HA12222F

HA12216F/HA12221F Series Audio Signal Processor for Car Deck (Decode only Dolby B type NR with PB Amp.) REJ03F0132-0600 (Previous: ADE-207-254E) Rev.6.00 Jun 15, 2005 Description HA12216F/HA12221F series are silicon monolithic bipolar IC providing Dolby B type noise reduction, music sensor, PB equalizer system in one chip. Notes: 1. Dolby is a trademark of Dolby Laboratories Licensing Corporation. A license from Dolby Laboratories Licensing Corporation is required for the use of this IC. 2. HA12221F series does not include Dolby B NR. Functions • • • • PB equalizer Music sensor Dolby B NR (Only HA12216F series) Line mute (Tape radio) SW × 2 channel × 1 channel × 2 channel × 2 channel Features • Different type of PB equalizer characteristics selection (120 µs/70 µs) is available with fully electronic control switching built-in. • Changeable to Forward, Reverse-mode for PB head with fully electronic control switching built-in. • Available to change music sensing level by external resistor. • Available to change response of music sensor by external capacitor. • Music sensing level, built-in switch to change a band (MSGV). • NR ON/OFF fully electronic control switching built-in. (Only HA12216F series) • Line mute (Tape radio) control switching built-in. • Available to connect direct with MPU. • These ICs are strong for a cellular phone noise. (18 dB improvement from HA12163) Rev.6.00 Jun 15, 2005 page 1 of 52 HA12216F/HA12221F Series Ordering Information Operating Voltage Product HA12216F/HA12221F HA12217F/HA12222F HA12218F/HA12223F Min 6.5 6.8 7.2 12 12 12 Max V V V Unit Notes: 1. These ICs are designed to operate on single supply. 2. HA12217F and HA12218F, HA12222F and HA12223F are develop, there meets comply with your demands. Standard Level Product HA12216F/HA12221F HA12217F/HA12222F HA12218F/HA12223F Package Code (Previous Code) PLQP0040JB-A (FP-40B) PLQP0040JB-A (FP-40B) PLQP0040JB-A (FP-40B) PB-OUT Level 300 mVrms 387.5 mVrms 450 mVrms Function Product HA12216F series HA12221F series PB-EQ ❍ ❍ ❍ ❍ Music Sensor ❍ ❍ Mute ❍ × Dolby B NR Parallel-Data Format 10 11* 12 13 14 Note: Pin Name TAPE/RADIO NR ON/OFF 120 µ/70 µ Forward/Reverse Search/Repeat Non connection regarding HA12221F series. Pin No. Lo TAPE NR OFF 120 µ (Normal) Forward Search (FF or REV) Hi RADIO NR ON 70 µ (Metal or Chrome) Reverse Repeat (Normal Speed) Rev.6.00 Jun 15, 2005 page 2 of 52 HA12216F/HA12221F Series Pin Description, Equivalent Circuit (VCC = 9 V, A system of single supply voltage, Ta = 25°C, No Signal, The value in the show typical value.) Pin No. 18 Terminal Name MSI Note V = VCC/2 Equivalent Circuit Pin Description MS input * 1 V 100k VCC/2 28 3 26 5 23 *2 TAI (L) TAI (R) RAI (L) RAI (R) DET (L) Tape input Radio input (Mute) V = 2.5V VCC Time constant pin for rectifier V GND 8 *2 33 4 *2 DET (R) RIP Bias V = VCC/2 V = 0.28V V GND Ripple filter Dolby bias current input 17 MSDET — Time constant pin for rectifier GND Notes: 1. MS: Music Sensor 2. Non connection regarding HA12221F series. Rev.6.00 Jun 15, 2005 page 3 of 52 HA12216F/HA12221F Series Pin Description, Equivalent Circuit (cont.) (VCC = 9 V, A system of single supply voltage, Ta = 25°C, No Signal, The value in the show typical value.) Pin No. 25 Terminal Name PBOUT (L) Note V = VCC/2 Equivalent Circuit VCC Pin Description PB output V GND 6 19 PBOUT (R) MAOUT V = VCC/2 VCC MS amp. output *1 V GND 38 29 2 30 VREF EQOUT (L) EQOUT (R) M-OUT (L) Reference output Equalizer output (120µ) V = VCC/2 V VCC Equalizer output (70µ) GND 1 16 7 9 22 24 27 Note: M-OUT (R) VCC NC — — Power supply No connection 1. MS: Music Sensor Rev.6.00 Jun 15, 2005 page 4 of 52 HA12216F/HA12221F Series Pin Description, Equivalent Circuit (cont.) (VCC = 9 V, A system of single supply voltage, Ta = 25°C, No Signal, The value in the show typical value.) Pin No. 34 Terminal Name FIN (L) Note — Equivalent Circuit Pin Description Equalizer intput (Forward) V 37 32 39 31 40 10 FIN (R) RIN (L) RIN (R) NFI (L) NFI (R) T/R (Mute) — Equalizer intput (Reverse) Negative feedback Mode control input 22 k 100 k GND 11 * 12 13 14 15 2 NR ON/OFF 120/70 F/R S/R (MS GV) MSOUT — I MS VCC MS output (to MPU) * 1 200 100k D GND 20 MS GV (R) V = VCC/2 MS gain terminal * 1 V 90k 21 MS GV (S) GND pin 35 GND — 36 Notes: 1. MS: Music Sensor 2. Non connection regarding HA12221F series. Rev.6.00 Jun 15, 2005 page 5 of 52 HA12216F/HA12221F Series Block Diagram HA12216F Series PBOUT (L) NC 27 NC 24 NC 22 30 29 120/70 − 31 + 28 26 25 23 21 20 19 18 + + 32 + F/R T/R Dolby B NR 33 RIP 34 35 GND 36 GND 37 38 Vref 39 + − S/R DET 17 16 15 14 13 MSOUT S/R (MS GV) F/R 120/70 NR ON/OFF LPF − + VCC F/R − + T/R Dolby B NR 12 11 40 120/70 1 2 3 BIAS 4 5 6 7 NC 8 9 NC 10 PBOUT (R) T/R (Mute) Rev.6.00 Jun 15, 2005 page 6 of 52 HA12216F/HA12221F Series HA12221F Series PBOUT (L) 30 29 120/70 − 31 + 28 NC 27 26 25 NC 24 NC 23 NC 22 21 20 + + 32 + F/R T/R 19 18 33 RIP 34 35 GND 36 GND 37 38 Vref 39 + − S/R DET 17 16 15 14 13 MSOUT S/R (MS GV) F/R 120/70 LPF − + VCC F/R − + T/R 12 11 NC 40 120/70 1 2 3 4 NC 5 6 7 NC 8 NC 9 NC 10 PBOUT (R) T/R (Mute) Rev.6.00 Jun 15, 2005 page 7 of 52 HA12216F/HA12221F Series Functional Description Power Supply Range HA12216F/HA12221F series are provided with three line output level, which will permit on optimum overload margin for power supply conditions. And these are designed to operate on single supply only. Table 1 Supply Voltage Range Product HA12216F/HA12221F HA12217F/HA12222F HA12218F/HA12223F 6.5 V to 12.0 V 6.8 V to 12.0 V 7.2 V to 12.0 V Single Supply Note: The lower limit of supply voltage depends on the line output reference level. The minimum value of the overload margin is specified as 12 dB by Dolby Laboratories. Reference Voltage These devices provide the reference voltage of half the supply voltage that is the signal grounds. As the peculiarity of these devices, the capacitor for the ripple filter is very small about 1/100 compared with their usual value. The block diagram is shown as figure 1. 16 VCC + − MS block + − 38 VREF EQ block (to Line Amp. in case of HA12221F series) 35 36 33 RIP + + − + − L channel Dolby NR circuit R channel Dolby NR circuit : Internal reference voltage C15 1µ Note: HA12221F series does not include Dolby NR circuit. Figure 1 The Block Diagram of Reference Supply Voltage Rev.6.00 Jun 15, 2005 page 8 of 52 HA12216F/HA12221F Series Operating Mode Control HA12216F/HA12221F series provides fully electronic switching circuits. And each operating mode control are controlled by parallel data (DC voltage). When a power supply of this IC is cut off, for a voltage, in addition to a mode control terminal even though as do not destruct it, in series for resistance. Table 2 Threshold Voltage (VTH) Lo –0.2 to 1.0 Hi 3.5 to VCC Unit V Test Condition Input Pin Measure V Pin No. 10, 11*, 12, 13, 14 Note: * Non connection regarding HA12221F series. Table 3 10 11* 12 13 14 Switching Truth Table Pin No. TAPE NR OFF 120 µ (Normal) FORWARD SER (FF or REV) Lo RADIO NR ON 70 µ (Metal or Chrome) REVERSE REP (Normal Speed) Hi Notes: * Non connection regarding HA12221F series. 