7-Output 1.5V PCIe Gen1-2-3 Fanout Buffer
with Zo=100ohms
9DBU0741
DATASHEET
Description
Features/Benefits
The 9DBU0741 is a member of IDT's 1.5V Ultra-Low-Power
(ULP) PCIe family. It has integrated terminations for direct
connection to 100 transmission lines. The device has 7
output enables for clock management, and 3 selectable
SMBus addresses.
• Integrated terminations; save 28 resistors compared to
•
•
Recommended Application
•
1.5V PCIe Gen1-2-3 Fanout Buffer (FOB)
•
•
Output Features
• 7 – 1–167MHz Low-Power (LP) HCSL DIF pairs with
Zo=100
•
Key Specifications
•
•
•
•
DIF additive cycle-to-cycle jitter < 5ps
DIF output-to-output skew < 60ps
DIF additive phase jitter is < 300fs rms for PCIe Gen3
DIF additive phase jitter < 350s rms for SGMII
•
•
•
•
standard HCSL outputs
36mW typical power consumption; eliminates thermal
concerns
Outputs can optionally be supplied from any voltage
between 1.05V and 1.5V; maximum power savings
Spread Spectrum (SS) compatible; allows SS for EMI
reduction
OE# pins for each output; support DIF power management
HCSL-compatible differential input; can be driven by
common clock sources
SMBus-selectable features; optimize signal integrity to
application
• slew rate for each output
• differential output amplitude
Device contains default configuration; SMBus interface not
required for device operation
Selectable SMBus addresses; multiple devices can easily
share an SMBus segment
3.3V tolerant SMBus interface works with legacy controllers
5 × 5 mm 40-VFQFPN package; minimal board space
Block Diagram
vOE(6:0)#
7
DIF6
CLK_IN
DIF5
CLK_IN#
DIF4
DIF3
vSADR
^CKPWRGD_PD#
SDATA_3.3
DIF2
CONTROL
LOGIC
DIF1
SCLK_3.3
9DBU0741 MARCH 8, 2017
DIF0
1
©2017 Integrated Device Technology, Inc.
9DBU0741 DATASHEET
VDD1.5
VDDIO
DIF4
DIF4#
vOE4#
DIF5
DIF5#
vOE5#
VDDIO
^CKPWRGD_PD#
Pin Configuration
40 39 38 37 36 35 34 33 32 31
vSADR_tri 1
30 NC
vOE6# 2
29 vOE3#
DIF6 3
28 DIF3#
DIF6# 4
27 DIF3
9DBU0741
epad is GND
VDDR1.5 5
CLK_IN 6
26 VDDIO
25 VDDO1.5
CLK_IN# 7
24 vOE2#
GNDDIG 8
23 DIF2#
SCLK_3.3 9
22 DIF2
SDATA_3.3 10
21 vOE1#
NC
DIF1#
DIF1
VDDIO
DIF0#
VDD1.5
DIF0
vOE0#
VDDIO
VDDDIG1.5
11 12 13 14 15 16 17 18 19 20
40-VFQFPN
^ prefix indicates internal Pull-Up Resistor
v prefix indicates Internal Pull-Dow n Resistor
5mm x 5mm 0.4mm pin pitch
SMBus Address Selection Table
State of SADR on first application of
CKPWRGD_PD#
SADR
0
M
1
Address
1101011
1101100
1101101
+
Read/Write bit
x
x
x
Power Management Table
CKPWRGD_PD#
CLK_IN
0
1
1
1
X
Running
Running
Running
SMBus
OEx bit
X
0
1
1
OEx# Pin
X
X
0
1
DIFx
True O/P Comp. O/P
Low
Low
Low
Low
Running
Running
Low
Low
Power Connections
Pin Number
VDD
VDDIO
5
41
11
16,25,31
GND
8
12,17,26,32,
39
41
Description
Input
receiver
analog
Digital power
DIF outputs,
Logic
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
2
MARCH 8, 2017
9DBU0741 DATASHEET
Pin Descriptions
PIN #
PIN NAME
1
vSADR_tri
2
vOE6#
3
4
DIF6
DIF6#
5
VDDR1.5
6
7
8
9
10
11
12
CLK_IN
CLK_IN#
GNDDIG
SCLK_3.3
SDATA_3.3
VDDDIG1.5
VDDIO
13
vOE0#
14
15
16
17
18
19
20
DIF0
DIF0#
VDD1.5
VDDIO
DIF1
DIF1#
NC
21
vOE1#
22
23
DIF2
DIF2#
24
vOE2#
25
26
27
28
VDDO1.5
VDDIO
DIF3
DIF3#
29
vOE3#
30
31
32
33
34
NC
VDD1.5
VDDIO
DIF4
DIF4#
35
vOE4#
36
37
DIF5
DIF5#
38
vOE5#
39
VDDIO
40
^CKPWRGD_PD#
41
EPAD
MARCH 8, 2017
PIN
DESCRIPTION
Tri-level latch to select SMBus Address. It has an internal 120kohm pull down resistor.
