FemtoClock® Crystal-to-LVCMOS/ LVTTL
Frequency Synthesizer
840004I-01
Datasheet
General Description
Features
The 840004I-01 is a 4 output LVCMOS/LVTTL Synthesizer
optimized to generate Ethernet reference clock frequencies. Using
a 25MHz, 18pF parallel resonant crystal, the following frequencies
can be generated based on the 2 frequency select pins
(F_SEL1:0): 156.25MHz, 125MHz, and 62.5MHz. The 840004I-01
uses IDT’s 3rd generation low phase noise VCO technology and
can achieve 1ps or lower typical random rms phase jitter, easily
meeting Ethernet jitter requirements. The 840004I-01 is packaged
in a small 20-pin TSSOP package.
•
Four single-ended LVCMOS/LVTTL outputs
17 typical output impedance
•
Selectable crystal oscillator interface or single-ended input,
Supports the following output frequencies: 156.25MHz,
125MHz and 62.5MHz
•
•
VCO range: 560MHz - 700MHz
•
Output supply modes:
Core/Output
3.3V/3.3V
3.3V/2.5V
2.5V/2.5V
•
•
•
-40°C to 85°C ambient operating temperature
RMS phase jitter at 156.25MHz (1.875MHz – 20MHz):
0.52ps (typical)
Available in lead-free (RoHS 6) package
For functional replacement part use 8T49N241
Frequency Select Function Table for Ethernet Frequencies
Inputs
F_SEL1
F_SEL0
M Div. Value
N Div. Value
M/N Ratio Value
Output Frequency (MHz), (25MHz Reference)
0
0
25
4
6.25
156.25
0
1
25
5
5
125
1
0
25
10
2.5
62.5
1
1
25
5
5
125 (default)
Pin Assignment
Block Diagram
OE
F_SEL1:0
Pullup
nPLL_SEL
Pulldown
nXTAL_SEL
Pulldown
F_SEL0
nc
nXTAL_SEL
REF_CLK
2
Pullup:Pullup
25MHz
XTAL_IN
OSC
F_SEL1:0
0
1
XTAL_OUT
REF_CLK
Pulldown
1
Phase
Detector
VCO
0
00
01
10
11
N
÷4
÷5
÷10
÷5 (default)
Q0
Q1
Q2
M = ÷25 (fixed)
MR
Q3
OE
MR
nPLL_SEL
VDDA
nc
VDD
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
F_SEL1
GND
Q0
Q1
VDDO
Q2
Q3
GND
XTAL_IN
XTAL_OUT
840004I-01
20-Lead TSSOP
6.5mm x 4.4mm x 0.925mm
package body
G Package
Top View
Pulldown
©2016 Integrated Device Technology, Inc.
1
Revision D, November 7, 2016
840004I-01 Datasheet
Table 1. Pin Descriptions
Number
Name
1, 20
F_SEL0,
F_SEL1
Type
Description
Input
2, 9
nc
Unused
3
nXTAL_SEL
Input
Pulldown
Selects between the crystal or REF_CLK inputs as the PLL reference
source. When HIGH, selects REF_CLK. When LOW, selects XTAL
inputs. LVCMOS/LVTTL interface levels.
4
REF_CLK
Input
Pulldown
Single-ended reference clock input. LVCMOS/LVTTL interface levels.
5
OE
Input
Pullup
Output enable pin. When HIGH, the outputs are active. When LOW, the
outputs are in a high impedance state. LVCMOS/LVTTL interface levels.
6
MR
Input
Pulldown
Active HIGH master reset. When logic HIGH, the internal dividers are
reset causing the outputs to go low. When logic LOW, the internal
dividers and the outputs are enabled. LVCMOS/LVTTL interface levels.
7
nPLL_SEL
Input
Pulldown
PLL bypass. When LOW, the output is driven from the VCO output.
When HIGH, the PLL is bypassed and the output frequency = reference
clock frequency/N output divider. LVCMOS/LVTTL interface levels.
8
VDDA
Power
Analog supply pin.
Core supply pin.
Pullup
Frequency select pins. LVCMOS/LVTTL interface levels.
No connect.
10
VDD
Power
11,
12
XTAL_OUT,
XTAL_IN
Input
13, 19
GND
Power
Power supply ground.
14, 15, 17, 18
Q3, Q2, Q1, Q0
Output
Single-ended clock outputs. 17 typical output impedance.
LVCMOS/ LVTTL interface levels.