1. Each pins are on pulled down with 100 kΩ internal resistor. Therefore, it will be low-level when each pins are open. 2. Over shoot level and under shoot level of input signal must be the standardized. (High: VCC, Low: –0.2 V) 3. Reducing pop noise is so much better for 10 kΩ to 22 kΩ resisitor and 1 µF to 22 µF capacitor shown figure 2. Input Pin 10 to 22kΩ + MPU 1 to 22µF Figure 2 Interface for Reduction of Pop Noise Rev.6.00 Jun 15, 2005 page 9 of 52 HA12216F/HA12221F Series Input Block Diagram and Level Diagram PBOUT HA12216F/HA12221F: 300mVrms (−8.2dB) HA12217F/HA12222F: 387.5mVrms (−6.0dB) HA12218F/HA12223F: 450mVrms (−4.7dB) R6 5.1kΩ R5 5.1kΩ R2 330kΩ C1 0.01µF R4 12kΩ R3 18kΩ C2 0.1µF EQOUT M-OUT NFI RIN VREF FIN −+ TAI RAI 30mVrms 42.4mVrms (−28.2dBs) (−25.2dBs) EQ Amp. Input Amp. + − R1 180Ω Dolby NR circuit * PBOUT 0.6mVrms (−62.2dBs) The each level shown above is typical value when offering PBOUT level to PBOUT pin. (EQ Amp. GV = 40dB, f = 1kHz) Note: HA12221F series does not include Dolby NR circuit. Figure 3 Input Block Diagram Adjustment of Playback Reference Operate Level After replace R5 and R6 with a half-fix volume of 10 kΩ, adjust playback reference operate level. Rev.6.00 Jun 15, 2005 page 10 of 52 HA12216F/HA12221F Series The Sensitivity Adjustment of Music Sensor Adjusting MS Amp. gain by external resistor, the sensitivity of music sensor can set up. The music sensor block diagram is shown in figure 4, and frequency response is shown in figure 5. VCC CEX2 REX2 28 ×1 TAI (L) +CEX1 DVCC + C6 REX1 C8 0.01µF R11 330kΩ 0.33µF 21 20 MS MS SER REP 90kΩ − + 19 18 MA MSI OUT 17 MS DET RL MSOUT 15 GND 36 35 −6dB L⋅R signal addition circuit + − LPF 25kHz MS Amp. DET 100kΩ Micro computer 20dB ×1 3 TAI (R) Figure 4 Music Sensor Block Diagram GV2 f3 Repeat mode (REP) f4 GV (dB) GV1 f1 Search mode (SER) f2 10 100 1k f (Hz) 10k 25k 100k Figure 5 Frequency Response Rev.6.00 Jun 15, 2005 page 11 of 52 HA12216F/HA12221F Series 1. Serch mode GV1 = 20dB + 20log 1 + 90k [dB] REX2 1 f1 = [Hz], f2 = 25k [Hz] 2π ⋅ CEX2 ⋅ REX2 2. Repeat mode GV2 = 20dB + 20log 1 + 90k [dB] REX1 1 f3 = [Hz], f4 = 25k [Hz] 2π ⋅ CEX1 ⋅ REX1 GVIA: L·R signal addition circuit gain. The sensitivity of music sensor (S) is computed by the formula mentioned below. 3 S = − GV*1 − 20log 130* = 12.7 − GV 30*2 [dB] Note: 1. Search mode: GV1, Repeat mode: G V2 2. Standard level of TAI pin (Dolby level correspondence) = 30 mVrms 3. Standard sensing level of music sensor = 130 mVrms S (one side channel) –14.8 dB –33.0 dB S (both channel) –20.8 dB –39.0 dB Item Search mode Repeat mode REX1, 2 24 kΩ 2.4 kΩ CEX1, 2 0.01 µF 1 µF GV1, 2 33.5 dB 51.7 dB f1, 3 663 Hz 66.3 Hz f2, 4 25 kHz 25 kHz Note: S is 6 dB down in case of one-side channel. And this MS presented hysteresis lest MSOUT terminal should turn over again Hi level or Lo level, in case of thresh S level constantly. Music Sensor Time Constant 1. Sensing no signal to signal (Attack) is determined by C6, 0.01 µF to 1 µF capacitor C6 can be applicable. 