LATCHE
See SMBus Address Selection Table.
D IN
Active low input for enabling output 6. This pin has an internal 120kohm pull-down.
IN
1 =disable outputs, 0 = enable outputs
OUT
Differential true clock output.
OUT
Differential complementary clock output.
1.5V power for differential input clock (receiver). This VDD should be treated as an
PWR
Analog power rail and filtered appropriately.
IN
True Input for differential reference clock.
IN
Complementary Input for differential reference clock.
GND
Ground pin for digital circuitry.
IN
Clock pin of SMBus circuitry, 3.3V tolerant.
I/O
Data pin for SMBus circuitry, 3.3V tolerant.
PWR
1.5V digital power (dirty power)
PWR
Power supply for differential outputs
Active low input for enabling output 0. This pin has an internal 120kohm pull-down.
IN
1 =disable outputs, 0 = enable outputs
OUT
Differential true clock output.
OUT
Differential complementary clock output.
PWR
Power supply, nominally 1.5V
PWR
Power supply for differential outputs
OUT
Differential true clock output.
OUT
Differential complementary clock output.
N/A
No connection.
Active low input for enabling output 1. This pin has an internal 120kohm pull-down.
IN
1 =disable outputs, 0 = enable outputs
OUT
Differential true clock output.
OUT
Differential complementary clock output.
Active low input for enabling output 2. This pin has an internal 120kohm pull-down.
IN
1 =disable outputs, 0 = enable outputs
PWR
Power supply for outputs, nominally 1.5V.
PWR
Power supply for differential outputs
OUT
Differential true clock output.
OUT
Differential complementary clock output.
Active low input for enabling output 3. This pin has an internal 120kohm pull-down.
IN
1 =disable outputs, 0 = enable outputs
N/A
No connection.
PWR
Power supply, nominally 1.5V
PWR
Power supply for differential outputs
OUT
Differential true clock output.
OUT
Differential complementary clock output.
Active low input for enabling output 4. This pin has an internal 120kohm pull-down.
IN
1 =disable outputs, 0 = enable outputs
OUT
Differential true clock output.
OUT
Differential complementary clock output.
Active low input for enabling output 5. This pin has an internal 120kohm pull-down.
IN
1 =disable outputs, 0 = enable outputs
PWR
Power supply for differential outputs
Input notifies device to sample latched inputs and start up on first high assertion. Low
IN
enters Power Down Mode, subsequent high assertions exit Power Down Mode. This pin
has internal 120kohm pull-up resistor.
GND
Connect paddle to ground.
