IDT74FCT157AT/CT/DT
FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
FAST CMOS
QUAD 2-INPUT
MULTIPLEXER
DESCRIPTION:
FEATURES:
•
•
•
•
•
•
•
•
IDT74FCT157AT/CT/DT
OBSOLETE PART
The FCT157T is a high-speed quad 2-input multiplexer built using an
advanced dual metal CMOS technology. Four bits of data from two sources
can be selected using the common select input. The four buffered outputs
present the selected data in the true (non-inverting) form.
The FCT157T has a common, active-low, enable input. When the
enable input is not active, all four outputs are held low. A common application
of FCT157T is to move data from two different groups of registers to a
common bus. Another application is as a function generator. The FCT157T
can generate any four of the 16 different functions of two variables with one
variable common.
A, C, and D grades
Low input and output leakage ≤1µA (max.)
CMOS power levels
True TTL input and output compatibility:
– VOH = 3.3V (typ.)
– VOL = 0.3V (typ.)
High Drive outputs (-15mA IOH, 48mA IOL)
Meets or exceeds JEDEC standard 18 specifications
Power off disable outputs permit "live insertion"
Available in SOIC and QSOP packages
R
T
O
R
F
A
P ED
E
D
T
S
N
E
N
E
L
G
M
O
I
S
M
S
B
E
O
O EC
D
R EW
T
N
O
N
FUNCTIONAL BLOCK DIAGRAM
S
E
Three other multiplexers
I1B I1D
Z B ZD
I0B I0D
I1A
ZA
I0A
INDUSTRIAL TEMPERATURE RANGE
AUGUST 2009
1
© 2009 Integrated Device Technology, Inc.
DSC-5502/6
IDT74FCT157AT/CT/DT
FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
ABSOLUTE MAXIMUM RATINGS(1)
PIN CONFIGURATION
S
1
16
VCC
I0A
2
15
E
I1A
3
14
I0C
ZA
4
13
I1C
I0B
5
12
ZC
I1B
6
11
I0D
ZB
7
10
I1D
GND
8
9
ZD
Symbol
Description
VTERM(2)
Max
Unit
VTERM(3)
Terminal Voltage with Respect to GND
–0.5 to +7
V
Terminal Voltage with Respect to GND
–0.5 to VCC+0.5
V
TSTG
Storage Temperature
–65 to +150
°C
IOUT
DC Output Current
–60 to +120
mA
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability. No terminal voltage may exceed
Vcc by +0.5V unless otherwise noted.
2. Inputs and Vcc terminals only.
3. Output and I/O terminals only.
CAPACITANCE (TA = +25°C, F = 1.0MHz)
Parameter(1)
Symbol
Conditions
Typ.
Max.
CIN
Input Capacitance
VIN = 0V
6
10
pF
COUT
Output Capacitance
VOUT = 0V
8
12
pF
NOTE:
1. This parameter is measured at characterization but not tested.
SOIC/ QSOP
TOP VIEW
PIN DESCRIPTION
Pin Names
Description
I0A - I0D
Source 0 Data Inputs
I1A - I1D
Source 1 Data Inputs
Enable Input (Active LOW)
E
S
Select Input
ZA - ZD
Outputs
FUNCTION TABLE(1)
Inputs
E
H
L
L
L
L
S
X
H
H
L
L
NOTE:
1. H = HIGH Voltage Level
X = Don’t Care
L = LOW Voltage Level
Z = High Impedance
2
Unit
I0
X
X
X
L
H
I1
X
L
H
X
X
Outputs
Zx
L
L
H
L
H
IDT74FCT157AT/CT/DT
FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Industrial: TA = –40°C to +85°C, VCC = 5.0V ±5%
Symbol
Test Conditions(1)
Min.
Typ.(2)
Max.
Unit
VIH
Input HIGH Level
Guaranteed Logic HIGH Level
2
—
—
V
VIL
Input LOW Level
Guaranteed Logic LOW Level
—
—
0.8
V
IIH
Input HIGH Current(4)
VCC = Max.
VI = 2.7V
—
—
±1
µA
IIL
Input LOW Current(4)
VCC = Max.
VI = 0.5V
—
—
±1
µA
High Impedance Output Current(4)
VCC = Max., VI = VCC (Max.)
VI = 2.7V
—
—
±1
µA
VI = 0.5V
—
—
±1
—
—
±1
—
–0.7
–1.2
V
—
200
—
mV
—
0.01
1
mA
Min.
2.4
2
—
Typ.(2)
3.3
3
0.3
Max.
—
—
0.5
Unit
V
–60
–120
–225
mA
—
—
±1
µA
IOZH
Parameter
IOZL
II
Input HIGH Current(4)
VCC = Max., VI = VCC (Max.)
VIK
Clamp Diode Voltage
VCC = Min., IIN = –18mA
VH
Input Hysteresis
ICC
Quiescent Power Supply Current
—
VCC = Max.
VIN = GND or VCC
µA
OUTPUT DRIVE CHARACTERISTICS
Symbol
VOH
Parameter
Output HIGH Voltage
Test Conditions(1)
IOH = –8mA
IOH = –15mA
IOL = 48mA
VOL
Output LOW Voltage
IOS
Short Circuit Current
VCC = Min
VIN = VIH or VIL
VCC = Min
VIN = VIH or VIL
VCC = Max., VO = GND(3)
IOFF
Input/Output Power Off Leakage(5)
VCC = 0V, VIN or VO ≤ 4.5V
NOTES:
1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Not more than one output should be tested at one time. Duration of the test should not exceed one second.
4. The test limit for this parameter is ±5µA at TA = –55°C.
5. This parameter is guaranteed but not tested.
3
V
IDT74FCT157AT/CT/DT
FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Test Conditions(1)
Min.
