DATASHEET
SIGNS
NE W D E
R
O
F
D
T
ND E
ACEMEN
COMME
EL8202, EL8203, EL8403
ED REPL Center at
N OT R E
D
N
E
M
OM
upport
NO REC
chnical S .intersil.com/tsc
e
500MHz Rail-to-Rail Amplifiers
T
r
u
o
t
contac ERSIL or www
T
1-888-IN
FN7106
Rev 2.00
April 26, 2006
The EL8202, EL8203, and EL8403 represent rail-to-rail
amplifiers with a -3dB bandwidth of 500MHz and slew rate of
600V/µs. Running off a very low supply current of 5.6mA per
channel, the EL8202, EL8203, and EL8403 also feature
inputs that go to 0.15V below the VS- rail. The EL8202 and
EL8203 are dual channel amplifiers. The EL8403 is a quad
channel amplifier.
Features
The EL8202 includes a fast-acting disable/power-down
circuit. With a 25ns disable and a 200ns enable, the EL8202
is ideal for multiplexing applications.
• Rail-to-rail output
The EL8202, EL8203, and EL8403 are designed for a
number of general purpose video, communication,
instrumentation, and industrial applications. The EL8202 is
available in a 10 Ld MSOP package, the EL8203 in 8 Ld SO
and 8 Ld MSOP packages, and the EL8403 in 14 Ld SO and
16 Ld QSOP packages. All are specified for operation over
the -40°C to +85°C temperature range.
• 500MHz -3dB bandwidth
• 600V/µs slew rate
• Low supply current = 5.6mA per channel
• Supplies from 3V to 5.5V
• Input to 0.15V below VS• Fast 25ns disable (EL8202 only)
• Low cost
• Pb-free plus anneal available (RoHS compliant)
Applications
• Video amplifiers
• Portable/hand-held products
• Communications devices
Ordering Information (Continued)
Ordering Information
PART
NUMBER
PART
TAPE &
MARKING REEL
PACKAGE
PKG.
DWG. #
PART
NUMBER
PART
TAPE &
MARKING REEL
PACKAGE
PKG.
DWG. #
EL8202IY
m
-
10 Ld MSOP MDP0043
EL8403IS
8403IS
-
14 Ld SO
MDP0027
EL8202IY-T7
m
7”
10 Ld MSOP MDP0043
EL8403IS-T7
8403IS
7”
14 Ld SO
MDP0027
EL8202IY-T13
m
13”
10 Ld MSOP MDP0043
EL8403IS-T13
8403IS
13”
14 Ld SO
MDP0027
EL8202IYZ
(See Note)
BAPAA
-
10 Ld MSOP MDP0043
(Pb-free)
EL8403ISZ
(See Note)
8403ISZ
-
14 Ld SO
(Pb-free)
MDP0027
EL8202IYZ-T7
(See Note)
BAPAA
7”
10 Ld MSOP MDP0043
(Pb-free)
EL8403ISZ-T7
(See Note)
8403ISZ
7”
14 Ld SO
(Pb-free)
MDP0027
EL8202IYZ-T13 BAPAA
(See Note)
13”
10 Ld MSOP MDP0043
(Pb-free)
EL8403ISZ-T13 8403ISZ
(See Note)
13”
14 Ld SO
(Pb-free)
MDP0027
EL8203IS
8203IS
-
8 Ld SO
MDP0027
EL8403IU
8403IU
-
16 Ld QSOP MDP0040
EL8203IS-T7
8203IS
7”
8 Ld SO
MDP0027
EL8403IU-T7
8403IU
7”
16 Ld QSOP MDP0040
EL8203IS-T13
8203IS
13”
8 Ld SO
MDP0027
EL8403IU-T13
8403IU
13”
16 Ld QSOP MDP0040
8403IUZ
-
16 Ld QSOP MDP0040
(Pb-free)
EL8203ISZ
(See Note)
8203ISZ
-
8 Ld SO
(Pb-free)
MDP0027
EL8403IUZ
(See Note)
EL8203ISZ-T7
(See Note)
8203ISZ
7”
8 Ld SO
(Pb-free)
MDP0027
EL8403IUZ-T7
(See Note)
8403IUZ
7”
16 Ld QSOP MDP0040
(Pb-free)
EL8203ISZ-T13 8203ISZ
(See Note)
13”
8 Ld SO
