DATASHEET
EL5172
FN7311
Rev.12.00
Jul 30, 2020
250MHz Differential Line Receiver
The EL5172 is a single high bandwidth amplifier designed to
extract the difference signal from noisy environments. It is
primarily targeted for applications such as receiving signals
from twisted-pair lines or any application where common
mode noise injection is likely to occur.
The EL5172 is stable for a gain of one and requires two
external resistors to set the voltage gain.
The output common mode level is set by the reference pin
(VREF), which has a -3dB bandwidth of over 120MHz.
Generally, this pin is grounded but it can be tied to any
voltage reference.
The output can deliver a maximum of ±60mA and is
short-circuit protected to withstand a temporary overload
condition.
The EL5172 is available in the 8 Ld SOIC and 8 Ld MSOP
packages. It is specified for operation across the full -40°C to
+85°C temperature range.
Related Literature
Features
• Differential input range ±2.3V
• 250MHz 3dB bandwidth
• 800V/µs slew rate
• 60mA maximum output current
• Single 5V or dual ±5V supplies
• Low power - 5mA to 6mA
• Pb-free available (RoHS compliant)
Applications
• Twisted-pair receivers
• Differential line receivers
• VGA over twisted-pair
• ADSL/HDSL receivers
• Differential to single-ended amplification
• Reception of analog signals in a noisy environment
For a full list of related documents, visit our website:
• EL5172 device page
FN7311 Rev.12.00
Jul 30, 2020
Page 1 of 16
EL5172
Ordering Information
PART
NUMBER
PART
MARKING
TAPE AND REEL
(Units)
PACKAGE
(RoHS Compliant)
PKG.
DWG. #
EL5172ISZ
5172ISZ
-
8 Ld SOIC (150 mil)
M8.15E
EL5172ISZ-T7
5172ISZ
1k
8 Ld SOIC (150 mil)
M8.15E
EL5172ISZ-T7A
5172ISZ
250
8 Ld SOIC (150 mil)
M8.15E
EL5172ISZ-T13
5172ISZ
2.5k
8 Ld SOIC (150 mil)
M8.15E
EL5172IYZ
BAAWA
-
8 Ld MSOP (3.0mm)
M8.118A
EL5172IYZ-T7
BAAWA
1.5k
8 Ld MSOP (3.0mm)
M8.118A
EL5172IYZ-T13
BAAWA
2.5k
8 Ld MSOP (3.0mm)
M8.118A
NOTES:
1. See TB347 for details about reel specifications.
2. These Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100% matte tin
plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations). Pb-free
products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
3. For Moisture Sensitivity Level (MSL), see the EL5172 device page. For more information about MSL, see TB363.
FN7311 Rev.12.00
Jul 30, 2020
Page 2 of 16
EL5172
Pinout
(8 LD SOIC, MSOP)
TOP VIEW
8 OUT
FB 1
IN+ 2
IN- 3
+
-
REF 4
7 VS6 VS+
5 EN
Pin Descriptions
PIN NUMBERS
PIN NAME
1
FB
Feedback input
2
IN+
Non-inverting input
3
IN-
Inverting input
4
REF
5
EN
Enabled when this pin is floating or the applied voltage VS+ - 1.5
6
VS+
Positive supply voltage
7
VS-
Negative supply voltage
8
OUT
Output voltage
FN7311 Rev.12.00
Jul 30, 2020
PIN FUNCTION
Sets the common mode output voltage level
Page 3 of 16
EL5172
Absolute Maximum Ratings (TA = +25°C)
Thermal Information
Supply Voltage (VS+ to VS-) . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V
Supply Voltage Rate-of-rise (dV/dT) . . . . . . . . . . . . . . . . . . . . 1V/µs
Input Voltage (IN+, IN- to VS+, VS-). . . . . . VS- - 0.3V to VS+ + 0.3V
Differential Input Voltage (IN+ to IN-) . . . . . . . . . . . . . . . . . . . . ±4.8V
Maximum Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . ±60mA
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +135°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . see TB493
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions can adversely impact product reliability and
result in failures not covered by warranty.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
PARAMETER
VS+ = +5V, VS- = -5V, TA = +25°C, VIN = 0V, RL = 500, RF = 0, RG = OPEN, CL = 2.7pF, Unless Otherwise
Specified.
