rating Po we r
Sup p ly Curre nt
De vice Se le cte d , Outp uts Op e n,
ADV/LD = X, VDD = Max.,
VIN > VIH o r < VIL, f = fMAX(2)
325
335
300
310
250
260
mA
ISB1
CMOS Stand b y Po we r
Sup p ly Curre nt
De vice De se le cte d , Outp uts Op e n,
VDD = Max., VIN > VHD o r < VLD,
f = 0(2,3)
40
45
40
45
40
45
mA
ISB2
Clo ck Running Po we r
Sup p ly Curre nt
De vice De se le cte d , Outp uts Op e n,
VDD = Max., VIN > VHD o r < VLD,
f = fMAX(2.3)
120
130
110
120
100
110
mA
ISB3
Id le Po we r
Sup p ly Curre nt
De vice Se le cte d , Outp uts Op e n,
CEN > VIH, VDD = Max.,
VIN > VHD o r < VLD, f = fMAX(2,3)
40
45
40
45
40
45
mA
5294 tb l 22
NOTES:
1. All values are maximum guaranteed values.
2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC; f=0 means no input lines are changing.
3. For I/Os VHD = VDDQ – 0.2V, VLD = 0.2V. For other inputs VHD = VDD – 0.2V, VLD = 0.2V.
AC Test Loads
AC Test Conditions
VDDQ/2
(VDDQ = 2.5V)
50Ω
I/O
Z0 = 50Ω
,
5294 drw 04
Figure 1. AC Test Load
Inp ut Rise /Fall Time s
0 to 2.5V
2ns
Inp ut Timing Re fe re nce Le ve ls
(VDDQ/2)
6
Outp ut Timing Re fe re nce Le ve ls
(VDDQ/2)
5
AC Te st Lo ad
4
Se e Fig ure 1
5294 tb l 23
Δt CD 3
(Ty pi cal ,
2
ns )
1
20 30 50
80 100
Capaci t ance (pF )
200
5294 dr w05
Figure 2. Lumped Capacitive Load, Typical Derating
6.42
13
Aug.12.20
Inp ut Pulse Le ve ls
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
AC Electrical Characteristics
(VDD = 3.3V±5%, Commercial and Industrial Temperature Ranges)
150MHz
Symbol
100MHz
Min.
Max.
Min.
Max.
M i n.
Max.
Unit
Clo ck Cycle Time
6.7
____
7.5
____
10
____
ns
tF(1)
Clo ck Fre q ue nce
____
150
____
133
____
100
MHz
tCH(2)
Clo ck Hig h Pulse Wid th
2.0
____
2.2
____
3.2
____
ns
tCL(2)
Clo ck Lo w Pulse Wid th
2.0
____
2.2
____
3.2
____
ns
tCYC
Parameter
133MHz
Output Parameters
tCD
Clo ck Hig h to Valid Data
____
3.8
____
4.2
____
5
ns
tCDC
Clo ck Hig h to Data Chang e
1.5
____
1.5
____
1.5
____
ns
tCLZ(3,4,5)
Clo ck Hig h to Outp ut Active
1.5
____
1.5
____
1.5
____
ns
tCHZ(3,4,5)
Clo ck Hig h to Data Hig h-Z
1.5
3
1.5
3
1.5
3.3
ns
tOE
Outp ut Enab le Acce ss Time
____
3.8
____
4.2
____
5
ns
tOLZ(3,4)
Outp ut Enab le Lo w to Data Active
0
____
0
____
0
____
ns
tOHZ(3,4)
Outp ut Enab le Hig h to Data Hig h-Z
____
3.8
____
4.2
____
5
ns
Set Up Times
tSE
Clo ck Enab le Se tup Time
1.5
____
1.7
____
2.0
____
ns
tSA
Ad d re ss Se tup Time
1.5
____
1.7
____
2.0
____
ns
tSD
Data In Se tup Time
1.5
____
1.7
____
2.0
____
ns
tSW
Re ad /Write (R/W) Se tup Time
1.5
____
1.7
____
2.0
____
ns
tSADV
Ad vance /Lo ad (ADV/LD) Se tup Time
1.5
____
1.7
____
2.0
____
ns
1.7
____
2.0
____
ns
tSC
Chip Enab le /Se le ct Se tup Time
1.5
____
tSB
Byte Write Enab le (BWx) Se tup Time
1.5
____
1.7
____
2.0
____
ns
tHE
Clo ck Enab le Ho ld Time
0.5
____
0.5
____
0.5
____
ns
tHA
Ad d re ss Ho ld Time
0.5
____
0.5
____
0.5
____
ns
0.5
____
0.5
____
ns
0.5
____
0.5
____
ns
0.5
____
ns
Hold Times
tHD
Data In Ho ld Time
0.5
____
tHW
Re ad /Write (R/W) Ho ld Time
0.5
____
tHADV
Ad vance /Lo ad (ADV/LD) Ho ld Time
0.5
____
0.5
____
tHC
Chip Enab le /Se le ct Ho ld Time
0.5
____
0.5
____
0.5
____
ns
tHB
Byte Write Enab le (BWx) Ho ld Time
0.5
____
0.5
____
0.5
____
ns
5294 tb l 24
NOTES:
1. tF = 1/tCYC.