3
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
9DBU0741 DATASHEET
Test Loads
Low-Power HCSL Differential Output Test Load
5 inches
Rs
Zo=100
2pF
Rs
2pF
Note: The device can drive transmission line lengths greater
than those allowed by the PCIe SIG
Driving LVDS
3.3V
Driving LVDS
Cc
R7a
R7b
R8a
R8b
Rs
Zo
Cc
Rs
Device
LVDS Clock
input
Driving LVDS inputs
Component
R7a, R7b
R8a, R8b
Cc
Vcm
Value
Receiver has Receiver does not
termination
have termination Note
10K ohm
140 ohm
5.6K ohm
75 ohm
0.1µF
0.1µF
1.2 volts
1.2 volts
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
4
MARCH 8, 2017
9DBU0741 DATASHEET
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the 9DBU0741. These ratings, which are standard
values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other
conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the
recommended operating temperature range.
PARAMETER
SYMBOL
CONDITIONS
Supply Voltage
Input Voltage
Input High Voltage, SMBus
Storage Temperature
Junction Temperature
Input ESD protection
VDDx
VIN
VIHSMB
Ts
Tj
ESD prot
Applies to VDD, VDDA and VDDIO
MIN
-0.5
-0.5
TYP
SMBus clock and data pins
-65
Human Body Model
MAX
2
VDD+0.5
3.3
150
125
2000
UNITS NOTES
V
V
V
°C
°C
V
1,2
1,
1
1
1
1
1
Guaranteed by design and characterization, not 100% tested in production.
2
Operation under these conditions is neither implied nor guaranteed.
3
Not to exceed 2.0V.
Electrical Characteristics–Clock Input Parameters
TA = TAMB, Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions
PARAMETER
Input Common Mode
Voltage - DIF_IN
Input Swing - DIF_IN
Input Slew Rate - DIF_IN
Input Leakage Current
Input Duty Cycle
Input Jitter - Cycle to Cycle
1
2
SYMBOL
CONDITIONS
MIN
TYP
VCOM
Common Mode Input Voltage
200
725
mV
1
VSWING
dv/dt
IIN
dtin
J DIFIn
Differential value
Measured differentially
VIN = VDD , VIN = GND
Measurement from differential waveform
Differential Measurement
300
0.4
-5
45
0
1450
8
5
55
150
mV
V/ns
µA
%
ps
1
1,2
50
MAX
UNITS NOTES
1
1
Guaranteed by design and characterization, not 100% tested in production.
Slew rate measured through +/-75mV window centered around differential zero.
MARCH 8, 2017
5
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
9DBU0741 DATASHEET
Electrical Characteristics–Input/Supply/Common Parameters–Normal Operating
Conditions
TA = TAMB; Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
Supply Voltage
Output Supply Voltage
Ambient Operating
Temperature
Input High Voltage
Input Mid Voltage
Input Low Voltage
VDDx
VDDIO
Supply voltage for core and analog
Low Voltage Supply LP-HCSL Outputs
Commercial range
Industrial range
Single-ended inputs, except SMBus
Single-ended tri-level inputs ('_tri' suffix)
Single-ended inputs, except SMBus
Single-ended inputs, VIN = GND, VIN = VDD
1.425
0.95
0
-40
0.75 VDD
0.4 VDD
-0.3
-5
1.5
1.05-1.5
25
25
1.575
1.575
70
85
VDD + 0.3
0.6 VDD
0.25 VDD
5
V
V
°C
°C
V
V
V
µA
Single-ended inputs
VIN = 0 V; Inputs with internal pull-up resistors
VIN = VDD; Inputs with internal pull-down resistors
-200
200
µA
1
167
7
5
2.7
6
MHz
nH
pF
pF
pF
2
1
1
1,5
1
1
ms
1,2
30
33
kHz
0
66
kHz
1
3
clocks
1,3
300
µs
1,3
5
5
0.6
3.3
0.4
2
2
3.3
1000
300
ns
ns
V
V
V
mA
V
ns
ns
400
kHz
6
Input Current
TAMB
VIH
VIM