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
AC PERFORMANCE
BW
-3dB Bandwidth
AV =1, CL = 2.7pF
250
MHz
AV =2, RF = 1000Ω, CL = 2.7pF
70
MHz
AV =10, RF = 1000Ω, CL = 2.7pF
10
MHz
25
MHz
BW
±0.1dB Bandwidth
AV =1, CL = 2.7pF
SR
Slew Rate
VOUT = 3VP-P, 20% to 80%
tSTL
Settling Time to 0.1%
VOUT = 2VP-P
tOVR
GBWP
550
800
1000
V/µs
10
ns
Output Overdrive Recovery Time
20
ns
Gain Bandwidth Product
100
MHz
VREFBW (-3dB) VREF -3dB Bandwidth
AV =1, CL = 2.7pF
120
MHz
VREFSR
VREF Slew Rate
VOUT = 2VP-P, 20% to 80%
600
V/µs
VN
Input Voltage Noise
at f = 11kHz
26
nV/Hz
IN
Input Current Noise
at f = 11kHz
2
pA/Hz
HD2
Second Harmonic Distortion
VOUT = 1VP-P, 5MHz
-66
dBc
VOUT = 2VP-P, 50MHz
-63
dBc
VOUT = 1VP-P, 5MHz
-84
dBc
VOUT = 2VP-P, 50MHz
-76
dBc
HD3
Third Harmonic Distortion
dG
Differential Gain at 3.58MHz
RL = 150ΩAV = 2
0.04
%
d
Differential Phase at 3.58MHz
RL = 150ΩAV = 2
0.41
°
INPUT CHARACTERISTICS
VOS
Input Referred Offset Voltage
IIN
Input Bias Current (VIN, VINB, VREF)
RIN
Differential Input Resistance
CIN
Differential Input Capacitance
DMIR
Differential Input Range
±2.1
±2.38
CMIR+
Common Mode Positive Input Range at VIN+, VIN-
3.3
3.5
CMIR-
Common Mode Positive Input Range at VIN+, VIN-
VREFIN+
Reference Input Positive Voltage Range
VIN+ = VIN- = 0V
VREFIN-
Reference Input Negative Voltage Range
VIN+ = VIN- = 0V
CMRR
Input Common Mode Rejection Ratio
VIN = ±2.5V
Gain
Gain Accuracy
VIN = 1
FN7311 Rev.12.00
Jul 30, 2020
-14
±7
±25
mV
-6
-3
µA
300
k
1
pF
-4.5
3.3
±2.5
V
V
-4.3
3.7
-3.9
75
95
0.985
1
V
-3.6
dB
1.015
Page 4 of 16
V
EL5172
Electrical Specifications
PARAMETER
VS+ = +5V, VS- = -5V, TA = +25°C, VIN = 0V, RL = 500, RF = 0, RG = OPEN, CL = 2.7pF, Unless Otherwise
Specified. (Continued)
DESCRIPTION
CONDITIONS
MIN
TYP
3.3
3.63
MAX
UNIT
OUTPUT CHARACTERISTICS
Positive Output Voltage Swing
RL = 500Ω to GND
Negative Output Voltage Swing
RL = 500Ω to GND
IOUT(Max)
Maximum Output Current
RL = 10Ω
ROUT
Output Impedance
VOUT
-3.87
±60
V
-3.5
V
±95
mA
100
m
SUPPLY
VSUPPLY
Supply Operating Range
IS (on)
Power Supply Current - Enabled
IS (off)+
Positive Power Supply Current - Disabled
IS (off)-
Negative Power Supply Current - Disabled
PSRR
Power Supply Rejection Ratio
VS+ to VS-
4.75
11
V
5.6
7
mA
80
100
µA
-150
-120
-90
µA
50
58
dB
4.6
EN pin tied to 4.8V
VS from ±4.5V to ±5.5V
ENABLE
tEN
Enable Time
150
ns
tDS
Disable Time
1.4
µs
VIH
EN Pin Voltage for Power-up
VIL
EN Pin Voltage for Shutdown
IIH-EN
EN Pin Input Current High
At VEN = 5V
IIL-EN
EN Pin Input Current Low
At VEN = 0V
FN7311 Rev.12.00
Jul 30, 2020