2. Measured as HIGH above 0.6VDDQ and LOW below 0.4VDDQ.
3. Transition is measured ±200mV from steady-state.
4. These parameters are guaranteed with the AC load (Figure 1) by device characterization. They are not production tested.
5. To avoid bus contention, the output buffers are designed such that tCHZ (device turn-off) is about 1ns faster than tCLZ (device turn-on) at a given temperature and voltage.
The specs as shown do not imply bus contention because tCLZ is a Min. parameter that is worse case at totally different test conditions (0 deg. C, 3.465V) than tCHZ,
which is a Max. parameter (worse case at 70 deg. C, 3.135V).
6.42
14
Aug.12.20
Aug.12.20
6.42
15
A1
tSADV
tHA
tHW
tHE
tCLZ
tHC
Pipeline
Read
tSC
A2
tSA
tSW
tSE
tCD
Pipeline
Read
Q(A1)
tHADV
tCH
tCDC
tCL
Q(A2)
O1(A2)
,
O2(A2)
Q(A
2+1)
Q(A2+2)
CEN high, eliminates
current L-H clock edge)
Burst Pipeline Read
tCD
Q(A2+2)
tCDC
Q(A2+3)
tCHZ
Q(A2)
5294 drw 06
(Burst Wraps around
to initial state)
NOTES:
1. Q (A1) represents the first output from the external address A1. Q (A2) represents the first output from the external address A2; Q (A2+1) represents the next output data in the burst sequence
of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input.
2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH.
3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW.
4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are
loaded into the SRAM.
DATAOUT
OE
BW1 - BW4
CE1, CE2(2)
ADDRESS
R/W
ADV/LD
CEN
CLK
tCYC
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Timing Waveform of Read Cycle(1,2,3,4)
Aug.12.20
6.42
16
A1
tSADV
tHW
tHE
tHB
tHC
Pipeline
Write
tSB
tSC
tHA
A2
tSA
tSW
tSE
tHD
Pipeline
Write
D(A1)
tSD
tHADV
tCH
D(A2)
tCL
D(A2+1)
Burst Pipeline Write
CEN high, eliminates
current L-H clock edge)
tSD
D(A2+2)
tHD
D(A2)
5294 drw 07
D(A2+3)
(Burst Wraps around
to initial state)
NOTES:
1. D (A1) represents the first input to the external address A1. D (A2) represents the first input to the external address A2; D (A2+1) represents the next input data in the burst sequence of
the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input.
2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH.
3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW.
4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are
loaded into the SRAM.
5. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before
the actual data is presented to the SRAM.
DATAIN
OE
BW1 - BW4
CE1, CE2(2)
ADDRESS
R/W
ADV/LD
CEN
CLK
tCYC
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Timing Waveform of Write Cycles(1,2,3,4,5)
Aug.12.20
6.42
17
A1
tSADV
tHW
tHE
tCD
tHB
tHC
Read
tSB
tSC
tHA
A2
tSA
tSW
tSE
A3
Q(A1)
tCHZ
Write
tHADV
tCH
tCLZ
Read
D(A2)
tSD tHD
A4
tCL
Q(A3)
tCDC
Write
A5
D(A4)
A6
Read
D(A5)
A7
Q(A6)
A8
5294 drw 08
Q(A7)
A9
NOTES:
1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2.
2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH.
3. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two
cycles before the actual data is presented to the SRAM.
DATAOUT
DATAIN
OE
BW1 - BW4
CE1, CE2(2)
ADDRESS
R/W
ADV/LD
CEN
CLK
tCYC
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Timing Waveform of Combined Read and Write Cycles (1,2,3)
Aug.12.20
6.42
18
A1
tSE
tSADV
tHE
tHW
tHC
tCD
tCLZ
tHB
B(A2)
tSB
tSC
tHA
A2
tSA
tSW
tCH
tHADV
Q(A1)
tCL
tCHZ
tCDC
Q(A1)
A3
D(A2)
tSD tHD
A4
NOTES:
1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2.
2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH.
3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propagating into the SRAM. The part will behave as if the L-H clock transition
did not occur. All internal registers in the SRAM will retain their previous state.
4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before
the actual data is presented to the SRAM.
DATAOUT
DATAIN
OE
BW1 - BW4
CE1, CE2(2)
ADDRESS
R/W
ADV/LD
CEN
CLK
tCYC
5294 drw 09
Q(A3)
A5
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Timing Waveform of CEN Operation(1,2,3,4)
,
Aug.12.20
6.42
19
A1
tSADV
tHW
tHE
tSC
tCLZ
tCD
tHC
tHA
A2
tSA
tSW
tSE
Q(A1)
tHADV
tCH
tCDC
tCHZ
tHB
Q(A2)
tSB
A3
tCL
D(A3)
tSD tHD
A4
Q(A4)
A5
5294 drw 10
,
NOTES:
1. Q (A1) represents the first output from the external address A1. D (A3) represents the input data to the SRAM corresponding to address A3.