(Pb-free)
MDP0027
EL8403IUZ-T13 8403IUZ
(See Note)
13”
16 Ld QSOP MDP0040
(Pb-free)
NOTE: Intersil Pb-free plus anneal products employ special Pb-free
material sets; molding compounds/die attach materials and 100% matte
tin plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
EL8203IY
BJAAA
-
8 Ld MSOP
MDP0043
EL8203IY-T7
BJAAA
7”
8 Ld MSOP
MDP0043
EL8203IY-T13
BJAAA
13”
8 Ld MSOP
MDP0043
FN7106 Rev 2.00
April 26, 2006
Page 1 of 16
EL8202, EL8203, EL8403
Pinouts
EL8203
(8 LD SO, MSOP)
TOP VIEW
EL8202
(10 LD MSOP)
TOP VIEW
10 INA-
INA+ 1
+
CEA 2
VS- 3
+
-
CEB 4
9 OUTA
INA- 2
8 VS+
INA+ 3
7 OUTB
OUTA 1
A
- +
D
+ -
VS+ 4
- +
B
+ C
OUTA 1
13 IND-
INA- 2
12 IND+
INA+ 3
11 VS-
INB+ 5
10 INC+
INB+ 5
9 INC-
INB- 6
8 OUTC
16 OUTD
- +
+ -
OUTB 7
15 IND14 IND+
VS+ 4
NC 8
FN7106 Rev 2.00
April 26, 2006
5 INB+
EL8403
(16 LD QSOP)
TOP VIEW
14 OUTD
INA+ 3
OUTB 7
6 INB+
VS- 4
EL8403
(14 LD SO)
TOP VIEW
INB- 6
7 OUTB
+
6 INB-
INB+ 5
INA- 2
8 VS+
OUTA 1
13 VS12 INC+
- +
+ -
11 INC10 OUTC
9 NC
Page 2 of 16
EL8202, EL8203, EL8403
Absolute Maximum Ratings (TA = 25°C)
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +125°C
Supply Voltage from VS+ to VS- . . . . . . . . . . . . . . . . . . . . . . . . 5.5V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . VS+ +0.3V to VS- -0.3V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 40mA
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
Electrical Specifications
PARAMETER
VS+ = 5V, VS- = GND, TA = 25°C, VCM = 2.5V, RL to 2.5V, AV = 1, Unless Otherwise Specified
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
-8
-0.8
+8
UNIT
INPUT CHARACTERISTICS
VOS
Offset Voltage
TCVOS
Offset Voltage Temperature Coefficient
Measured from TMIN to TMAX
IB
Input Bias Current
VIN = 0V
IOS
Input Offset Current
VIN = 0V
TCIOS
Input Bias Current Temperature
Coefficient
Measured from TMIN to TMAX
CMRR
Common Mode Rejection Ratio
VCM = -0.15V to +3.5V (EL8202,EL8203)
VCM = -0.15V to +3.5V (EL8403)
CMIR
Common Mode Input Range
RIN
Input Resistance
CIN
Input Capacitance
AVOL
Open Loop Gain
-9
mV
3
µV/°C
-6
µA
0.1
0.6
µA
2
nA/°C
70
95
dB
60
85
dB
VS- 0.15
Common Mode
VS+ 1.5
V
3.5
M
0.5
pF
90
dB
VOUT = +1.5V to +3.5V, RL = 150 to GND
80
dB
30
m
VOUT = +1.5V to +3.5V, RL = 1k to GND
75
OUTPUT CHARACTERISTICS
ROUT
Output Resistance
AV = +1
VOP
Positive Output Voltage Swing
RL = 1k
4.85
4.9
V
RL = 150
4.6
4.7
V
VON
Negative Output Voltage Swing
RL = 150
100
150
mV
RL = 1k (EL8202,EL8203)
25
50
mV
RL = 1k (EL8403)
50
100
mV
IOUT
Linear Output Current
65
mA
ISC (source)
Short Circuit Current
RL = 10
60
80
mA
ISC (sink)
Short Circuit Current
RL = 10
120
150
mA
VS+ = 4.5V to 5.5V
70
95
dB
POWER SUPPLY
PSRR
Power Supply Rejection Ratio
IS-ON
Supply Current - Enabled (per amplifier)
5.6
6.2
mA
IS-OFF