VS+ - 1.5
V
VS+ - 0.5
V
40
-10
-3
60
µA
µA
Page 5 of 16
EL5172
Typical Performance Curves
AV = 1, RL = 500, CL = 2.7pF
AV = 1, RL = 100, CL = 2.7pF
4
3
3
2
2
1
1
0
MAGNITUDE (dB)
MAGNITUDE (dB)
4
VS = ±5V
-1
-2
-3
-4
-6
1M
10M
-2
VS = ±5V
-3
-4
VS = ±2.5V
-5
0
-1
VS = ±2.5V
-5
100M
-6
1M
1G
FREQUENCY (Hz)
5
3
4
2
3
MAGNITUDE (dB)
NORMALIZED GAIN (dB)
VS = ±5V, RL = 500, CL = 2.7pF
1
0
AV = 1
-2
AV = 5
AV = 10
-4
AV = 2
VS = ±5V, AV = 1, RL = 500
CL = 56pF
CL = 33pF
2
CL = 15pF
1
0
-1
CL = 10pF
-2
CL = 2.7pF
-3
-4
-5
-6
1M
10M
100M
-5
1M
1G
FIGURE 3. FREQUENCY RESPONSE vs VARIOUS GAIN
VS = ±5V, AV = 1, RL = 500
VS = ±5V, AV = 2, RL = 500, CL = 2.7pF
CL = 56pF
3
CL = 33pF
2
1
CL = 15pF
0
CL = 10pF
-2
CL = 2.7pF
-3
-4
NORMALIZED GAIN (dB)
3
2
1
RF = 1k
0
RF = 500
-1
-2
RF = 200
-3
-4
-5
10M
100M
FREQUENCY (Hz)
FIGURE 5. FREQUENCY RESPONSE vs CL
FN7311 Rev.12.00
Jul 30, 2020
1G
4
4
-5
1M
100M
FIGURE 4. FREQUENCY RESPONSE vs CL
5
-1
10M
FREQUENCY (Hz)
FREQUENCY (Hz)
MAGNITUDE (dB)
1G
FIGURE 2. FREQUENCY RESPONSE vs SUPPLY VOLTAGE
4
-3
100M
FREQUENCY (Hz)
FIGURE 1. FREQUENCY RESPONSE vs SUPPLY VOLTAGE
-1
10M
1G
-6
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 6. FREQUENCY RESPONSE FOR VARIOUS RF
Page 6 of 16
EL5172
Typical Performance Curves
270
50
225
2
40
180
1
30
135
20
90
10
45
0
0
0
GAIN (dB)
60
VS = ±5V
-1
-2
VS = ±2.5V
PHASE (°)
AV = 1, RL = 500, CL = 2.7pF
3
4
NORMINALIZED GAIN (dB)
(Continued)
-10
-45
-4
-20
-90
-5
-30
-135
-6
1M
-40
10k
-3
10M
100M
1G
1M
100k
10M
100M
-180
500M
FREQUENCY (Hz)
FREQUENCY (Hz)
FIGURE 7. FREQUENCY RESPONSE FOR VREF
FIGURE 8. OPEN LOOP GAIN
100
0
-10
10
-30
PSRR (dB)
IMPEDANCE ()
-20
1
-40
PSRR+
-50
-60
-70
PSRR-
-80
0.1
10k
-90
100k
1M
10M
100M
1k
100k
10k
FREQUENCY (Hz)
1M
10M
100M
FREQUENCY (Hz)
FIGURE 9. OUTPUT IMPEDANCE vs FREQUENCY
FIGURE 10. PSRR vs FREQUENCY
100
1k
VOLTAGE NOISE (nV/Hz)
CURRENT NOISE (pA/Hz)
90
80
CMRR (dB)
70
60
50
40
30
20
100
EN
10
IN
10
0
100k
1M
10M
100M
FREQUENCY (Hz)
FIGURE 11. CMRR vs FREQUENCY
FN7311 Rev.12.00
Jul 30, 2020
1G
1
10
100
1k
10k
100k
1M
10M
FREQUENCY (Hz)
FIGURE 12. VOLTAGE AND CURRENT NOISE vs FREQUENCY
Page 7 of 16
EL5172
Typical Performance Curves
(Continued)
-45
VS = ±5V, RL = 500, f = 5MHz
DISTORTION (dB)
-50
-55
HD
-60
-65
H
AV
D2 (
2 (A V
= 2)
HD3 (A V = 2)
= 1)
-70
-75
HD3 (AV = 1)
-80
-85
1
2
3
4
5
7
6
VOP-P (V)
FIGURE 13. HARMONIC DISTORTION vs OUTPUT VOLTAGE
-50
V =2
)
-55
DISTORTION (dB)
-40
HD
3 (A
HD2 (A
V = 2)
-60
-65
HD2 (AV = 1)
-70
-75
-80
200
300
HD2
400
500
600
700
800
(A V =
2)
HD3 (A V
-60
HD2 (A V
-70
= 2)
= 1)