Typ.(2)
Max.
Unit
—
0.5
2
mA
VIN = VCC
VIN = GND
—
0.15
0.25
mA/
MHz
VCC = Max.
Outputs Open
fo = 10MHz
VIN = VCC
VIN = GND
—
1.5
3.5
mA
50% Duty Cycle
E = GND
One Bit Toggling
VIN = 3.4V
VIN = GND
—
1.8
4.5
VCC = Max.
Outputs Open
fo = 2.5MHz
VIN = VCC
VIN = GND
—
1.5
3.5(5)
50% Duty Cycle
E = GND
Four Bits Toggling
VIN = 3.4V
VIN = GND
—
2.5
7.5(5)
Symbol
Parameter
ΔICC
Quiescent Power Supply Current
TTL Inputs HIGH
VCC = Max.
VIN = 3.4V(3)
ICCD
Dynamic Power Supply
Current(4)
VCC = Max.
Outputs Open
E = GND
One Input Toggling
50% Duty Cycle
IC
Total Power Supply Current(6)
mA
NOTES:
1. For conditions shown as Min. or Max., use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at VCC = 5.0V, +25°C ambient.
3. Per TTL driven input (VIN = 3.4V). All other inputs at VCC or GND.
4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations.
5. Values for these conditions are examples of ΔICC formula. These limits are guaranteed but not tested.
6. IC = IQUIESCENT + IINPUTS + IDYNAMIC
IC = ICC + ΔICC DHNT + ICCD (fONO)
ICC = Quiescent Current
ΔICC = Power Supply Current for a TTL High Input (VIN = 3.4V)
DH = Duty Cycle for TTL Inputs High
NT = Number of TTL Inputs at DH
ICCD = Dynamic Current caused by an Input Transition Pair (HLH or LHL)
fO = Output Frequency
NO = Number of Outputs at fO
All currents are in milliamps and all frequencies are in megahertz.
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
Symbol
tPLH
tPHL
tPLH
tPHL
tPLH
tPHL
IDT74FCT151AT
IDT74FCT151CT
IDT74FCT151DT
Parameter
Condition(1)
Min.(2)
Max.
Min.(2)
Max.
Min.(2)
Max.
Unit
Propagation Delay
Ix to Zx
Propagation Delay
E to Zx
Propagation Delay
S to Zx
CL = 50pF
RL = 500Ω
1.5
5
1.5
4.3
1.5
3.9
ns
1.5
6
1.5
4.8
1.5
4.4
ns
1.5
7
1.5
5.2
1.5
4.6
ns
NOTES:
1. See test circuit and waveforms.
2. Minimum limits are guaranteed but not tested on Propagation Delays.
4
IDT74FCT157AT/CT/DT
FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
TEST CIRCUITS AND WAVEFORMS
V CC
SWITCH POSITION
7.0V
500W
V OUT
VIN
Pulse
Generator
D.U.T
.
50pF
RT
500W
Test
Switch
Open Drain
Disable Low
Enable Low
Closed
All Other Tests
Open
DEFINITIONS:
CL = Load capacitance: includes jig and probe capacitance.
RT = Termination resistance: should be equal to ZOUT of the Pulse Generator.
CL
Octal Link
Test Circuits for All Outputs
DATA
INPUT
tH
tSU
TIMING
INPUT
ASYNCHRONOUS CONTROL
PRESET
CLEAR
ETC.
SYNCHRONOUS CONTROL
PRESET
CLEAR
CLOCK ENABLE
ETC.
tREM
tSU
3V
1.5V
0V
3V
1.5V
0V
LOW-HIGH-LOW
PULSE
1.5V
tW
3V
1.5V
0V
HIGH-LOW-HIGH
PULSE
1.5V
3V
1.5V
0V
tH
Pulse Width
Octal Link
Octal Link
Set-Up, Hold, and Release Times
ENABLE
SAME PHASE
INPUT TRANSITION
tPLH
tPHL
OUTPUT
tPLH
OPPOSITE PHASE
INPUT TRANSITION
tPHL
3V
1.5V
0V
VOH
1.5V
VOL
DISABLE
3V
1.5V
0V
CONTROL
INPUT
tPZL
OUTPUT
NORMALLY
LOW
3V
1.5V
0V
SWITCH
CLOSED
tPLZ
3.5V
1.5V
tPZH
OUTPUT
NORMALLY
HIGH
SWITCH
OPEN
3.5V
0.3V
VOL
tPHZ
0.3V
1.5V
0V
Octal Link
VOH
0V
Octal Link
Propagation Delay
Enable and Disable Times
NOTES:
1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
2. Pulse Generator for All Pulses: Rate ≤ 1.0MHz; tF ≤ 2.5ns; tR ≤ 2.5ns.
5
IDT74FCT157AT/CT/DT
FAST CMOS QUAD 2-INPUT MULTIPLEXER
INDUSTRIAL TEMPERATURE RANGE
ORDERING INFORMATION
XX
FCT
Temperature
Range
XXXX
Device
Type
X
Package
SOG
QG
Small Outline IC (300 mil) - Green
Quarter-size Small Outline Package - Green
157AT Quad 2-Input Multiplexer
157CT
157DT
74
- 40 C to +85 C
Datasheet Document History
09/06/2009
01/23/2015
07/22/2019
Pg.6
Updated the ordering information by removing the "IDT" notation and non RoHS part.
PDN# CQ-15-01 issued. See IDT.com for PDN specifics.
Datasheet changed to Obsolete Status.
CORPORATE HEADQUARTERS
6024 Silver Creek Valley Road
San Jose, CA 95138
for SALES:
800-345-7015 or 408-284-8200
fax: 408-284-2775
www.idt.com
6
for Tech Support:
logichelp@idt.com
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.