Supply Current - Disabled (per amplifier) EL8202 only
40
90
µA
ENABLE (EL8202 ONLY)
tEN
Enable Time
200
ns
tDS
Disable Time
25
ns
VIH-ENB
ENABLE Pin Voltage for Power-up
0.8
V
VIL-ENB
ENABLE Pin Voltage for Shut-down
2
V
FN7106 Rev 2.00
April 26, 2006
Page 3 of 16
EL8202, EL8203, EL8403
Electrical Specifications
PARAMETER
VS+ = 5V, VS- = GND, TA = 25°C, VCM = 2.5V, RL to 2.5V, AV = 1, Unless Otherwise Specified (Continued)
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
IIH-ENB
ENABLE Pin Input Current High
8.6
µA
IIL-ENB
ENABLE Pin Input for Current Low
0.01
µA
AC PERFORMANCE
BW
-3dB Bandwidth
AV = +1, RF = 0, CL = 2.5pF
500
MHz
AV = -1, RF = 1k, CL = 2.5pF
140
MHz
AV = +2, RF = 1k, CL = 2.5pF
165
MHz
AV = +10, RF = 1k, CL = 2.5pF
18
MHz
BW
±0.1dB Bandwidth
AV = +1, RF = 0, CL = 2.5pF
35
MHz
Peak
Peaking
AV = +1, RL = 1k, CL = 2.5pF
2
dB
GBWP
Gain Bandwidth Product
200
MHz
PM
Phase Margin
RL = 1k, CL = 2.5pF
55
°
SR
Slew Rate
AV = 2, RL = 100, VOUT = 0.5V to 4.5V
600
V/µs
tR
Rise Time
2.5VSTEP, 20% - 80%
500
4
ns
tF
Fall Time
2.5VSTEP, 20% - 80%
2
ns
OS
Overshoot
200mV step
10
%
tPD
Propagation Delay
200mV step
1
ns
tS
0.1% Settling Time
200mV step
15
ns
dG
Differential Gain
AV = +2, RF = 1k, RL = 150
0.01
%
dP
Differential Phase
AV = +2, RF = 1k, RL = 150
0.01
°
eN
Input Noise Voltage
f = 10kHz
12
nV/Hz
iN+
Positive Input Noise Current
f = 10kHz
1.7
pA/Hz
iN-
Negative Input Noise Current
f = 10kHz
1.3
pA/Hz
eS
Channel Separation
f = 100kHz
95
dB
Pin Descriptions
EL8202
(MSOP-10)
EL8203
(SO-8,
MSOP-8)
EL8403
(SO-14)
EL8403
(QSOP-16)
NAME
1, 5
3, 5
3, 5, 10, 12
3,5,12,14
IN+
Non-inverting input for each channel
CE
Enable and disable input for each channel
2, 4
FUNCTION
3
4
11
13
VS-
Negative power supply
6, 10
2, 6
2, 6, 9, 13
2,6,11,15
IN-
Inverting input for each channel
7, 9
1, 7
1, 7, 8, 14
1,7,10,16
OUT
Amplifier output for each channel
8
8
4
4
VS+
Positive power supply
FN7106 Rev 2.00
April 26, 2006
Page 4 of 16
EL8202, EL8203, EL8403
Typical Performance Curves
3
2
GAIN (dB)
5
VS=5V
AV=1
RL=1k
CL=2.5pF
NORMALIZED GAIN (dB)
5
4
VOP-P=200mV
1
0
-1
VOP-P=1V
-2
-3
VOP-P=2V
-4
-5
1M
10M
100M
3
RF=RG=1k
1
-1
-3
RF=RG=500
VS=5V
AV=2
RL=1k
CL=2.5pF
-5
100K
1G
1M
FREQUENCY (Hz)
4
NORMALIZED GAIN (dB)
NORMALIZED GAIN (dB)
3
AV=1
2
AV=2
1
0
-1
-2
-3
-4
AV=5
AV=10
-5
1M
10M
100M
2
VS=5V
CL=2.5pF
RL=1k
RF=1k
AV=-1
AV=-5
-2
-4
AV=-10
-6
100K
1G
1M
11
9
RL=1k
GAIN (dB)
GAIN (dB)
1
0
-1
RL=500
7
5
RL=1k,
150
-5
1M
3
RL=500
-4
10M
100M
1G
FREQUENCY (Hz)
FIGURE 5. SMALL SIGNAL FREQUENCY RESPONSE FOR
VARIOUS NON-INVERTING GAINS
FN7106 Rev 2.00
April 26, 2006
1G
VS=5V
AV=2
CL=2.5pF
RF=RG=1k
-2
-3
100M
FIGURE 4. SMALL SIGNAL FREQUENCY RESPONSE FOR
VARIOUS INVERTING GAINS
5
2
10M
FREQUENCY (Hz)
FIGURE 3. SMALL SIGNAL FREQUENCY RESPONSE FOR