HD3 (AV = 1)
-80
-90
HD3 (AV = 1)
-85
-80
100
VS = ±5V, RL = 500, VOP-P = 1V FOR AV = 1,
VOP-P = 2V for AV = 2
-50
DISTORTION (dB)
-45
VS = ±5V, f = 5MHz, VOP-P = 1V @AV = 1,
VOP-P = 2V @AV = 2
900 1000
-100
RLOAD ()
0
5
10
15
20
25
30
35
40
FREQUENCY (MHz)
FIGURE 14. HARMONIC DISTORTION vs LOAD RESISTANCE
FIGURE 15. HARMONIC DISTORTION vs FREQUENCY
50mV/DIV
0.5V/DIV
10ns/DIV
FIGURE 16. SMALL SIGNAL TRANSIENT RESPONSE
FN7311 Rev.12.00
Jul 30, 2020
10ns/DIV
FIGURE 17. LARGE SIGNAL TRANSIENT RESPONSE
Page 8 of 16
EL5172
Typical Performance Curves
(Continued)
M = 400ns, CH1 = 200mV/DIV, CH2 = 5V/DIV
M = 100ns, CH1 = 200mV/DIV, CH2 = 5V/DIV
CH1
CH1
CH2
CH2
400ns/DIV
100ns/DIV
FIGURE 18. ENABLED RESPONSE
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
1.4
1.0
POWER DISSIPATION (W)
POWER DISSIPATION (W)
1.2
FIGURE 19. DISABLED RESPONSE
0.8
625mW
0.6
SOIC8
JA = +160°C/W
0.4 486mW
MSOP8
JA = +206°C/W
0.2
0
0
25
50
75 85 100
125
1.2
1.0
909mW
0.8
870mW
SOIC8
JA = +110°C/W
0.6
MSOP8/10
JA = +115°C/W
0.4
0.2
0
150
JEDEC JESD51-7 HIGH EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
0
25
AMBIENT TEMPERATURE (°C)
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 20. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
FIGURE 21. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
Simplified Schematic
VS+
I1
VIN+
Q1
I2
RD1
VINQ2
I3
FBP
Q3
I4
RD2
FBN
Q4
R3
R4
Q8
Q7
VB1
Q9
x1
VOUT
Q6
25
VB2
CC
R1
R2
VS-
FN7311 Rev.12.00
Jul 30, 2020
Page 9 of 16
EL5172
Description of Operation and Application
Information
Product Description
The EL5172 is a low-power, wideband, differential to
single-ended amplifier. The EL5172 is internally
compensated for closed loop gain of +1 or greater.
Connected in gain of 1 and driving a 500Ω load, the EL5172
has a -3dB bandwidth of 250MHz. Driving a 150Ω load at
gain of 2, the bandwidth is about 50MHz. The bandwidth at
the REF input is about 450MHz. The EL5172 is available
with a power-down feature to reduce the power while the
amplifier is disabled.
Input, Output and Supply Voltage Range
The EL5172 is designed to operate with a single supply
voltage of 5V to 10V or split supplies with its total voltage
from 5V to 10V. The amplifier has an input common mode
voltage range from -4.3V to 3.3V for ±5V supply. The
differential mode input range (DMIR) between the two inputs
is about from -2.3V to +2.3V. The input voltage range at the
REF pin is from -3.6V to 3.3V. If the input common mode or
differential mode signal is outside the above-specified
ranges, it will cause the output signal to be distorted.