16
VDDO
Power
Output supply pin.
Crystal oscillator interface. XTAL_IN is the input. XTAL_OUT is the
output.
NOTE: Pullup and Pulldown refer to internal input resistors. See Table 2, Pin Characteristics, for typical values.
Table 2. Pin Characteristics
Symbol
Parameter
Test Conditions
CIN
Input Capacitance
4
pF
CPD
Power Dissipation Capacitance
8
pF
RPULLUP
Input Pullup Resistor
51
k
51
k
VDDO = 3.3V±5%
17
VDDO = 2.5V±5%
21
RPULLDOWN Input Pulldown Resistor
ROUT
Output Impedance
©2016 Integrated Device Technology, Inc.
2
Minimum
Typical
Maximum
Units
Revision D, November 7, 2016
840004I-01 Datasheet
Absolute Maximum Ratings
NOTE: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device.
These ratings are stress specifications only. Functional operation of product at these conditions or any conditions beyond
those listed in the DC Characteristics or AC Characteristics is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect product reliability.
Item
Rating
Supply Voltage, VDD
4.6V
Inputs, VI
-0.5V to VDD + 0.5V
Outputs, VO
-0.5V to VDDO + 0.5V
Package Thermal Impedance, JA
73.2C/W (0 lfpm)
Storage Temperature, TSTG
-65C to 150C
DC Electrical Characteristics
Table 3A. Power Supply DC Characteristics, VDD = 3.3V ± 5%, VDDO = 3.3V ± 5% or 2.5V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
VDD
Test Conditions
Minimum
Typical
Maximum
Units
Core Supply Voltage
3.135
3.3
3.465
V
VDDA
Analog Supply Voltage
3.135
3.3
3.465
V
3.135
3.3
3.465
V
VDDO
Output Supply Voltage
2.375
2.5
2.625
V
IDD
Power Supply Current
100
mA
IDDA
Analog Supply Current
12
mA
IDDO
Output Supply Current
10
mA
Table 3B. Power Supply DC Characteristics, VDD = 2.5V ± 5%, VDDO = 2.5V ± 5%, TA = -40°C to 85°C
Symbol
Parameter
VDD
Minimum
Typical
Maximum
Units
Core Supply Voltage
2.375
2.5
2.625
V
VDDA
Analog Supply Voltage
2.375
2.5
2.625
V
VDDO
Output Supply Voltage
2.375
2.5
2.625
V
IDD
Power Supply Current
95
mA
IDDA
Analog Supply Current
12
mA
IDDO
Output Supply Current
8
mA
©2016 Integrated Device Technology, Inc.
Test Conditions
3
Revision D, November 7, 2016
840004I-01 Datasheet
Table 3C. LVCMOS/LVTTL DC Characteristics, TA = -40°C to 85°C
Symbol
Parameter
VIH
Input High Voltage
VIL
Input Low Voltage
IIH
IIL
Input
High Current
Input
Low Current
Test Conditions
Minimum
VDD = 3.465V
Typical
Maximum
Units
2
VDD + 0.3
V
VDD = 2.625V
1.7
VDD + 0.3
V
VDD = 3.465V
-0.3
0.8
V
VDD = 2.625V
-0.3
0.7
V
nXTAL_SEL,
nPLL_SEL,
REF_CLK, MR
VDD = VIN = 3.465V or 2.625V
150
µA
OE, F_SEL[0:1]
VDD = VIN = 3.465V or 2.625V
5
µA
nXTAL_SEL,
nPLL_SEL,
REF_CLK, MR
VDD = 3.465V or 2.625V, VIN = 0V
-5
µA
OE, F_SEL[0:1]
VDD = 3.465V or 2.625V, VIN = 0V
-150
µA
VDDO = 3.3V ± 5%
2.6
V
VDDO = 2.5V ± 5%
1.8
V
VOH
Output High Voltage; NOTE 1
VOL
Output Low Voltage; NOTE 1
VDDO = 3.3V ± 5% or 2.5V ± 5%
0.5
V
NOTE 1: Outputs terminated with 50 to VDDO/2. See Parameter Measurement Information section. Load Test Circuit diagrams.
Table 4. Crystal Characteristics
Parameter
Test Conditions
Mode of Oscillation
Minimum
Typical
Maximum
Units
Fundamental
Frequency
25
MHz
Equivalent Series Resistance (ESR)
50
Shunt Capacitance
7
pF
Drive Level
1
mW
©2016 Integrated Device Technology, Inc.