2. Sensing signal to no signal (Recovery) is determined by C6 and R11, however preceding (1), 100 kΩ to 1 MΩ can be applicable. Music Sensor Output (MSOUT) As for the internal circuit of music sensor block, music sensor output pin is connected to the collector of NPN type directly, therefore, output level will be “high” when sensing no signal. And output level will be “low” when sensing signal. IL = DVCC − MSOUTLO* RL * MSOUTLO : Sensing signal (about 1V) Note: 1. Supply voltage of MSOUT pin must be less than VCC voltage. Rev.6.00 Jun 15, 2005 page 12 of 52 HA12216F/HA12221F Series The Tolerances of External Components for Dolby NR (Only HA12216F Series) For adequate Dolby NR tracking response, take external components shown below. Also, leak is small capacity, and please employ a good quality object. C10 0.1µF ±10% 23 DET (L) HA12216F Series BIAS 4 R8 18kΩ ±2% DET (R) 8 C4 0.1µF ±10% Figure 6 Tolerance of External Components Countermeasure of a Cellular Phone Noise This IC have reinforced a cellular phone noise countermeasure, to show it hereinafter. However, it is presumed that this effect change it greatly, by a mount set. Please sufficiently examine an arrangement of positions, shield method, wiring pattern, in order to oftain a maximum effect. A high terminal of a noise sensitivity of this IC is FIN, RIN, NFI and RIP. ref HA12216F 1000p 680 FIN NFI 330k 0.01µ 180 + − SG EQOUT AC VM wait DIN/AUDIO 12k Note: Test condition • Use for SG by cellular radio for an evaluation use. • SG output mode PDC system, burst UP Tch (Transmission mode on the side of a movement machine) • To evaluate a capacitor of 1000 pF as connecting with it directly. • About EQOUT output, what you measure through DIN/AUDIO filter. Figure 7 Test Circuit Rev.6.00 Jun 15, 2005 page 13 of 52 HA12216F/HA12221F Series 10 Vin = 0dBm, VCC = 9V, Fin Lch HA12216 & HA12221 HA12163 series HA12192 series 0 EQOUT Noise Output (dBs) −10 −20 −30 −40 −50 −60 100 1000 Frequency (MHz) 10000 Figure 8 EQOUT Noise Output vs. Transmission Frequency Characteristic 10 0 VCC = 9V, Fin Lch HA12216 & HA12221 HA12163 series HA12192 series EQOUT Noise Output (dBs) DIN/AUDIO −10 −20 −30 −40 −50 −60 −70 −80 −50 −40 −30 −20 −10 0 Higher Harmonic Input Vin (dBm) 10 20 Figure 9 EQOUT Noise Output vs. Transmission Rev.6.00 Jun 15, 2005 page 14 of 52 HA12216F/HA12221F Series Absolute Maximum Ratings (Ta = 25°C) Item Maximum supply voltage Power dissipation Operating temperature Storage temperature Symbol VCC Max Pd Topr Tstg Rating 16 400 –40 to +85 –55 to +125 V mW °C °C Unit Note Ta ≤ 85°C Rev.6.00 Jun 15, 2005 page 15 of 52 (Ta = 25°C, VCC = 9.0 V, PBOUT Level 300 mVrms(HA12216F) 387.5 mVrms(HA12217F) 450 mVrms(HA12218F)) Test Condition IC Condition Input Output Remark HA12216F Series Application Terminal R  6 L  25 HA12216F/HA12221F Series Electrical Characteristics Rev.6.00 Jun 15, 2005 page 16 of 52 16 Item Symbol Quiescent current IQ Input Amp. HA12216F GVIA TAI gain GVIA RAI HA12217F GVIA TAI GVIA RAI HA12218F GVIA TAI GVIA RAI DEC-2k (1) B-type decode cut DEC-2k (2) DEC-5k (1) DEC-5k (2) Min 4.0 18.8 15.8 21.2 18.2 22.5 19.5 2.8 7.0 1.7 6.7 6 NR 120µ/ ON/OFF 70µ ON 70µ OFF  OFF  OFF  OFF  OFF  OFF   ON  ON  ON  ON PBOUT fin F/R T/R S/R Input Output (Hz) level (dB)    No signal F  T S 0  T  TAI PBOUT 1k 0  R  RAI PBOUT 1k 0  T  TAI PBOUT 1k  R  RAI PBOUT 1k 0  T  TAI PBOUT 1k 0  R  RAI PBOUT 1k 0 −20  T  TAI PBOUT 2k −30 T  TAI PBOUT 2k  −20 T  TAI PBOUT 5k  −30 T  TAI PBOUT 5k  Typ 9.5 19.8 16.8 22.2 19.2 23.5 20.5 4.3 8.5 3.2 8.2 Max Unit 