VIL
IIN
IINP
Input Frequency
Pin Inductance
Fin
Lpin
CIN
Capacitance
CINDIF_IN
COUT
Clk Stabilization
TSTAB
OE# Latency
tLATOE#
Tdrive_PD#
tDRVPD
Tfall
Trise
SMBus Input Low Voltage
SMBus Input High Voltage
SMBus Output Low Voltage
SMBus Sink Current
Nominal Bus Voltage
SCLK/SDATA Rise Time
SCLK/SDATA Fall Time
SMBus Operating
Frequency
tF
tR
Logic Inputs, except DIF_IN
DIF_IN differential clock inputs
Output pin capacitance
From VDD Power-Up and after input clock
stabilization or de-assertion of PD# to 1st clock
Allowable Frequency for PCIe Applications
(Triangular Modulation)
Allowable Frequency for non-PCIe Applications
(Triangular Modulation)
DIF start after OE# assertion
DIF stop after OE# deassertion
DIF output enable after
PD# de-assertion
Fall time of single-ended control inputs
Rise time of single-ended control inputs
VILSMB
VIHSMB
VOLSMB
IPULLUP
VDDSMB
tRSMB
t FSMB
VDDSMB = 3.3V, see note 4 for VDDSMB < 3.3V
@ IPULLUP
@ VOL
Bus Voltage
(Max VIL - 0.15) to (Min VIH + 0.15)
(Min VIH + 0.15) to (Max VIL - 0.15)
fMAXSMB
Maximum SMBus operating frequency
Input SS Modulation
Frequency PCIe
Input SS Modulation
Frequency non-PCIe
fMODINPCIe
fMODIN
1.5
1.5
2.1
4
1.425
UNITS NOTES
1
1
4
1
1
1
Guaranteed by design and characterization, not 100% tested in production.
Control input must be monotonic from 20% to 80% of input swing.
3
Time from deassertion until outputs are > 200 mV.
4
For VDDSMB < 3.3V, VIHSMB >= 0.8xVDDSMB.
5
DIF_IN input.
2
6
The differential input clock must be running for the SMBus to be active.
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
6
MARCH 8, 2017
9DBU0741 DATASHEET
Electrical Characteristics–DIF Low-Power HCSL Outputs
TA = TAMB; Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
Scope averaging on, fast setting
Scope averaging on, slow setting
Slew rate matching, Scope averaging on
1
0.7
Slew rate matching
dV/dt
dV/dt
ΔdV/dt
2.4
1.7
9
3.5
2.5
20
Voltage High
VHIGH
630
750
850
Slew rate
Voltage Low
VLOW
Statistical measurement on single-ended signal
using oscilloscope math function. (Scope
averaging on)
Max Voltage
Min Voltage
Vswing
Crossing Voltage (abs)
Crossing Voltage (var)
Vmax
Vmin
Vswing
Vcross_abs
Δ-Vcross
Measurement on single ended signal using
absolute value. (Scope averaging off)
Scope averaging off
Scope averaging off
Scope averaging off
MAX UNITS NOTES
V/ns
V/ns
%
1,2,3
1,2,3
1,2,4
7
mV
-150
26
150
763
22
1448
390
11
1150
-300
300
250
550
140
7
mV
mV
mV
mV
7
7
1,2
1,5
1,6
1
Guaranteed by design and characterization, not 100% tested in production.
Measured from differential waveform
2
3
Slew rate is measured through the Vswing voltage range centered around differential 0V. This results in a +/-150mV window around
differential 0V.
4
Matching applies to rising edge rate for Clock and falling edge rate for Clock#. It is measured using a +/-75mV window centered on
the average cross point where Clock rising meets Clock# falling. The median cross point is used to calculate the voltage thresholds the
oscilloscope is to use for the edge rate calculations.
5
Vcross is defined as voltage where Clock = Clock# measured on a component test board and only applies to the differential rising
edge (i.e. Clock rising and Clock# falling).