2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH.
3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propagating into the SRAM. The part will behave as if the L-H clock transition
did not occur. All internal registers in the SRAM will retain their previous state.
4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before
the actual data is presented to the SRAM.
DATAOUT
DATAIN
OE
BW1 - BW4
CE1, CE2(2)
ADDRESS
R/W
ADV/LD
CEN
CLK
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Timing Waveform of CS Operation(1,2,3,4)
71V2546, 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Timing Waveform of OE Operation(1)
OE
tOE
tOHZ
tOLZ
DATAOUT
Valid
5294 drw 11
NOTE:
1. A read operation is assumed to be in progress.
Ordering Information
XXXX
Device
Type
XX
XX
Power Speed
XX
Package
X
X
X
Process/
Temperature
Range
Blank
8
Tray
Tape and Reel
Blank
I(1)
Commercial (0°C to +70°C)
Industrial (-40°C to +85°C)
G(2)
Green
PF
BG
100-pin Plastic Thin Quad Flatpack (PKG100)
119 Ball Grid Array (BG119)
150
133
100
Clock Frequency in Megahertz
S
Standard Power
71V2546 128Kx36 Pipelined ZBT SRAM with 2.5V I/O
5294 drw 12
NOTES:
1. Contact your local sales office for Industrial temp range for other speeds, packages and powers.
2. Green parts available. For specific speeds, packages and powers contact your local sales office.
6.42
20
Aug.12.20
71V2546 128K x 36, 3.3V Synchronous ZBT™ SRAM
with 2.5V I/O, Burst Counter, and Pipelined Outputs
Commercial and Industrial Temperature Ranges
Orderable Part Information
Speed
(MHz)
100
133
150
Pkg.
Code
Pkg.
Type
Temp.
Grade
71V2546S100BG
BG119
PBGA
C
71V2546S100BG8
BG119
PBGA
C
Orderable Part ID
71V2546S100BGI
BG119
PBGA
I
71V2546S100BGI8
BG119
PBGA
I
71V2546S100PFG
PKG100
TQFP
C
71V2546S100PFG8
PKG100
TQFP
C
71V2546S133BG
BG119
PBGA
C
71V2546S133BG8
BG119
PBGA
C
71V2546S133BGI
BG119
PBGA
I
71V2546S133BGI8
BG119
PBGA
I
71V2546S133PFG
PKG100
TQFP
C
71V2546S133PFG8
PKG100
TQFP
C
BG119
PBGA
C
71V2546S150BG8
BG119
PBGA
C
71V2546S150PFG
PKG100
TQFP
C
71V2546S150PFG8
PKG100
TQFP
C
71V2546S150BG
Datasheet Document History
12/31/99
03/04/00
05/02/00
05/26/00
07/26/00
Pg. 1,14,15,22
Pg. 5,6
Pg. 5,6,7
Pg. 6
Pg. 21
Pg. 23
Pg. 5-8
Pg. 8
Pg. 23
10/25/00
05/20/02
09/30/04
Pg. 8
Pg. 1-8,15,22,23,27
Pg. 7
02/23/07
05/27/10
04/11/11
Pg. 27
Pg. 24
Pg. 1-21
Pg. 13
Pg. 20
08/12/20
Pg. 1 - 22
Pg. 1 & 20
Pg. 4 - 5
Pg. 20
Pg. 21
Created preliminary datasheet from 71V2556 and 71V2558 datasheets. Changed tCDC, tCLZ,
and tCHZ minimums from 1.0ns to 1.5ns.
Add 150 MHz speed grade offering
Insert clarification note to Recommended Operating Temperature and Absolute Max Ratings tables
Clarify note on TQFP and BGA pin configurations; corrected typo in pinout
Add BGA capacitance table
Add 100 pin TQFP Package Diagram Outline
Add new package offering, 13 x 15mm 165 fBGA
Correct 119 BGA Package Diagram Outline
Add ZZ, sleep mode reference note to BG119, PK100 and BQ165 pinouts
Update BQ165 pinout
Update BG119 Package Diagram Outline dimensions
Remove Preliminary status from datasheet
Add reference note to pin N5 on BQ165, reserved for JTAG pin TRST
Added JTAG "SA" version functionality and updated ZZ pin descriptions and notes
Updated pin configuration for the 119 BGA-reordered I/O signals on P6, P7 (128K x 36)
and P7, N6, L6, K7, H6, G7, F6, E7, D6 (256K x 18).
Added X step die generation to data sheet ordering information.
Added "Restricted hazardous substance device" to the ordering information.
Removed 71V2548 (EOL), fBGA 165 pin, and JTAG information.
Added 150MHz data for Industrial information.
Added Tape and Reel to Ordering information and updated description of Restricted hazardous
substance device to Green.
Rebranded as Renesas datasheet
Updated Industrial temp range and green availability
Updated package codes
Removed X generation die stepping from Ordering Information
Added Orderable Part Information table
6.42
21
Aug.12.20
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.