15.0 mA 20.8 dB 17.8 23.2 20.2 24.5 21.5 5.8 dB 10.0 4.7 9.7 R  3 5 3 5 3 5 3 L  28 26 28 26 28 26 28 25 PBOUT offset Signal handling Signal to noise ratio T.H.D. Channel separation 25 25 25 25 25→6 1 Crosstalk 25 29 PB-EQ gain Vofs Vo max S/N THD CT RL (1) CT RL (2) CT EQ→RAI CT RAI→EQ GV EQ 1k GV EQ 10k(1) GV EQ 10k(2) OFF ON ON ON OFF OFF OFF OFF         120µ 120µ 120µ 120µ 120µ 70µ   (0) 0 (+12) (+12) (+12) (+12)     T↔R   PBOUT   T  TAI PBOUT 1k  T  TAI PBOUT (1k)  T  TAI PBOUT 1k  R  RAI PBOUT 1k F T  FIN PBOUT 1k F T→R  FIN PBOUT 1k F R→T  RAI PBOUT 1k F/R   FIN/RIN EQOUT 1k   FIN EQOUT 10k F   FIN EQOUT 10k F VCC=12V, No signal −150 THD=1% 12.0 Rg=10kΩ, CCIR/ARM 70.0  70.0 50.0 70.0 50.0 Vin=0.6mVrms 37.0 33.0 29.0 0.0 13.0 80.0 0.05 80.0 60.0 80.0 60.0 40.0 36.0 32.0 150 mV 28 6 3 dB  6 3 28 dB (3) (28) 6  0.3 % 6 3 28 dB  3 28 6→25  37 34 dB 37 34  6  26 5 43.0 dB 37/39 34/32 2 39.0 37 34 35.0 37 34 1 PB-EQ Max output level PB-EQ THD Noise level converted in input MS sensitivity level 29 29 29 29 15 15  15   10 to 14 MS output low level MS output leak current Control voltage VOM THD-EQ VN VON (1) VON (2) VOL IOH VIL VIH          F/R F/R F/R       120µ 120µ 120µ          T T T     FIN EQOUT 1k  FIN/RIN EQOUT 1k  FIN/RIN EQOUT (1k) R TAI PBOUT 5k S TAI PBOUT 5k S TAI MSOUT 5k   MSOUT               0    300 THD=1% Vin=3mVrms  Rg=680Ω, DIN-AUDIO  −36 −18  No signal  −0.2 3.5 600  mVrms 37/39 34/32 2 0.1 0.3 % 37/39 34/32 2 0.7 1.5 µVrms (37/39)(34/32) 2 2 28 3 −32 −28 dB −14 −10 V 28  1.0 1.5 3  0.0 2.0 µA  V    1.0  VCC Νοτε: 1. HA12216F: VCC = 6.5V HA12217F: VCC = 6.8V HA12218F: VCC = 7.2V HA12221F Series (Ta = 25°C, VCC = 9.0 V, PBOUT Level 300 mVrms(HA12221F) 387.5 mVrms(HA12222F) 450 mVrms(HA12223F)) Test Condition IC Condition Application Terminal Input Output Remark HA12216F/HA12221F Series Rev.6.00 Jun 15, 2005 page 17 of 52 120µ/ 70µ 70µ       PBOUT fin F/R T/R S/R Input Output (Hz) level (dB)   T S F No signal   0  T  TAI PBOUT 1k 0  R  RAI PBOUT 1k 0  T  TAI PBOUT 1k  R  RAI PBOUT 1k 0  T  TAI PBOUT 1k 0  R  RAI PBOUT 1k 0 Item Symbol Quiescent current IQ Input Amp. HA12221F GVIA TAI gain GVIA RAI HA12222F GVIA TAI GVIA RAI HA12223F GVIA TAI GVIA RAI Min Typ 3.0 5.0 19.0 20.0 16.0 17.0 21.2 22.2 18.2 19.2 22.5 23.5 19.5 20.5 20.2 24.5 21.5 Max Unit 8.0 mA 21.0 dB 18.0 23.2 R  3 5 3 5 3 5 L  28 26 28 26 28 26 R  6 L  25 16 PBOUT offset Signal handling Signal to noise ratio T.H.D. Channel separation 1 Crosstalk PB-EQ gain Vofs Vo max S/N THD CT RL (1) CT RL (2) CT EQ→RAI CT RAI→EQ GV EQ 1k GV EQ 10k(1) GV EQ 10k(2)      120µ 120µ 120µ 120µ 120µ 70µ  T↔R T T T R F T F T→R F R→T F/R  F F   PBOUT   TAI PBOUT 1k  TAI PBOUT (1k)  TAI PBOUT 1k  RAI PBOUT 1k  FIN PBOUT 1k  FIN PBOUT 1k  RAI PBOUT 1k  FIN/RIN EQOUT 1k  FIN EQOUT 10k  FIN EQOUT 10k   (0) 0 (+12) (+12) (+12) (+12)    VCC=12V, No signal −150 THD=1% 12.0 Rg=10kΩ, CCIR/ARM 70.0  70.0 50.0 70.0 50.0 Vin=0.6mVrms 37.0 33.0 29.0 0.0 13.0 80.0 0.05 80.0 60.0 80.0 60.0 40.0 36.0 32.0 150 mV 28 6 25 3 dB 25 6  3 28 dB (3) (28) 25 6  25 6 0.3 % 3 28 dB  3 28 6→25 25→6  37 34 dB  25 37 6 34  5 26 43.0 dB 37/39 34/32 2 29 39.0 37 34 35.0 37 34 1 PB-EQ Max output level PB-EQ THD Noise level converted in input MS sensitivity level 29 29 29 29 15 15  15   10 to 14 MS output low level MS output leak current Control voltage VOM THD-EQ VN VON (1) VON (2) VOL IOH VIL VIH 120µ 120µ 120µ       F/R F/R F/R          