4
Revision D, November 7, 2016
840004I-01 Datasheet
AC Electrical Characteristics
Table 5A. AC Characteristics, VDD = VDDO = 3.3V ± 5%, TA = -40°C to 85°C
Parameter
fout
tsk(o)
tjit(Ø)
Symbol
Output Frequency
Test Conditions
Minimum
Typical
Maximum
Units
F_SEL[1:0] = 00
140
156.25
175
MHz
F_SEL[1:0] = 01 or 11
112
125
140
MHz
F_SEL[1:0] = 10
56
62.5
70
MHz
60
MHz
Output Skew: NOTE 1, 2
RMS Phase Jitter (Random);
NOTE 3
t R / tF
Output Rise/Fall Time
odc
Output Duty Cycle
156.25MHz, Integration Range:
1.875MHz – 20MHz
0.52
ps
125MHz, Integration Range:
1.875MHz – 20MHz
0.65
ps
62.5MHz, Integration Range:
1.875MHz – 20MHz
0.55
ps
20% to 80%
250
750
ps
F_SEL[1:0] = 00, 01 or 11
42
58
%
F_SEL[1:0] = 10
49
51
%
NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device
is mounted in a test socket with maintained transverse airflow greater than 500 lfpm. The device will meet specifications after thermal
equilibrium has been reached under these conditions.
NOTE 1: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDDO/2.
NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.
NOTE 3: Please refer to the Phase Noise Plot.
Table 5B. AC Characteristics, VDD = 3.3V ± 5%, VDDO = 2.5V ± 5%, TA = -40°C to 85°C
Parameter
fout
tsk(o)
tjit(Ø)
Symbol
Output Frequency
Test Conditions
Minimum
Typical
Maximum
Units
F_SEL[1:0] = 00
140
156.25
175
MHz
F_SEL[1:0] = 01 or 11
112
125
140
MHz
F_SEL[1:0] = 10
56
62.5
70
MHz
60
MHz
Output Skew: NOTE 1, 2
RMS Phase Jitter (Random);
NOTE 3
t R / tF
Output Rise/Fall Time
odc
Output Duty Cycle
156.25MHz, Integration Range:
1.875MHz – 20MHz
0.48
ps
125MHz, Integration Range:
1.875MHz – 20MHz
0.59
ps
62.5MHz, Integration Range:
1.875MHz – 20MHz
0.53
ps
20% to 80%
250
750
ps
F_SEL[1:0] = 00, 01 or 11
42
58
%
F_SEL[1:0] = 10
49
51
%
NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the device
is mounted in a test socket with maintained transverse airflow greater than 500 lfpm. The device will meet specifications after thermal
equilibrium has been reached under these conditions.
NOTE 1: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDDO/2.
NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.
NOTE 3: Please refer to the Phase Noise Plot.
©2016 Integrated Device Technology, Inc.
5
Revision D, November 7, 2016
840004I-01 Datasheet
Table 5C. AC Characteristics, VDD = VDDO = 2.5V ± 5%, TA = -40°C to 85°C
Parameter
Symbol
fout
Output Frequency
tsk(o)
Output Skew: NOTE 1, 2
tjit(Ø)
tR / tF
odc
RMS Phase Jitter (Random);
NOTE 3
Output Rise/Fall Time
Output Duty Cycle
Test Conditions
Minimum
Typical
Maximum
Units
F_SEL[1:0] = 00
140
156.25
175
MHz
F_SEL[1:0] = 01 or 11
112
125
140
MHz
F_SEL[1:0] = 10
56
62.5
70
MHz
60
MHz
156.25MHz, Integration Range:
1.875MHz – 20MHz
0.50
ps
125MHz, Integration Range:
1.875MHz – 20MHz
0.60
ps
62.5MHz, Integration Range:
1.875MHz – 20MHz
0.51
ps
20% to 80%
250
750
ps
F_SEL[1:0] = 00, 01 or 11
42
58
%
F_SEL[1:0] = 10
49
51
%
NOTE: Electrical parameters are guaranteed over the specified ambient operating temperature range, which is established when the
device is mounted in a test socket with maintained transverse airflow greater than 500 lfpm. The device will meet specifications after
thermal equilibrium has been reached under these conditions.
NOTE 1: Defined as skew between outputs at the same supply voltage and with equal load conditions. Measured at VDDO/2.