6
The total variation of all Vcross measurements in any particular system. Note that this is a subset of Vcross_min/max (Vcross
absolute) allowed. The intent is to limit Vcross induced modulation by setting Δ-Vcross to be smaller than Vcross absolute.
7
At default SMBus settings.
Electrical Characteristics–Current Consumption
TA = TAMB; Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions
PARAMETER
Operating Supply Current
Powerdown Current
1
2
SYMBOL
CONDITIONS
IDDA
VDDO1.5+VDDR, @100MHz
MIN
IDDx
VDDx, All outputs active @100MHz
IDDIO
IDDAPD
IDDxPD
IDDIOPD
VDDIO, All outputs active @100MHz
VDDO1.5+VDDR, CKPWRGD_PD# = 0
VDDx, CKPWRGD_PD# = 0
VDDIO, CKPWRGD_PD# = 0
TYP
MAX
UNITS
2.1
3
mA
3.6
5
mA
25
0.4
0.3
0.001
31
1
0.6
0.1
mA
mA
mA
mA
NOTES
2
2
2
Guaranteed by design and characterization, not 100% tested in production.
Input clock stopped.
MARCH 8, 2017
7
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
9DBU0741 DATASHEET
Electrical Characteristics–Output Duty Cycle, Jitter, Skew and PLL Characteristics
TA = TAMB; Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
NOTES
Duty Cycle Distortion
Skew, Input to Output
Skew, Output to Output
Jitter, Cycle to cycle
tDCD
tpdBYP
tsk3
Measured differentially, @100MHz
VT = 50%
VT = 50%
-1
2400
-0.2
2862
30
0.5
3700
60
%
ps
ps
1,3
1
1,4
tjcy c-cy c
Additive Jitter
0.1
5
ps
1,2
1
Guaranteed by design and characterization, not 100% tested in production.
2
Measured from differential waveform.
3
Duty cycle distortion is the difference in duty cycle between the output and the input clock.
4
All outputs at default slew rate.
Electrical Characteristics–Phase Jitter Parameters
TA = TAMB; Supply Voltages per normal operation conditions, See Test Loads for Loading Conditions
PARAMETER
SYMBOL
CONDITIONS
tjphPCIeG1
PCIe Gen 1
PCIe Gen 2 Lo Band
10kHz < f < 1.5MHz
PCIe Gen 2 High Band
1.5MHz < f < Nyquist (50MHz)
PCIe Gen 3
(2-4MHz or 2-5MHz, CDR = 10MHz)
tjphPCIeG2
Additive Phase Jitter
tjphPCIeG3
MIN
INDUSTRY
LIMIT
UNITS
TYP
MAX
0.1
5
N/A
0.1
0.4
N/A
0.1
0.7
N/A
0.1
0.3
N/A
ps (p-p)
ps
(rms)
ps
(rms)
ps
(rms)
Notes
1,2,3,5
1,2,3,4,
5
1,2,3,4
1,2,3,4
tjphSGMIIM0
125MHz, 1.5MHz to 10MHz, -20dB/decade
rollover < 1.5MHz, -40db/decade rolloff > 10MHz
200
250
N/A
fs
(rms)
1,6
tjphSGMIIM1
125MHz, 12kHz to 20MHz, -20dB/decade rollover
< 1.5MHz, -40db/decade rolloff > 10MHz
313
350
N/A
fs
(rms)
1,6
1
Guaranteed by design and characterization, not 100% tested in production.
See http://www.pcisig.com for complete specs.
2
3
Sample size of at least 100K cycles. This figures extrapolates to 108ps pk-pk @ 1M cycles for a BER of 1-12.
4
For RMS figures, additive jitter is calculated by solving the following equation: Additive jitter = SQRT[(total jitter)^2 - (input jitter)^2].
Driven by 9FGV0831 or equivalent.
Rohde & Schwarz SMA100.