T T T     FIN EQOUT 1k  FIN/RIN EQOUT 1k  FIN/RIN EQOUT (1k) TAI PBOUT 5k R S TAI PBOUT 5k TAI MSOUT 5k S  MSOUT                0    300 THD=1% Vin=3mVrms  Rg=680Ω, DIN-AUDIO  −36 −18  No signal  −0.2 3.5 600  mVrms 37/39 34/32 2 0.1 0.3 % 37/39 34/32 2 0.7 1.5 µVrms (37/39) (34/32) 2 2 28 3 −32 −28 dB −14 −10 V  28 3 1.0 1.5    0.0 2.0 µA V     1.0  VCC Note: 1. HA12221F: VCC = 6.5V HA12222F: VCC = 6.8V HA12223F: VCC = 7.2V HA12216F/HA12221F Series Test Circuit HA12216F Series EQOUT (L) R19 10k R20 5.1k R22 12k R24 330k R25 180 + PBOUT (L) R29 10k C24 0.47µ + RAI (L) TAI (L) RIN (L) + 33 RIP 34 35 GND 36 GND + − − + 18 DET 17 16 MSOUT 15 FIN (L) C21 22µ C20 1µ R27 680 C22 100µ LPF C10 0.33µ MSOUT R14 3.9k SW5 FIN (R) C1 22µ + R1 680 37 38 Vref 39 F/R − + S/R (MS Gv) 14 F/R 13 T/R Dolby B NR 120/70 12 SW4 SW3 R13 22k SW2 RIN (R) C2 22µ R2 680 R3 180 R4 330k 40 C3 0.01µ 120/70 1 R5 18k R6 12k 2 3 BIAS 4 5 R10 NR ON/OFF 11 + 6 + + 7 NC C6 2.2µ R11 10k 8 C4 18k R7 0.1µ 5.1k + C5 R8 0.47µ 5.1k R9 10k R28 10k 9 NC C7 0.1µ C9 22µ 10 TAP/RAD (Mute) R12 22k + SW1 C8 22µ C23 0.47µ TAI (R) RAI (R) EQOUT (R) Note: 1. Resistor tolerance ±1% 2. Capacitor tolerance ±1% 3. Unit R: Ω, C: F PBOUT (R) Rev.6.00 Jun 15, 2005 page 18 of 52 + C19 22µ + + R26 680 32 + F/R T/R Dolby B NR 20 19 C11 0.01µ R15 330k + VCC DVCC GND R23 C18 18k 30 29 0.01µ 120/70 − 31 28 NC 27 26 25 + + R21 5.1k C17 0.1µ C16 0.47µ R18 10k C15 2.2µ NC 24 23 C14 0.1µ NC 22 21 C3 0.01µ R17 24k R16 C12 2.4k 1µ + HA12216F/HA12221F Series HA12221F Series EQOUT (L) R19 10k R20 5.1k R22 12k R24 330k R25 180 + PBOUT (L) R29 10k C24 0.47µ + RAI (L) TAI (L) 20 T/R 19 18 DET 17 − + RIN (L) + 33 RIP 34 35 GND 36 GND + − FIN (L) C21 22µ C20 1µ R27 680 C22 100µ 16 MSOUT 15 LPF C10 0.33µ MSOUT R14 3.9k SW5 FIN (R) C1 22µ + R1 680 37 38 Vref 39 F/R − + S/R (MS Gv) 14 F/R 13 T/R 120/70 12 NC 11 2 3 4 NC 5 6 + + SW4 SW3 RIN (R) C2 22µ R2 680 R3 180 R4 330k 40 C3 0.01µ 120/70 1 R5 18k R6 12k 7 NC C6 2.2µ R11 10k 8 NC 9 NC 10 C4 R7 0.1µ 5.1k + C5 R8 0.47µ 5.1k R9 10k R28 10k TAP/RAD (Mute) R12 22k + SW1 C8 22µ C23 0.47µ TAI (R) RAI (R) EQOUT (R) Note: 1. Resistor tolerance ±1% 2. Capacitor tolerance ±1% 3. Unit R: Ω, C: F PBOUT (R) Rev.6.00 Jun 15, 2005 page 19 of 52 + C19 22µ + + R26 680 32 + F/R C11 0.01µ R15 330k + VCC DVCC GND R23 C18 18k 30 29 0.01µ 120/70 − 31 28 NC 27 26 25 + + R21 5.1k C17 0.1µ C16 0.47µ R18 10k C15 2.2µ NC 24 NC 23 NC 22 21 C3 0.01µ R17 24k R16 C12 2.4k 1µ + HA12216F/HA12221F Series Characteristic Curves Quiescent Current vs. Supply Voltage (HA12216F) 11 all low 70µ (Other switch is all low) NR-ON VCC = 9.0V NO SIGNAL Quiescent Current IQ (mA) 10 9 8 6 7 8 9 10 11 Supply Voltage (V) 12 13 Input Amp. Gain vs. Frequency (HA12216F) 26 VCC = 9.0V TAI →PBOUT RAI NR-OFF TAI 22 Gain (dB) 18 RAI 14 10 6 10 100 1k 10k Frequency (Hz) 100k 1M Rev.6.00 Jun 15, 2005 page 20 of 52 HA12216F/HA12221F Series Decode Cut vs. Frequency (HA12216F) 0 0dB −2 −10dB Decode Cut (dB) −4 −20dB −6 −30dB −8 −10 −12 100 VCC = 9.0V TAI→PBOUT NR-ON −40dB 1k Frequency (Hz) 10k 20k Total Harmonic Distortion vs. Frequency (HA12216F) (1) 1 0dB 10dB −10dB VCC = 9.0V TAI→PBOUT NR-OFF T.H.D. (%) 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 400Hz HPF + 80kHz LPF 1k Frequency (Hz) 10k 20k Rev.6.00 Jun 15, 2005 page 21 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Frequency (HA12216F) (2) 1 0dB 10dB −10dB VCC = 9.0V TAI→PBOUT