NOTE 2: This parameter is defined in accordance with JEDEC Standard 65.
NOTE 3: Please refer to the Phase Noise Plot.
©2016 Integrated Device Technology, Inc.
6
Revision D, November 7, 2016
840004I-01 Datasheet
?
Typical Phase Noise at 62.5MHz (3.3V)
10Gb Ethernet Filter
Raw Phase Noise Data
?
?
Noise Power dBc
Hz
62.5MHz
RMS Phase Jitter (Random)
1.875MHz to 20MHz = 0.55ps (typical)
Phase Noise Result by adding a
10Gb Ethernet filter to raw data
Offset Frequency (Hz)
?
Typical Phase Noise at 62.5MHz (2.5V)
10Gb Ethernet Filter
?
Noise Power dBc
Hz
62.5MHz
RMS Phase Jitter (Random)
1.875MHz to 20MHz = 0.53ps (typical)
?
Raw Phase Noise Data
Phase Noise Result by adding a
10Gb Ethernet filter to raw data
Offset Frequency (Hz)
©2016 Integrated Device Technology, Inc.
7
Revision D, November 7, 2016
840004I-01 Datasheet
?
Typical Phase Noise at 125MHz (3.3V)
10Gb Ethernet Filter
Raw Phase Noise Data
?
?
Noise Power dBc
Hz
125MHz
RMS Phase Jitter (Random)
1.875MHz to 20MHz = 0.65ps (typical)
Phase Noise Result by adding a
10Gb Ethernet filter to raw data
Offset Frequency (Hz)
?
Typical Phase Noise at 125MHz (2.5V)
10Gb Ethernet Filter
Raw Phase Noise Data
?
?
Noise Power dBc
Hz
125MHz
RMS Phase Jitter (Random)
1.875MHz to 20MHz = 0.60ps (typical)
Phase Noise Result by adding a
10Gb Ethernet filter to raw data
Offset Frequency (Hz)
©2016 Integrated Device Technology, Inc.
8
Revision D, November 7, 2016
840004I-01 Datasheet
?
Typical Phase Noise at 156.25MHz (3.3V)
10Gb Ethernet Filter
Raw Phase Noise Data
?
?
Noise Power dBc
Hz
156.25MHz
RMS Phase Jitter (Random)
1.875MHz to 20MHz = 0.52ps (typical)
Phase Noise Result by adding a
10Gb Ethernet filter to raw data
Offset Frequency (Hz)
?
Typical Phase Noise at 156.25MHz (2.5V)
10Gb Ethernet Filter
Raw Phase Noise Data
?
?
Noise Power dBc
Hz
156.25MHz
RMS Phase Jitter (Random)
1.875MHz to 20MHz = 0.50ps (typical)
Phase Noise Result by adding a
10Gb Ethernet filter to raw data
Offset Frequency (Hz)
©2016 Integrated Device Technology, Inc.
9
Revision D, November 7, 2016
840004I-01 Datasheet
Parameter Measurement Information
2.05V±5
1.65V±5
1.25V±5
1.65V±5
2.05V±5
SCOPE
VDD,
VDDO
SCOPE
VDD
VDDA
VDDO
Qx
Qx
VDDA
GND
GND
-1.65V±5
-1.25V±5
3.3V Core/3.3V LVCMOS Output Load AC Test Circuit
3.3V Core/2.5V LVCMOS Output Load AC Test Circuit
1.25V±5
Phase Noise Plot
Noise Power
1.25V±5
SCOPE
VDD,
VDDO
VDDA
Qx
Phase Noise Mask
GND
f1
Offset Frequency
f2
RMS Jitter = Area Under the Masked Phase Noise Plot
-1.25V±5
2.5V Core/2.5V LVCMOS Output Load AC Test Circuit
RMS Phase Jitter
V
80%
DDO
Qx
Q0:Q3
V
DDO
Qy
80%
2
20%
20%
tR
tF
2
tsk(o)
Output Skew
©2016 Integrated Device Technology, Inc.
Output Rise/Fall Time
10
Revision D, November 7, 2016
840004I-01 Datasheet
Parameter Measurement Information, continued
V
DDO
2
Q0:Q3
t PW
t
odc =
PERIOD
t PW
x 100%
t PERIOD
Output Duty Cycle Pulse Width/Period
©2016 Integrated Device Technology, Inc.