VARIOUS NON-INVERTING GAINS
RL=100
1G
0
FREQUENCY (Hz)
V =5V
4 AS=1
V
3 CL=2.5pF
100M
FIGURE 2. SMALL SIGNAL FREQUENCY RESPONSE
vs RF AND RG
5
VS=5V
CL=2.5pF
RL=1k
10M
FREQUENCY (Hz)
FIGURE 1. FREQUENCY RESPONSE FOR VARIOUS OUTPUT
VOLTAGE LEVELS
4
RF=RG=2k
1
100K
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 6. SMALL SIGNAL FREQUENCY RESPONSE vs
VARIOUS RLOAD
Page 5 of 16
EL8202, EL8203, EL8403
Typical Performance Curves (Continued)
5
16
VS=5V
AV=1
RL=1k
4
3
CL=5.4pF
12
CL=2.5pF
3
1
0
CL=1.5pF
-1
6
2
0
-4
-2
100M
CL=10pF
4
-3
10M
CL=20pF
8
-2
-5
1M
CL=2.5pF
-4
100K
1G
1M
FREQUENCY (Hz)
RL=150
30
405
-10
315
-30
225
RL=150
-10
-50
135
RL=1k
-90
1K
100K
1M
10M
100M
VS=5V
AV=1
RL=1k
-50
-70
-110
1K
-45
1G
10K
FIGURE 9. OPEN LOOP GAIN AND PHASE vs FREQUENCY
600
100M
1G
RL=1k
CL=2.5pF
550
500
BANDWIDTH (MHz)
-30
PSRR (dB)
10M
FIGURE 10. DISABLED OUTPUT ISOLATION FREQUENCY
RESPONSE
-10
PSRR-
-70
1M
100K
FREQUENCY (Hz)
FREQUENCY (Hz)
-50
1G
-90
45
10K
100M
FIGURE 8. SMALL SIGNAL FREQUENCY RESPONSE FOR
VARIOUS CL
GAIN (dB)
GAIN (dB)
RL=1k
PHASE (°)
110
10M
FREQUENCY (Hz)
FIGURE 7. SMALL SIGNAL FREQUENCY RESPONSE VS CL
70
CL=28.5pF
10
GAIN (dB)
GAIN (dB)
VS=5V
AV=2
RF=RG=1k
14
PSRR+
-90
AV=1
450
400
350
300
250
AV=2
200
150
-110
1K
100
10K
100K
1M
10M
100M
FREQUENCY (Hz)
FIGURE 11. POWER SUPPLY REJECTION RATIO vs
FREQUENCY
FN7106 Rev 2.00
April 26, 2006
3
3.5
4.5
4
5
5.5
VS (V)
FIGURE 12. SMALL SIGNAL BANDWIDTH vs SUPPLY
VOLTAGE
Page 6 of 16
EL8202, EL8203, EL8403
Typical Performance Curves (Continued)
100
3.5
RL=1k
CL=1.5pF
10
PEAKING (dB)
IMPEDANCE ()
3
1
0.1
AV=1
2.5
2
1.5
1
AV=2
0.5
0
0.01
10K
100K
1M
10M
3
100M
3.5
4.5
4
FREQUENCY (Hz)
-15
10
-35
8
-55
6
-75
4
2
-95
0
-115
100K
1M
10M
100M
0
0.5
1
1.5
2
2.5
HD2
-90
HD2@5MHz
Hz
@ 1M
MHz
HD3@ 5
1
-75
HD2@10MHz
DISTORTION (dBc)
-80
2
H
HD3@10M
z
4.5
HD3@1MHz
3
4
5
FIGURE 17. HARMONIC DISTORTION vs OUTPUT VOLTAGE
HD2@
-80
5
5.5
H D 2@
AV =2
AV =1
-85
VS=5V
f=5MHz
-90
-95
VOP-P (V)
FN7106 Rev 2.00
April 26, 2006
4
-70
VS=5V
RL=1k
CL=2.5pF
AV=2
-70
3.5
FIGURE 16. SUPPLY CURRENT vs SUPPLY VOLTAGE
(PER CHANNEL)
FIGURE 15. COMMON-MODE REJECTION RATIO vs
FREQUENCY
-60
3
VS (V)
FREQUENCY (Hz)
DISTORTION (dBc)
5.5
FIGURE 14. SMALL SIGNAL PEAKING vs SUPPLY VOLTAGE
IS (mA)
CMRR (dB)
FIGURE 13. OUPUT IMPEDANCE vs FREQUENCY
-100
5
VS (V)
H D 3@
VO=1VP-P for AV=1
VO=2VP-P for AV=2
-100
100
H D 3@
AV =2
AV =1
1K
2K
RLOAD ()
FIGURE 18. HARMONIC DISTORTION vs LOAD RESISTANCE
Page 7 of 16
EL8202, EL8203, EL8403
Typical Performance Curves (Continued)
-50
1K
DISTORTION (dBc)
-60
-70
AV=
HD2@
-80
-90
-100
VOLTAGE NOISE (nV/Hz)
CURRENT NOISE (pA/Hz),
VS=5V
RL=1k
CL=2.5pF
VO=1VP-P for AV=1
VO=2VP-P for AV=2
2
HD2@AV=1
HD3@AV=2
@
HD 3
AV=1
10
1
100
eN
10
IN+
1
10
40
100