5
6
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
8
MARCH 8, 2017
9DBU0741 DATASHEET
Additive Phase Jitter Plot: 125M (12kHz to 20MHz)
RMS additive jitter: 313fs
MARCH 8, 2017
9
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
9DBU0741 DATASHEET
General SMBus Serial Interface Information
How to Write
How to Read
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Controller (host) sends a start bit
Controller (host) sends the write address
IDT clock will acknowledge
Controller (host) sends the beginning byte location = N
IDT clock will acknowledge
Controller (host) sends the byte count = X
IDT clock will acknowledge
Controller (host) starts sending Byte N through Byte
N+X-1
IDT clock will acknowledge each byte one at a time
Controller (host) sends a stop bit
•
•
•
Controller (host) will send a start bit
Controller (host) sends the write address
IDT clock will acknowledge
Controller (host) sends the beginning byte location = N
IDT clock will acknowledge
Controller (host) will send a separate start bit
Controller (host) sends the read address
IDT clock will acknowledge
IDT clock will send the data byte count = X
IDT clock sends Byte N+X-1
IDT clock sends Byte 0 through Byte X (if X(H) was
written to Byte 8)
Controller (host) will need to acknowledge each byte
Controller (host) will send a not acknowledge bit
Controller (host) will send a stop bit
Index Block Write Operation
Controller (Host)
T
Index Block Read Operation
IDT (Slave/Receiver)
Controller (Host)
starT bit
T
Slave Address
WR
IDT (Slave/Receiver)
starT bit
Slave Address
WRite
WR
WRite
ACK
ACK
Beginning Byte = N
Beginning Byte = N
ACK
ACK
Data Byte Count = X
RT
ACK
Slave Address
Beginning Byte N
RD
ACK
O
O
ACK
O
Data Byte Count=X
O
ACK
O
Beginning Byte N
Byte N + X - 1
ACK
ACK
P
ReaD
stoP bit
X Byte
X Byte
O
Repeat starT
O
O
O
O
O
O
Note: SMBus Address is Latched on SADR pin.
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
Byte N + X - 1
10
N
Not acknowledge
P
stoP bit
MARCH 8, 2017
9DBU0741 DATASHEET
SMBus Table: Output Enable Register 1
Byte 0
Name
Control Function
Type
0
DIF OE5
Output Enable
RW
Low/Low
Bit 7
DIF OE4
Output Enable
RW
Low/Low
Bit 6
Reserved
Bit 5
DIF OE3
Output Enable
RW
Low/Low
Bit 4
DIF
OE2
Output
Enable
RW
Low/Low
Bit 3
DIF OE1
Output Enable
RW
Low/Low
Bit 2
Reserved
Bit 1
DIF OE0
Output Enable
RW
Low/Low
Bit 0
1. A low on these bits will override the OE# pin and force the differential output Low/Low
SMBus Table: PLL Operating Mode and Output Amplitude Control Register
Byte 1
Name
Control Function
Type
0
Reserved
Bit 7
Reserved
Bit 6
DIF OE6
Output Enable
RW
Low/Low
Bit 5
Reserved
Bit 4
Reserved
Bit 3
Reserved
Bit 2
AMPLITUDE 1
RW
00 = 0.55V
Bit 1
Controls Output Amplitude
AMPLITUDE 0
RW
10 = 0.7V
Bit 0
1. A low on the DIF OE bit will override the OE# pin and force the differential output Low/Low
SMBus Table: DIF Slew Rate Control Register
Byte 2
Name
Control Function
Type
SLEWRATESEL DIF5
Adjust Slew Rate of DIF5
RW
Bit 7
SLEWRATESEL DIF4
Adjust Slew Rate of DIF4
RW
Bit 6
Reserved
Bit 5
SLEWRATESEL DIF3
Adjust Slew Rate of DIF3
RW
Bit 4
SLEWRATESEL DIF2
Adjust Slew Rate of DIF2
RW
Bit 3
SLEWRATESEL DIF1
Adjust Slew Rate of DIF1
RW
Bit 2
Reserved
Bit 1
SLEWRATESEL DIF0
Adjust Slew Rate of DIF0
RW
Bit 0
Note: See "DIF 0.7V Low-Power HCSL Outputs" table for slew rates.