11
Revision D, November 7, 2016
840004I-01 Datasheet
Application Information
Recommendations for Unused Input and Output Pins
Inputs:
Outputs:
Crystal Inputs
LVCMOS Outputs
For applications not requiring the use of the crystal oscillator input,
both XTAL_IN and XTAL_OUT can be left floating. Though not
required, but for additional protection, a 1k resistor can be tied from
XTAL_IN to ground.
All unused LVCMOS outputs can be left floating. We recommend that
there is no trace attached.
REF_CLK Input
For applications not requiring the use of the reference clock, it can be
left floating. Though not required, but for additional protection, a 1k
resistor can be tied from the REF_CLK to ground.
LVCMOS Control Pins
All control pins have internal pull-downs; additional resistance is not
required but can be added for additional protection. A 1k resistor
can be used.
Power Supply Filtering Technique
As in any high speed analog circuitry, the power supply pins are
vulnerable to random noise. To achieve optimum jitter perfor- mance,
power supply isolation is required. The 840004I-01 provides
separate power supplies to isolate any high switching noise from the
outputs to the internal PLL. VDD, VDDA and VDDO should be
individually connected to the power supply plane through vias, and
0.01µF bypass capacitors should be used for each pin. Figure 1
illustrates this for a generic VDD pin and also shows that VDDA
requires that an additional 10 resistor along with a 10F bypass
capacitor be connected to the VDDA pin.
©2016 Integrated Device Technology, Inc.
3.3V
VDD
.01µF
10Ω
.01µF
10µF
VDDA
Figure 1. Power Supply Filtering
12
Revision D, November 7, 2016
840004I-01 Datasheet
Crystal Input Interface
The 840004I-01 has been characterized with 18pF parallel resonant
crystals. The capacitor values shown in Figure 2 below were
determined using a 25MHz, 18pF parallel resonant crystal and were
chosen to minimize the ppm error.
XTAL_IN
C1
22pF
X1
18pF Parallel Crystal
XTAL_OUT
C2
22pF
Figure 2. Crystal Input Interface
LVCMOS to XTAL Interface
The XTAL_IN input can accept a single-ended LVCMOS signal
through an AC coupling capacitor. A general interface diagram is
shown in Figure 3. The XTAL_OUT pin can be left floating. The input
edge rate can be as slow as 10ns. For LVCMOS inputs, it is
recommended that the amplitude be reduced from full swing to half
swing in order to prevent signal interference with the power rail and
to reduce noise. This configuration requires that the output
VCC
impedance of the driver (Ro) plus the series resistance (Rs) equals
the transmission line impedance. In addition, matched termination at
the crystal input will attenuate the signal in half. This can be done in
one of two ways. First, R1 and R2 in parallel should equal the
transmission line impedance. For most 50 applications, R1 and R2
can be 100. This can also be accomplished by removing R1 and
making R2 50.
VCC
R1
Ro
Rs
0.1µf
50Ω
XTAL_IN
Zo = Ro + Rs
R2
XTAL_OUT
Figure 3. General Diagram for LVCMOS Driver to XTAL Input Interface
©2016 Integrated Device Technology, Inc.
13
Revision D, November 7, 2016
840004I-01 Datasheet
Schematic Example
Figure 4 shows a schematic example of the 840004I-01. An example
of LVCMOS termination is shown in this schematic. Additional
LVCMOS termination approaches are shown in the LVCMOS
Termination Application Note. In this example, an 18pF parallel
resonant 25MHz crystal is used. The C1= 22pF and
C2 = 22pF
are recommended for frequency accuracy. For different board
layouts, the C1 and C2 may be slightly adjusted for optimizing
frequency accuracy. 1k pullup or pulldown resistors can be used for
the logic control input pins.
Logic Control Input Examples
Set Logic
Input to
'1'
VDD
Set Logic
Input to
'0'
VDD
RU1
1K
VDD=3.3V
VDDO=3.3V
RU2
Not Install
To Logic
Input
pins
R3
36
RD1
Not Install
RD2
1K
U1
VDDO
VDD
VDD
VDDA
R2
10
Zo = 50 Ohm
To Logic
Input
pins
C3
10uF
VDD
C4
0.01u
1
2
3
4
5
6
7
8
9
10
F_SEL0
nc
nXTAL_SEL
REF_CLK
OE
MR
nPLL_SEL
VDDA
nc
VDD
F_SEL1
GND
Q0
Q1
VDDO
Q2
Q3
GND
XTAL_IN
XTAL_OUT
LVCMOS
20
19
18
17
16
15
14
13
12
11
C6
0.1u
VDD
R5
100
Zo = 50 Ohm
C5
0.1u
840004i_01
XTAL_OUT
C2
22pF
R4
100
LVCMOS
X1
XTAL_IN
If not using the crystal input, it can be left floating.