FREQUENCY (MHz)
10K
100K
1M
10M
FIGURE 20. VOLTAGE AND CURRENT NOISE vs FREQUENCY
0
CHANNEL SEPARATION (dB)
0
CHANNEL SEPARATION (dB)
1K
FREQUENCY (Hz)
FIGURE 19. HARMONIC DISTORTION vs FREQUENCY
-10
-20
-30
-40
CH1CH2
-50
-60
-70
-80
-90
-100
100K
1M
10M
100M
1G
-10
-20
-30
-40
-50
FIGURE 21. CHANNEL SEPARATION vs FREQUENCY
(EL8202 AND EL8203)
VS=5V
AV=1
RL=1k to 2.5V
CL=5pF
-70
CH1CH4
CH2CH3
-80
CH1CH3
CH2CH4
-90
-100
100K
1M
10M
100M
1G
FREQUENCY (Hz)
FIGURE 22. CHANNEL SEPARATION vs FREQUENCY
(EL8403)
VS=5V
AV=1
RL=1k to 2.5V
CL=5pF
3.5
2.5
2.5
1.5
1.5
2ns/DIV
FIGURE 23. LARGE SIGNAL TRANSIENT
RESPONSE - RISING
FN7106 Rev 2.00
April 26, 2006
CH1CH2
-60
FREQUENCY (Hz)
3.5
IN-
2ns/DIV
FIGURE 24. LARGE SIGNAL TRANSIENT
RESPONSE - FALLING
Page 8 of 16
EL8202, EL8203, EL8403
Typical Performance Curves (Continued)
2.6
2.5
VS=5V, AV=1, RL=1k TO 2.5V, CL= 2.5pF
VS=5V, AV=5, RL=1k to 2.5V
VIN
5
2.4
2.5
2.6
VOUT
2.5
0
2.4
2µs/DIV
10ns/DIV
FIGURE 25. SMALL SIGNAL TRANSIENT REPONSE
VS=5V, AV=5, RL=1k TO 2.5V
FIGURE 26. OUTPUT SWING
CH1
ENABLE
INPUT
5
2.5
CH2
VOUT
0
CH1, CH2, 1V/DIV, M=100ns
2µs/DIV
FIGURE 27. OUTPUT SWING
FIGURE 28. ENABLED RESPONSES (EL8202)
CH1
CH2
POWER DISSIPATION (W)
JEDEC JESD51-3 LOW EFFECTIVE THERMAL
CONDUCTIVITY TEST BOARD
ENABLE
INPUT
VOUT
1
0.9 833mW
0.8
0.3
FIGURE 29. DISABLED RESPONSE (EL8202)
FN7106 Rev 2.00
April 26, 2006
JA
=
MSOP8/10
JA=206°C/W
0.2
SO
12
0
14
°C
/W
SO8
JA=160°C/W
QSOP16
JA=158°C/W
0.1
0
CH1, CH2, 0.5V/DIV, M=20ns
0.7 625mW
0.6
633mW
0.5
0.4 486mW
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 30. PACKAGE POWER DISSIPATION vs AMBIENT
TEMPERATURE
Page 9 of 16
EL8202, EL8203, EL8403
Typical Performance Curves (Continued)
POWER DISSIPATION (W)
1.4
JEDEC JESD51-7 HIGH EFFECTIVE
THERMAL CONDUCTIVITY TEST BOARD
1.2 1.136W
1 909mW
0.8
JA
893mW
870mW
MSOP8/10
JA=115°C/W
0.6
0.4
SO
=8 14
8°
C/
W
SO8
JA=110°C/W
QSOP16
JA=112°C/W
0.2
0
0
25
50
75 85 100
125
150
AMBIENT TEMPERATURE (°C)
FIGURE 31. PACKAGE POWER DISSIPATION vs AMBIENT TEMPERATURE
Simplified Schematic Diagram
VS+
I1
I2
Q5
IN+
Q1
R8
VBIAS1
Q6
R3
R1
R7
R6
Q7
R2
Q2
DIFFERENTIAL TO
SINGLE ENDED
DRIVE
GENERATOR
IN-
VBIAS2
Q3
OUT
Q4
Q8
R4
R5
R9
VS-
Description of Operation and Application
Information
Product Description
The EL8202, EL8203 and EL8403 are wide bandwidth, single
supply, low power and rail-to-rail output voltage feedback
operational amplifiers. The amplifiers are internally
compensated for closed loop gain of +1 of greater. Connected
in voltage follower mode and driving a 1k load, the EL8202,
EL8203 and EL8403 have a -3dB bandwidth of 500MHz.
Driving a 150 load, the bandwidth is about 350MHz while
maintaining a 600V/us slew rate. The EL8202 is available with
a power down pin to reduce power to 30µA typically while the