SMBus Table: DIF Slew Rate Control Register
Byte 3
Name
Control Function
Type
Reserved
Bit 7
Reserved
Bit 6
Reserved
Bit 5
Reserved
Bit 4
Reserved
Bit 3
Reserved
Bit 2
Reserved
Bit 1
SLEWRATESEL DIF6
Adjust Slew Rate of DIF6
RW
Bit 0
Note: See "DIF 0.7V Low-Power HCSL Outputs" table for slew rates.
1
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
1
Enabled
01= 0.65V
11 = 0.8V
0
Slow Setting
Slow Setting
1
Fast Setting
Fast Setting
Slow Setting
Slow Setting
Slow Setting
Fast Setting
Fast Setting
Fast Setting
Slow Setting
Fast Setting
0
1
Slow Setting
Fast Setting
Default
1
1
1
1
1
1
1
1
Default
0
1
1
0
1
1
1
0
Default
1
1
1
1
1
1
1
1
Default
1
1
0
0
0
1
1
1
Byte 4 is Reserved and reads back 'hFF
MARCH 8, 2017
11
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
9DBU0741 DATASHEET
SMBus Table: Revision and Vendor ID Register
Byte 5
Name
Control Function
RID3
Bit 7
RID2
Bit 6
Revision ID
RID1
Bit 5
RID0
Bit 4
VID3
Bit 3
VID2
Bit 2
VENDOR ID
VID1
Bit 1
VID0
Bit 0
Type
R
R
R
R
R
R
R
R
SMBus Table: Device Type/Device ID
Byte 6
Name
Device Type1
Bit 7
Device Type0
Bit 6
Device ID5
Bit 5
Device ID4
Bit 4
Device ID3
Bit 3
Device ID2
Bit 2
Device ID1
Bit 1
Device ID0
Bit 0
Type
R
R
R
R
R
R
R
R
SMBus Table: Byte Count Register
Byte 7
Name
Bit 7
Bit 6
Bit 5
BC4
Bit 4
BC3
Bit 3
BC2
Bit 2
BC1
Bit 1
BC0
Bit 0
Control Function
Device Type
Device ID
Control Function
Reserved
Reserved
Reserved
Byte Count Programming
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
12
Type
RW
RW
RW
RW
RW
0
1
A rev = 0000
0001 = IDT
0
1
00 = FGx, 01 = DBx,
10 = DMx, 11= DBx w/oPLL
000111 binary or 07 hex
0
Default
0
0
0
0
0
0
0
1
Default
1
1
0
0
0
1
1
1
1
Default
0
0
0
0
Writing to this register will configure how
1
many bytes will be read back, default is
0
= 8 bytes.
0
0
MARCH 8, 2017
9DBU0741 DATASHEET
Marking Diagrams
ICS
DBU0741AL
YYWW
COO
LOT
ICS
BU0741AIL
YYWW
COO
LOT
Notes:
1. “LOT” is the lot sequence number.
2. “COO” denotes country of origin.
3. YYWW is the last two digits of the year and week that the part was assembled.
4. Line 2: truncated part number
5. “L” denotes RoHS compliant package.
6. “I” denotes industrial temperature range device.
