74CBTLV3125QG

IDT74CBTLV3125 LOW-VOLTAGE QUADRUPLE BUS SWITCH INDUSTRIAL TEMPERATURE RANGE LOW-VOLTAGE QUADRUPLE BUS SWITCH FEATURES: IDT74CBTLV3125 APPLICATIONS: • • • • • • • Pin-out compatible with standard '125 Logic products Ω A/B bi-directional bus switch 5Ω Isolation under power-off conditions Over-voltage tolerant Latch-up performance exceeds 100mA VCC = 2.3V - 3.6V, Normal Range ESD > 2000V per MIL-STD-883, Method 3015; > 200V using machine model (C = 200pF, R = 0) • Available in QSOP and TSSOP packages The CBTLV3125 features four independent switches. Each switch is enabled when the associated output-enable (OE) input is low. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. FUNCTIONAL BLOCK DIAGRAM SIMPLIFIED SCHEMATIC, EACH SWITCH • 3.3V High Speed Bus Switching and Bus Isolation DESCRIPTION: NOTE: 1. Pin numbers shown apply to the 14-pin TSSOP package. The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE DECEMBER 2014 1 © 2014 Integrated Device Technology, Inc. All rights reserved. Product specifications subject to change without notice. DSC-5744/8 IDT74CBTLV3125 LOW-VOLTAGE QUADRUPLE BUS SWITCH INDUSTRIAL TEMPERATURE RANGE PIN CONFIGURATION TSSOP TOP VIEW QSOP TOP VIEW ABSOLUTE MAXIMUM RATINGS(1) Symbol Description FUNCTION TABLE(1) Max Unit Input OE Inputs/Outputs L A Port = B Port H Disconnect VCC SupplyVoltage Range –0.5 to +4.6 V VI Input Voltage Range –0.5 to +4.6 V Continuous Channel Current 128 mA IIK Input Clamp Current, VI/O < 0 –50 mA TSTG Storage Temperature –65 to +150 °C NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level NOTE: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. OPERATING CHARACTERISTICS, TA = 25°C(1) Symbol Parameter VCC Supply Voltage VIH High-Level Control Input Voltage VIL TA Low-Level Control Input Voltage Test Conditions Min. Max. Unit 2.3 3.6 V VCC = 2.3V to 2.7V 1.7 — V VCC = 2.7V to 3.6V 2 — VCC = 2.3V to 2.7V — 0.7 VCC = 2.7V to 3.6V — 0.8 −40 85 Operating Free-Air Temperature NOTE: 1. All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. 2 V °C IDT74CBTLV3125 LOW-VOLTAGE QUADRUPLE BUS SWITCH INDUSTRIAL TEMPERATURE RANGE DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: Operating Conditions: TA = –40°C to +85°C Symbol VIK II IOZ Parameter Test Conditions Min. Typ.(1) Max. Unit — — –1.2 V Control Inputs, Data Inputs VCC = 3V, II = –18mA Control Inputs VCC = 3.6V, VI = VCC or GND — — ±1 μA Data I/O VCC = 3.6V, VO = 0 or 3.6V, switch disabled — — 5 μA VCC = 0, VI or VO = 0 to 3.6V — — 50 μA IOFF VCC = 3.6V, IO = 0, VI = VCC or GND — — 10 μA ΔICC(2) ICC Control Inputs VCC = 3.6V, one input at 3V, other inputs at VCC or GND — — 300 μA CI Control Inputs VI = 3V or 0 — 4 — pF VO = 3V or 0, OE = VCC VI = 0 — — — — — — — 6 5 5 27 5 5 10 — 8 8 40 7 7 15 pF CIO(OFF) VCC = 2.3V Typ. at VCC = 2.5V RON(3) IO = 64mA IO = 24mA IO = 15mA IO = 64mA IO = 24mA IO = 15mA VI = 1.7V VI = 0 VCC = 3V VI = 2.4V Ω NOTES: 1. Typical values are at VCC = 3.3V, +25°C ambient. 