amplifier is disabled.
FN7106 Rev 2.00
April 26, 2006
Input, Output and Supply Voltage Range
The EL8202, EL8203 and EL8403 have been designed to
operate with a single supply voltage from 3V to 5.0V. Split
supplies can also be used as long as their total voltage is
within 3V to 5.0V. The amplifiers have an input common mode
voltage range from 0.15V below the negative supply (VS- pin)
to within 1.5V of the positive supply (VS+ pin). If the input
signal is outside the above specified range, it will cause the
output signal to be distorted.
The output of the EL8202, EL8203 and EL8403 can swing rail
to rail. As the load resistance becomes lower, the ability to
drive close to each rail is reduced. For the load resistor 1k,
the output swing is about 4.9V at a 5V supply. For the load
resistor 150, the output swing is about 4.6V.
Page 10 of 16
EL8202, EL8203, EL8403
Choice of Feedback Resistor and Gain Bandwidth
Product
For applications that require a gain of +1, no feedback resistor
is required. Just short the output pin to the inverting input pin.
For gains greater than +1, the feedback resistor forms a pole
with the parasitic capacitance at the inverting input. As this
pole becomes smaller, the amplifier’s phase margin is reduced.
This causes ringing in the time domain and peaking in the
frequency domain. Therefore, RF has some maximum value
that should not be exceeded for optimum performance. If a
large value of RF must be used, a small capacitor in the few pF
range in parallel with RF can help to reduce the ringing and
peaking at the expense of reducing the bandwidth.
As far as the output stage of the amplifier is concerned, the
output stage is also a gain stage with the load. RF and RG
appear in parallel with RL for gains other than +1. As this
combination gets smaller, the bandwidth falls off.
Consequently, RF also has a minimum value that should not be
exceeded for optimum performance. For gain of +1, RF=0 is
optimum. For the gains other than +1, optimum response is
obtained with RF between 300 to 1k.
The EL8202, EL8203 and EL8403 have a gain bandwidth
product of 200MHz. For gains 5, its bandwidth can be
predicted by the following equation:
Gain BW = 200MHz
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same frequency
response as DC levels are changed at the output. This is
especially difficult when driving a standard video load of 150,
because the change in output current with DC level. Special
circuitry has been incorporated in the EL8202, EL8203 and
EL8403 to reduce the variation of the output impedance with
the current output. This results in dG and dP specifications of
0.01% and 0.01, while driving 150 at a gain of 2. Driving
high impedance loads would give a similar or better dG and dP
performance.