Thermal Characteristics
PARAMETER
SYMBOL
Thermal Resistance
θJC
θJb
θJA0
θJA1
θJA3
θJA5
TYP
VALUE
Junction to Case
42
Junction to Base
2.4
Junction to Air, still air
39
NDG40
Junction to Air, 1 m/s air flow
33
Junction to Air, 3 m/s air flow
28
Junction to Air, 5 m/s air flow
27
CONDITIONS
PKG
UNITS NOTES
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
1
1
1
1
1
1
1
ePad soldered to board
MARCH 8, 2017
13
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
9DBU0741 DATASHEET
Package Outline and Package Dimensions (NDG40)
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
14
MARCH 8, 2017
9DBU0741 DATASHEET
Package Outline and Package Dimensions (NDG40), cont.
MARCH 8, 2017
15
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
9DBU0741 DATASHEET
Ordering Information
Part / Order Number Shipping Packaging
9DBU0741AKLF
Trays
9DBU0741AKLFT
Tape and Reel
9DBU0741AKILF
Trays
9DBU0741AKILFT
Tape and Reel
Package
40-pin VFQFPN
40-pin VFQFPN
40-pin VFQFPN
40-pin VFQFPN
Temperature
0 to +70° C
0 to +70° C
-40 to +85° C
-40 to +85° C
“LF” suffix to the part number are the Pb-Free configuration and are RoHS compliant.
“A” is the device revision designator (will not correlate with the datasheet revision).
Revision History
Rev.
A
B
C
D
Initiator Issue Date Description
RDW
7/15/2014 Final update and release - front page and electrical tables.
Updated SMBus Input High/Low parameters conditions, MAX values,
RDW
9/19/2014
and footnotes.
1. Updated pin out and pin descriptions to show ePad on package
connected to ground.
RDW
4/14/2015 2. Minor updates to front page text for family consistency.
3. Updated Clock Input Parameters table to be consistent with PCIe
Vswing parameter.
1. Updated pin 25 from VDDA1.5 to VDDO1.5 to clearly indicate that
this part has no PLL.
2. Removed "Bypass Mode" reference in "Output Duty Cycle..." and
RDW
3/8/2017 "Phase Jitter Parameters" tables; update note 3 under Output Duty
Cycle table.
3. Changed VDDA to VDDO1.5 in Current Consumption table.
4. Updated Additive Phase Jitter conditions for PCIe Gen3.
7-OUTPUT 1.5V PCIE GEN1-2-3 FANOUT BUFFER WITH ZO=100OHMS
16
Page #
Various
6
1-5
2,3,7,8
MARCH 8, 2017
Corporate Headquarters
Sales
Tech Support
6024 Silver Creek Valley Road
San Jose, CA 95138 USA
www.idt.com
1-800-345-7015 or 408-284-8200
Fax: 408-284-2775
www.idt.com/go/sales
www.idt.com/go/support
DISCLAIMER Integrated Device Technology, Inc. (IDT) and its affiliated companies (herein referred to as “IDT”) reserve the right to modify the products and/or specifications described herein at any time, without
notice, at IDT’s sole discretion. Performance specifications and operating parameters of the described products are determined in an independent state and are not guaranteed to perform the same way when installed
in customer products. The information contained herein is provided without representation or warranty of any kind, whether express or implied, including, but not limited to, the suitability of IDT's products for any
particular purpose, an implied warranty of merchantability, or non-infringement of the intellectual property rights of others. This document is presented only as a guide and does not convey any license under intellectual property rights of IDT or any third parties.
IDT's products are not intended for use in applications involving extreme environmental conditions or in life support systems or similar devices where the failure or malfunction of an IDT product can be reasonably
expected to significantly affect the health or safety of users. Anyone using an IDT product in such a manner does so at their own risk, absent an express, written agreement by IDT.
Integrated Device Technology, IDT and the IDT logo are trademarks or registered trademarks of IDT and its subsidiaries in the United States and other countries. Other trademarks used herein are the property of
IDT or their respective third party owners. For datasheet type definitions and a glossary of common terms, visit www.idt.com/go/glossary. Integrated Device Technology, Inc.. All rights reserved.
9DBU0741 MARCH 8, 2017
17
©2017 Integrated Device Technology, Inc.
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.