2. The increase in supply current is attributable to each current that is at the specified voltage level rather than VCC or GND. 3. This is measured by the voltage drop between the A and B terminals at the indicated current through the switch. SWITCHING CHARACTERISTICS VCC = 2.5V ± 0.2V Symbol tPD(1) Parameter Propagation Delay VCC = 3.3V ± 0.3V Min. Max. Min. Max. Unit − 0.15 − 0.25 ns 1 4.6 1 4.4 ns 1 3.9 1 4.2 ns A to B or B to A tEN Output Enable Time OE to A or B tDIS Output Disable Time OE to A or B NOTE: 1. The propagation delay is the calculated RC time constant of the typical on-state resistance of the switch and the specified load capacitance driven by an ideal voltage source (zero output impedance). 3 IDT74CBTLV3125 LOW-VOLTAGE QUADRUPLE BUS SWITCH INDUSTRIAL TEMPERATURE RANGE TEST CIRCUITS AND WAVEFORMS SAME PHASE INPUT TRANSITION TEST CONDITIONS Symbol VCC(1)= 3.3V±0.3V VCC(2)= 2.5V±0.2V Unit VLOAD 6 2 x Vcc V VIH 3 Vcc V VT 1.5 Vcc / 2 V VLZ 300 150 mV VHZ 300 150 mV CL 50 30 pF 500Ω Pulse Generator VIN tPHL VIH VT 0V DISABLE ENABLE CONTROL INPUT GND tPZL VOUT D.U.T. RT tPLH Propagation Delay Open (1, 2) tPHL OPPOSITE PHASE INPUT TRANSITION VLOAD VCC tPLH OUTPUT OUTPUT SWITCH NORMALLY CLOSED LOW tPZH OUTPUT SWITCH NORMALLY OPEN HIGH 500Ω CL tPLZ VLOAD/2 VT tPHZ V T 0V Test Circuits for All Outputs Enable and Disable Times DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. NOTES: 1. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2.5ns; tR ≤ 2.5ns. 2. Pulse Generator for All Pulses: Rate ≤ 10MHz; tF ≤ 2ns; tR ≤ 2.5ns. SWITCH POSITION Test Switch tPLZ/tPZL VLOAD tPHZ/tPZH GND tPD Open VIH VT 0V VOH VT VOL 4 VIH VT 0V VLOAD/2 VOL + VLZ VOL VOH VOH -VHZ 0V IDT74CBTLV3125 LOW-VOLTAGE QUADRUPLE BUS SWITCH INDUSTRIAL TEMPERATURE RANGE ORDERING INFORMATION CBTLV XXX XX XX Device Type Package Temp. Range X Blank 8 Tube or Tray Tape and Reel QG PGG Quarter-size Small Outline Package - Green Thin Shrink Small Outline Package - Green 3125 Low-Voltage Quadruple Bus Switch 74 –40°C to +85°C Datasheet Document History 07/14/2008 12/04/2014 Pg. 1 Pg. 5 Updated IDT Logo. Updated the ordering information by removing the "IDT" notation, non RoHS part and by adding Tape and Reel information. CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com 5 for Tech Support: logichelp@idt.com IMPORTANT NOTICE AND DISCLAIMER RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. Renesas grants you permission to use these resources only for development of an application that uses Renesas products. Other reproduction or use of these resources is strictly prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property. Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims, damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources expands or otherwise alters any applicable warranties or warranty disclaimers for these products. (Rev.1.0 Mar 2020) Corporate Headquarters Contact Information TOYOSU FORESIA, 3-2-24 Toyosu, Koto-ku, Tokyo 135-0061, Japan www.renesas.com For further information on a product, technology, the most up-to-date version of a document, or your nearest sales office, please visit: www.renesas.com/contact/ Trademarks Renesas and the Renesas logo are trademarks of Renesas Electronics Corporation. All trademarks and registered trademarks are the property of their respective owners. © 2020 Renesas Electronics Corporation. All rights reserved.