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help to
reduce peaking.
Disable/Power-Down
The EL8202 can be disabled and placed its output in a high
impedance state. The turn off time is about 25ns and the turn
on time is about 200ns. When disabled, the amplifier’s supply
current is reduced to 40µA typically, thereby effectively
eliminating the power consumption. The amplifier’s power
down can be controlled by standard TTL or CMOS signal
levels at the ENABLE pin. The applied logic signal is relative to
VS- pin. Letting the ENABLE pin float or applying a signal that
is less than 0.8V above VS- will enable the amplifier. The
amplifier will be disabled when the signal at ENABLE pin is 2V
above VS-.
Output Drive Capability
The EL8202, EL8203 and EL8403 do not have internal short
circuit protection circuitry. They have a typical short circuit
current of 80mA sourcing and 150mA sinking for the output is
connected to half way between the rails with a 10 resistor. If
the output is shorted indefinitely, the power dissipation could
easily increase such that the part will be destroyed. Maximum
reliability is maintained if the output current never exceeds
±40mA. This limit is set by the design of the internal metal
interconnections.
Power Dissipation
With the high output drive capability of the EL8202, EL8203
and EL8403. It is possible to exceed the 125C absolute
maximum junction temperature under certain load current
conditions. Therefore, it is important to calculate the maximum
junction temperature for the application to determine if the load
conditions or package types need to be modified for the
amplifier to remain in the safe operating area.
The maximum power dissipation allowed in a package is
determined according to:
T JMAX – T AMAX
PD MAX = -------------------------------------------- JA
Driving Capacitive Loads and Cables
The EL8202, EL8203 and EL8403 can drive 5pF loads in
parallel with 1k with less than 5dB of peaking at gain of +1. If
less peaking is desired in applications, a small series resistor
(usually between 5 to 50) can be placed in series with the
output to eliminate most peaking. However, this will reduce the
gain slightly. If the gain setting is greater than 1, the gain
resistor RG can then be chosen to make up for any gain loss
which may be created by the additional series resistor at the
output.
Where:
TJMAX = Maximum junction temperature
TAMAX = Maximum ambient temperature
JA = Thermal resistance of the package
The maximum power dissipation actually produced by an IC is
the total quiescent supply current times the total power supply
voltage, plus the power in the IC due to the load, or:
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier’s output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
FN7106 Rev 2.00
April 26, 2006
Page 11 of 16
EL8202, EL8203, EL8403
For sourcing:
V OUTi
PD MAX = V S I SMAX + V S – V OUTi ----------------R Li
For sinking:
PD MAX = V S I SMAX + V OUTi – V S- I LOADi
video signal applied at the input, as well as the output signal
with the negative going sync pulse removed.
5V
VIN
VS+
+
-
75
VOUT
VS-
75
75
Where:
VS = Total supply voltage
ISMAX = Maximum quiescent supply current
1K
1K
FIGURE 32. SYNC PULSE REMOVER
VOUTi = Maximum output voltage of the application for each
channel
RLOADi = Load resistance tied to ground for each channel
1V
ILOADi = Load current for each channel
By setting the two PDMAX equations equal to each other, we
can solve the output current and RLOADi to avoid the device
overheat.
0V
1V
Power Supply Bypassing and Printed Circuit Board
Layout
As with any high frequency device, a good printed circuit board
layout is necessary for optimum performance. Lead lengths
should be as short as possible. The power supply pin must be
well bypassed to reduce the risk of oscillation. For normal
single supply operation, where the VS- pin is connected to the
ground plane, a single 4.7µF tantalum capacitor in parallel with
a 0.1µF ceramic capacitor from VS+ to GND will suffice. This
same capacitor combination should be placed at each supply
pin to ground if split supplies are to be used. In this case, the
VS- pin becomes the negative supply rail.
For good AC performance, parasitic capacitance should be
kept to a minimum. Use of wire wound resistors should be
avoided because of their additional series inductance. Use of
sockets should also be avoided if possible. Sockets add
parasitic inductance and capacitance that can result in
compromised performance. Minimizing parasitic capacitance
at the amplifier’s inverting input pin is very important. The
feedback resistor should be placed very close to the inverting
input pin. Strip line design techniques are recommended for
the signal traces.