NR-ON T.H.D. (%) 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 400Hz HPF + 80kHz LPF 1k Frequency (Hz) 10k 20k Total Harmonic Distortion vs. Frequency (HA12216F) (3) 1 0dB 10dB −10dB VCC = 9.0V RAI→PBOUT NR-OFF T.H.D. (%) 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 400Hz HPF + 80kHz LPF 1k Frequency (Hz) 10k 20k Rev.6.00 Jun 15, 2005 page 22 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Output Level (HA12216F) (1) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 1 NR-OFF T.H.D. (%) 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 Total Harmonic Distortion vs. Output Level (HA12216F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 1 NR-ON T.H.D. (%) 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 Rev.6.00 Jun 15, 2005 page 23 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Output Level (HA12216F) (3) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V RAI→PBOUT 0dB = 300mVrms 1 NR-OFF T.H.D. (%) 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 Total Harmonic Distortion vs. Supply Voltage (HA12216F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) TAI→PBOUT = 300mVrms NR-OFF 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 24 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Supply Voltage (HA12216F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) TAI→PBOUT = 300mVrms NR-ON 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Total Harmonic Distortion vs. Supply Voltage (HA12216F) (3) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) RAI→PBOUT = 300mVrms NR-OFF 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 25 of 52 HA12216F/HA12221F Series Signal Handling (HA12216F) 40 35 30 25 20 15 10 5 0 6 TAI NR-OFF TAI NR-ON RAI NR-OFF TAI →PBOUT = 300mVrms RAI f = 1kHz T.H.D. = 1% Vomax (dB) 7 8 9 10 11 12 13 Supply Voltage (V) 14 15 16 Signal to Noise Ratio vs. Supply Voltage (HA12216F) 90 85 Signal to Noise Ratio (dB) 80 75 TAI NR-OFF TAI NR-ON RAI NR-OFF 70 TAI →PBOUT = 300mVrms RAI f = 1kHz CCIR/ARM filter 65 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 26 of 52 HA12216F/HA12221F Series Equalizer Amp. Gain vs. Frequency (HA12216F) 70 60 50 EQ Gain (dB) 40 30 120µ 70µ 20 10 0 −10 10 VCC = 9.0V FIN→EQOUT 100 1k 10k Frequency (Hz) 100k 1M Total Harmonic Distortion vs. Frequency (HA12216F) 1 120µ 70µ VCC = 9.0V FIN→EQOUT 0dB = 60mVrms Vout = +20dB T.H.D. (%) 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 400Hz HPF + 80kHz LPF 1k Frequency (Hz) 10k 20k Rev.6.00 Jun 15, 2005 page 27 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Output Level (HA12216F) (1) 10 1 T.H.D. (%) 0.1 0.01 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 0dB = 60mVrms 120µ 0.001 −5 0 5 10 15 20 25 Output Level Vout (dB) 30 35 Total Harmonic Distortion vs. Output Level (HA12216F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 1 0dB = 60mVrms 70µ T.H.D. (%) 0.1 0.01 0.001 −5 0 5 10 15 20 25 Output Level Vout (dB) 30 35 Rev.6.00 Jun 15, 2005 page 28 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Supply Voltage (HA12216F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms Vout = +20dB 120µ 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Total Harmonic Distortion vs. Supply Voltage (HA12216F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms Vout = +20dB 70µ 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 29 of 52 HA12216F/HA12221F Series Signal Handling (HA12216F) 45 FIN 