For additional protection the XTAL_IN pin can be
tied to ground.
C1
22pF
Optional Termination
Unused outputs can be left floating. There should be
no trace attached to unused outputs. Device
characterized and specification limits set with all
outputs terminated.
Figure 4. P.C. 840004I-01 Schematic Example
©2016 Integrated Device Technology, Inc.
14
Revision D, November 7, 2016
840004I-01 Datasheet
Reliability Information
Table 6. JA vs. Air Flow Table for a 20 Lead TSSOP
JA by Velocity
Linear Feet per Minute
0
200
500
Single-Layer PCB, JEDEC Standard Test Boards
114.5°C/W
98.0°C/W
88.0°C/W
Multi-Layer PCB, JEDEC Standard Test Boards
73.2°C/W
66.6°C/W
63.5°C/W
NOTE: Most modern PCB designs use multi-layered boards. The data in the second row pertains to most designs.
Transistor Count
The transistor count for 840004I-01: 3796
Package Outline and Package Dimensions
Package Outline - G Suffix for 20 Lead TSSOP
Table 7. Package Dimensions for 20 Lead TSSOP
All Dimensions in Millimeters
Symbol
Minimum
Maximum
N
20
A
1.20
A1
0.05
0.15
A2
0.80
1.05
b
0.19
0.30
c
0.09
0.20
D
6.40
6.60
E
6.40 Basic
E1
4.30
4.50
e
0.65 Basic
L
0.45
0.75
0°
8°
aaa
0.10
Reference Document: JEDEC Publication 95, MO-153
©2016 Integrated Device Technology, Inc.
15
Revision D, November 7, 2016
840004I-01 Datasheet
Ordering Information
Table 8. Ordering Information
Part/Order Number
Marking
Package
Shipping Packaging
Temperature
840004BGI-01LF
ICS0004BI01L
20 Lead “Lead-Free” TSSOP
Tube
-40°C to 85°C
840004BGI-01LFT
ICS0004BI01L
20 Lead “Lead-Free” TSSOP
Tape & Reel
-40°C to 85°C
NOTE: Parts that are ordered with an "LF" suffix to the part number are the Pb-Free configuration and are RoHS compliant.
©2016 Integrated Device Technology, Inc.
16
Revision D, November 7, 2016
Revision History Sheet
Rev
A
B
C
C
C
D
Table
Page
T8
15
T5A - T5B
4-5
Description of Change
Date
Ordering Information Table - corrected standard marking and added lead-free
marking.
10/22/07
AC Characteristics Tables - revised Test Conditions for Output Duty Cycle.
Updated format throughout datasheet.
10/30/08
Changed from ICS840004AGI-01 to ICS840004BGI-01 throughout.
AC Characteristics - Changed Output Rise/Fall Time and Output Duty Cycle.
AC Characteristics - Changed Output Rise/Fall Time and Output Duty Cycle.
2/9/09
T5A - T5B
T5C
5
6
T8
16
Ordering Information - removed leaded devices.
Updated data sheet format.
4/2/15
1
Product Discontinuation Notice - Last time buy expires November 2, 2016.
PDN# CQ-15-05.
11/4/15
Obsolete datasheet per PDN# CQ-15-05.
Updated datasheet header/footer.
11/7/16
Corporate Headquarters
Sales
Tech Support
6024 Silver Creek Valley Road
San Jose, CA 95138 USA
www.IDT.com
1-800-345-7015 or 408-284-8200
Fax: 408-284-2775
www.IDT.com/go/sales
www.idt.com/go/support
DISCLAIMER Integrated Device Technology, Inc. (IDT) reserves the right to modify the products and/or specifications described herein at any time, without notice, at IDT's sole discretion. Performance specifications
and operating parameters of the described products are determined in an independent state and are not guaranteed to perform the same way when installed in customer products. The information contained herein
is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT's products for any particular purpose, an implied warranty of merchantability,
or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.
IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably
expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.
Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the property of
IDT or their respective third party owners.
For datasheet type definitions and a glossary of common terms, visit www.idt.com/go/glossary.
Copyright ©2016 Integrated Device Technology, Inc. All rights reserved.
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.