0.5V
VIN
0.5V
VOUT
0V
M = 10µs/DIV
FIGURE 33. VIDEO SIGNAL
MULTIPLEXER
Besides the normal power down usage, the ENABLE pin of the
EL8202 can be used for multiplexing applications. Figure 34
shows two EL8202 with the outputs tied together, driving a
back terminated 75 video load. A 2VP-P 2MHz sine wave is
applied to Amp A and a 1VP-P 2MHz sine wave is applied to
Amp B. Figure 33 shows the ENABLE signal and the resulting
output waveform at VOUT. Observe the break-before-make
operation of the multiplexing. Amp A is on and VIN1 is passed
through to the output when the ENABLE signal is low and turns
off in about 25ns when the ENABLE signal is high. About
200ns later, Amp B turns on and VIN2 is passed through to the
output. The break-before-make operation ensures that more
than one amplifier isn’t trying to drive the bus at the same time.
Typical Applications
VIDEO SYNC PULSE REMOVER
Many CMOS analog to digital converters have a parasitic latch
up problem when subjected to negative input voltage levels.
Since the sync tip contains no useful video information and it is
a negative going pulse, we can chop it off. Figure 32 shows a
gain of 2 connections. Figure 33 shows the complete input
FN7106 Rev 2.00
April 26, 2006
Page 12 of 16
EL8202, EL8203, EL8403
+2.5V
B 2MHz
1VP-P
5V
+
75
-2.5V
VIN
C1
47µF
R1
10K
R3
C3
470µF 75
+
1K
1K
75
VOUT
RT
75
VOUT
-
R2
10K
75
+2.5V
A 2MHz
2VP-P
75
+
RF
1k
RG
1k
-
75
-2.5V
1K
C2
220µF
1K
FIGURE 36. 5V SINGLE SUPPLY NON INVERTING
VIDEO LINE DRIVER
ENABLE
RF
1k
FIGURE 34. TWO TO ONE MULTIPLEXER
VIN
0V
-0.5V
ENABLE
-1.5V
C1
RG
47µF 500
5V
RT
75
5V
-
R3
C3
470µF 75
VOUT
+
R1
10K
75
-2.5V
R2
10K
1V
C2
220µF
0V
B
A
-1V
FIGURE 37. SINGLE SUPPLY INVERTING VIDEO LINE DRIVER
4
M = 50ns/DIV
SINGLE SUPPLY VIDEO LINE DRIVER
The EL8202, EL8203 and EL8403 are wideband rail-to-rail
output op amplifiers with large output current, excellent dG, dP,
and low distortion that allow them to drive video signals in low
supply applications. Figure 36 is the single supply noninverting video line driver configuration and Figure 37 is the
inverting video ling driver configuration. The signal is AC
coupled by C1. R1 and R2 are used to level shift the input and
output to provide the largest output swing. RF and RG set the
AC gain. C2 isolates the virtual ground potential. RT and R3
are the termination resistors for the line. C1, C2 and C3 are
selected big enough to minimize the droop of the luminance
signal.
FN7106 Rev 2.00
April 26, 2006
3
NORMALIZED GAIN (dB)
FIGURE 35.
2
1
0
AV = 2
-1
-2
AV = -2
-3
-4
-5
-6
100K
1M
10M
FREQUENCY (Hz)
100M 500M
FIGURE 38. VIDEO LINE DRIVER FREQUENCY RESPONSE
Page 13 of 16
EL8202, EL8203, EL8403
SO Package Outline Drawing
FN7106 Rev 2.00
April 26, 2006
Page 14 of 16
EL8202, EL8203, EL8403
MSOP Package Outline Drawing
FN7106 Rev 2.00
April 26, 2006
Page 15 of 16
EL8202, EL8203, EL8403
QSOP Package Outline Drawing
NOTE: The package drawing shown here may not be the latest version. To check the latest revision, please refer to the Intersil website at
http://www.intersil.com/design/packages/index.asp
© Copyright Intersil Americas LLC 2003-2006. All Rights Reserved.
All trademarks and registered trademarks are the property of their respective owners.
For additional products, see www.intersil.com/en/products.html
Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted
in the quality certifications found at www.intersil.com/en/support/qualandreliability.html
Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such
modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are
current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its
subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
FN7106 Rev 2.00
April 26, 2006
Page 16 of 16