The output of the EL5172 can swing from -3.8V to 3.6V at
500Ω load at ±5V supply. As the load resistance becomes
lower, the output swing is reduced respectively.
Overall Gain Settings
The gain setting for the EL5172 is similar to the conventional
operational amplifier. The output voltage is equal to the
difference of the inputs plus VREF and then times the gain,
as expressed in Equation 1.
RF
V O = V IN + – V IN - + V REF 1 + --------
R
G
(EQ. 1)
EN
VIN+
VIN-
+
VREF
FB
G/B
VO
+
-
The bandwidth of the EL5172 depends on the load and the
feedback network. RF and RG appear in parallel with the
load for gains other than +1. As this combination gets
smaller, the bandwidth falls off. Consequently, RF also has a
minimum value that should not be exceeded for optimum
bandwidth performance. For a gain of +1, RF = 0 is optimum.
For the gains other than +1, optimum response is obtained
with RF between 500Ω to 1kΩ. For AV = 2 and RF = RG =
1kΩ, the BW is about 80MHz and the frequency response is
very flat.
The EL5172 has a gain bandwidth product of 100MHz. For
gains 5, its bandwidth can be predicted using Equation 2:
(EQ. 2)
Gain BW = 100MHz
Driving Capacitive Loads and Cables
The EL5172 can drive 56pF capacitance in parallel with
500Ω load to ground with 4dB of peaking at a gain of +1. If
less peaking is desired in applications, a small series resistor
(usually between 5Ω to 50Ω) can be placed in series with
each output to eliminate most peaking. However, this will
reduce the gain slightly. If the gain setting is greater than 1,
the gain resistor RG can then be chosen to make-up for any
gain loss which may be created by the additional series
resistor at the output.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier's output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help
to reduce peaking.
Disable/Power-Down
RF
RG
FIGURE 22.
Choice of Feedback Resistor and Gain Bandwidth
Product
For applications that require a gain of +1, no feedback
resistor is required; just short the OUT pin to the FB pin. For
gains greater than +1, the feedback resistor forms a pole
with the parasitic capacitance at the inverting input. As this
FN7311 Rev.12.00
Jul 30, 2020
pole becomes smaller, the amplifier's phase margin is
reduced. This causes ringing in the time domain and
peaking in the frequency domain. Therefore, RF has some
maximum value that should not be exceeded for optimum
performance. If a large value of RF must be used, a small
capacitor in the few Pico farad range in parallel with RF can
help to reduce the ringing and peaking at the expense of
reducing the bandwidth.
The EL5172 can be disabled and its outputs placed in a high
impedance state. The turn-off time is about 1.4µs and the
turn-on time is about 150ns. When disabled, the amplifier's
supply current is reduced to 80µA for IS+ and 120µA for IStypically, thereby effectively eliminating the power
consumption. The amplifier's power-down can be controlled
by standard CMOS signal levels at the ENABLE pin. The
applied logic signal is relative to VS+ pin. Letting the EN pin
float or applying a signal that is less than 1.5V below VS+
enables the amplifier. The amplifier will be disabled when the
signal at EN pin is above VS+ - 0.5V. If a TTL signal controls
Page 10 of 16
EL5172
the enabled/disabled function, Figure 23 could be used to
convert the TTL signal to CMOS signal.
5V
Where:
• VS = Total supply voltage
• ISMAX = Maximum quiescent supply current
10k
1k
• VOUT = Maximum output voltage of the application
EN
• RLOAD = Load resistance
CMOS/TTL
• ILOAD = Load current
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOAD to avoid the device
overheat.
FIGURE 23.
Output Drive Capability
The EL5172 has internal short-circuit protection. Its typical
short-circuit current is ±95mA. If the output is shorted
indefinitely, the power dissipation could easily increase such
that the part will be destroyed. Maximum reliability is
maintained if the output current never exceeds ±60mA. This
limit is set by the design of the internal metal
interconnections.
Power Dissipation
With the high output drive capability of the EL5172, it is
possible to exceed the +135°C absolute maximum junction
temperature under certain load current conditions.
Therefore, it is important to calculate the maximum junction
temperature for the application to determine if the load
conditions or package types need to be modified for the
amplifier to remain in the safe operating area.
The maximum power dissipation allowed in a package is
determined according to Equation 3:
T JMAX – T AMAX
PD MAX = -------------------------------------------- JA
(EQ. 3)
• TJMAX = Maximum junction temperature
• TAMAX = Maximum ambient temperature
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, a good printed circuit
board layout is necessary for optimum performance. Lead
lengths should be as short as possible. The power supply
pin must be well bypassed to reduce the risk of oscillation.
For normal single supply operation, where the VS- pin is
connected to the ground plane, a single 4.7µF tantalum
capacitor in parallel with a 0.1µF ceramic capacitor from VS+
to GND will suffice. This same capacitor combination should
be placed at each supply pin to ground if split supplies are to
be used. In this case, the VS- pin becomes the negative
supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire wound resistors should be
avoided because of their additional series inductance. Use
of sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier's inverting input pin is very important. The
feedback resistor should be placed very close to the
inverting input pin. Strip line design techniques are
recommended for the signal traces.
• JA = Thermal resistance of the package
Assuming the REF pin is tied to GND for VS = ±5V
application, the maximum power dissipation actually
produced by an IC is the total quiescent supply current times
the total power supply voltage, plus the power in the IC due
to the load, or:
For sourcing, use Equation 4:
V OUT
PD MAX = V S I SMAX + V S + – V OUT -------------------R
(EQ. 4)
LOAD
For sinking, use Equation 5:
PD MAX = V S I SMAX + V OUT – V S - I LOAD
FN7311 Rev.12.00
Jul 30, 2020
(EQ. 5)
Page 11 of 16
EL5172
Typical Applications
0
50
VFB
50
EL5173,
EL5373
VIN
50
50
ZO = 100
EL5172
VOUT
VINB
VREF
FIGURE 24. TWISTED PAIR CABLE RECEIVER
R3
R1
R2
GAIN
(dB)
C1
1 + R2/R1
VFB
50
ZO = 100
VIN
EL5172
VOUT
VINB
50
1 + R2/(R1 + R3)
VREF
fA
fC
f
FIGURE 25. COMPENSATED LINE RECEIVER
5V
CB
0.1µ
CG
100 n
CS
4.7µ
RG
RF
1
VID
RT
100 Ω
C IN
100 n
2
3
C IN
100 n
4
RIN
10k
6
FBP
IN+
8
OUT
INREF
EL5172
5
7
RIN
10k
5V
ISL21090-25
6
2.5V
CB
0.1µ
VO
EN
5
VOUT
TRIM
VIN
COMP
GND
2
3
CB
0.1µ
CS
4.7µ
4
FIGURE 26. Single Supply Operation
FN7311 Rev.12.00
Jul 30, 2020
Page 12 of 16
EL5172
As the signal is transmitted through a cable, the high frequency
signal will be attenuated. One way to compensate for this loss
is to boost the high frequency gain at the receiver side.
Level Shifter and Signal Summer
The EL5172 contains two pairs of differential pair input stages,
which make sure that the inputs are all high impedance inputs.
To take advantage of the two high impedance inputs, the
EL5172 can be used as a signal summer to add two signals
together. One signal can be applied to VIN+, the second signal
can be applied to REF and VIN- is ground. The output is equal
to Equation 6:
V O = V IN + + V REF Gain
(EQ. 6)
Also, the EL5172 can be used as a level shifter by applying a
level control signal to the REF input.
FN7311 Rev.12.00
Jul 30, 2020
Page 13 of 16
EL5172
Revision History
The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make
sure that you have the latest revision.
DATE
REVISION
Jul 30, 2020
12.00
Added Related Literature section.
Removed EL5372 information from datasheet.
Updated Ordering Information table by adding tape and reel information and updating notes.
Added Figure 27.
Removed About Intersil section.
Aug 11, 2015
11.00
Updated Ordering Information table on page 2.
FN7311 Rev.12.00
Jul 30, 2020
CHANGE
Page 14 of 16
EL5172
Package Outline Drawings
For the most recent package outline drawing, see M8.15E.
M8.15E
8 Lead Narrow Body Small Outline Plastic Package
Rev 0, 08/09
4
4.90 ± 0.10
A
DETAIL "A"
0.22 ± 0.03
B
6.0 ± 0.20
3.90 ± 0.10
4
PIN NO.1
ID MARK
5
(0.35) x 45°
4° ± 4°
0.43 ± 0.076
1.27
0.25 M C A B
SIDE VIEW “B”
TOP VIEW
1.75 MAX
1.45 ± 0.1
0.25
GAUGE PLANE
C
SEATING PLANE
0.10 C
0.175 ± 0.075
SIDE VIEW “A
0.63 ±0.23
DETAIL "A"
(1.27)
(0.60)
NOTES:
(1.50)
(5.40)
1.
Dimensions are in millimeters.
Dimensions in ( ) for Reference Only.
2.
Dimensioning and tolerancing conform to AMSE Y14.5m-1994.
3.
Unless otherwise specified, tolerance : Decimal ± 0.05
4.
Dimension does not include interlead flash or protrusions.
Interlead flash or protrusions shall not exceed 0.25mm per side.
5.
The pin #1 identifier may be either a mold or mark feature.
6.
Reference to JEDEC MS-012.
TYPICAL RECOMMENDED LAND PATTERN
FN7311 Rev.12.00
Jul 30, 2020
Page 15 of 16
EL5172
M8.118A
8 Lead Mini Small Outline Plastic Package (MSOP)
Rev 0, 9/09
3.0±0.1
8
For the most recent package outline drawing, see M8.118A.
A
0.25
CAB
3.0±0.1
4.9±0.15
DETAIL "X"
1.10 Max
PIN# 1 ID
B
SIDE VIEW 2
1
0.18 ± 0.05
2
0.65 BSC
TOP VIEW
0.95 BSC
0.86±0.09
H
GAUGE
PLANE
C
0.25
SEATING PLANE
0.33 +0.07/ -0.08
0.08 C A B
0.10 ± 0.05
3°±3°
0.10 C
0.55 ± 0.15
DETAIL "X"
SIDE VIEW 1
5.80
NOTES:
4.40
3.00
1.
Dimensions are in millimeters.
2.
Dimensioning and tolerancing conform to JEDEC MO-187-AA
and AMSE Y14.5m-1994.
3.
Plastic or metal protrusions of 0.15mm max per side are not
included.
4.
Plastic interlead protrusions of 0.25mm max per side are not
included.
5.
Dimensions “D” and “E1” are measured at Datum Plane “H”.
6.
This replaces existing drawing # MDP0043 MSOP 8L.
0.65
0.40
1.40
TYPICAL RECOMMENDED LAND PATTERN
FN7311 Rev.12.00
Jul 30, 2020
Page 16 of 16
IMPORTANT NOTICE AND DISCLAIMER
RENESAS ELECTRONICS CORPORATION AND ITS SUBSIDIARIES (“RENESAS”) PROVIDES TECHNICAL
SPECIFICATIONS AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING
REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND
OTHER RESOURCES “AS IS” AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for developers skilled in the art designing with Renesas products. You are solely responsible
for (1) selecting the appropriate products for your application, (2) designing, validating, and testing your application, and (3)
ensuring your application meets applicable standards, and any other safety, security, or other requirements. These
resources are subject to change without notice. Renesas grants you permission to use these resources only for
development of an application that uses Renesas products. Other reproduction or use of these resources is strictly
prohibited. No license is granted to any other Renesas intellectual property or to any third party intellectual property.
Renesas disclaims responsibility for, and you will fully indemnify Renesas and its representatives against, any claims,
damages, costs, losses, or liabilities arising out of your use of these resources. Renesas' products are provided only subject
to Renesas' Terms and Conditions of Sale or other applicable terms agreed to in writing. No use of any Renesas resources
expands or otherwise alters any applicable warranties or warranty disclaimers for these products.
(Rev.1.0 Mar 2020)
Corporate Headquarters
Contact Information
TOYOSU FORESIA, 3-2-24 Toyosu,
Koto-ku, Tokyo 135-0061, Japan
www.renesas.com
For further information on a product, technology, the most
up-to-date version of a document, or your nearest sales
office, please visit:
www.renesas.com/contact/
Trademarks
Renesas and the Renesas logo are trademarks of Renesas
Electronics Corporation. All trademarks and registered
trademarks are the property of their respective owners.
© 2020 Renesas Electronics Corporation. All rights reserved.