120µ FIN 70µ RIN 120µ RIN 70µ FIN →EQOUT RIN 0dB = 60mVrms f = 1kHz T.H.D. = 1% 40 35 Vomax (dB) 30 25 20 15 6 8 10 12 Supply Voltage (V) 14 16 Signal to Noise Ratio vs. Supply Voltage (HA12216F) 80 75 70 65 60 55 50 45 40 5 120µ 70µ FIN→EQOUT 0dB = 60mVrms f = 1kHz DIN-AUDIO filter Signal to Noise Ratio (dB) 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 30 of 52 HA12216F/HA12221F Series Ripple Rejection Ratio vs. Frequency (HA12216F) (1) 20 VCC = 9.0V Vin = 100mVrms PBOUT Ripple Rejection Ratio R.R.R. (dB) 0 −20 PBOUT (TAI) NR-OFF −40 PBOUT (TAI) NR-ON PBOUT (RAI) NR-OFF −60 10 100 1k Frequency (Hz) 10k 100k Ripple Rejection Ratio vs. Frequency (HA12216F) (2) 20 VCC = 9.0V Vin = 100mVrms EQOUT FOR mode Ripple Rejection Ratio R.R.R. (dB) 0 −20 EQOUT 120µ −40 EQOUT 70µ −60 10 100 1k Frequency (Hz) 10k 100k Rev.6.00 Jun 15, 2005 page 31 of 52 HA12216F/HA12221F Series Channel Separation vs. Frequency (HA12216F) (1) VCC = 9.0V FIN→PBOUT 0dB = 300mVrms Vout = +12dB −30 −40 Channel Separation (dB) −50 −60 R→L L→R −70 −80 10 100 1k Frequency (Hz) 10k 100k −10 −30 Channel Separation vs. Frequency (HA12216F) (2) VCC = 9.0V RAI→PBOUT Vin = +12dB Channel Separation (dB) −50 −70 −90 −110 R→L L→R −130 10 100 10k 1k Frequency (Hz) 100k 1M Rev.6.00 Jun 15, 2005 page 32 of 52 HA12216F/HA12221F Series Crosstalk (FIN→RAI) vs. Frequency (HA12216F) FIN RIN VCC = 9.0V 0dB = 300mVrms Vout = +12dB −50 −60 Crosstalk (dB) −70 −80 −90 −100 10 100 10k 1k Frequency (Hz) 100k 1M −20 −30 −40 −50 VCC = 9.0V PBOUT Vin = +12dB Crosstalk (mode) vs. Frequency (HA12216F) RAI→TAI Crosstalk (dB) −60 −70 −80 −90 −100 −110 −120 10 100 1k Frequency (Hz) TAI→RAI 10k 100k Rev.6.00 Jun 15, 2005 page 33 of 52 HA12216F/HA12221F Series MS Amp. Gain vs. Frequency (HA12216F) (1) 50 VCC = 9.0V TAI (SER mode) 40 30 Gain (dB) 20 MAOUT 10 MSI 0 −10 −20 10 100 1k Frequency (Hz) 10k 100k MS Amp. Gain vs. Frequency (HA12216F) (2) 50 MAOUT 40 30 Gain (dB) 20 MSI 10 0 −10 −20 10 VCC = 9.0V TAI (REP mode) 100 1k Frequency (Hz) 10k 100k Rev.6.00 Jun 15, 2005 page 34 of 52 HA12216F/HA12221F Series MS Sensing Level vs. Frequency (HA12216F) 10 SER L→H SER H→L REP L→H REP H→L VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 0 MS Sensing Level (dB) −10 −20 −30 −40 10 100 1k Frequency (Hz) 10k 100k No-Signal Sensing Time vs. Resistance (HA12216F) 1000 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT NR-OFF f = 5kHz PBOUT No-Signal Sensing Time (ms) 100 10 C10 0.33µ 17 MSOUT VCC R15 1 10k 100k Resistance R15 (Ω) 1M 10M Rev.6.00 Jun 15, 2005 page 35 of 52 HA12216F/HA12221F Series Signal Sensing Time vs. Capacitance (HA12216F) 1000 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT NR-OFF f = 5kHz PBOUT MSOUT Signal Sensing Time (ms) 100 10 1 17 C10 VCC R15 330k 0.1 0.001 0.01 0.1 Capacitance C10 (µF) 1 10 Rev.6.00 Jun 15, 2005 page 36 of 52 HA12216F/HA12221F Series Quiescent Current vs. Supply Voltage (HA12221F) 7 all low 70µ (Other switch is all low) VCC = 9.0V NO SIGNAL Quiescent Current IQ (mA) 6 5 4 6 7 8 9 10 11 Supply Voltage (V) 12 13 Input Amp. Gain vs. Frequency (HA12221F) 26 VCC = 9.0V TAI →PBOUT RAI 22 TAI Gain (dB) 18 RAI 14 10 6 10 100 1k 10k Frequency (Hz) 100k 1M Rev.6.00 Jun 15, 2005 page 37 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Frequency (HA12221F) (1) 1 Vin = 0dB Vin = 10dB Vin = −10dB VCC = 9.0V TAI→PBOUT T.H.D. (%) 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 400Hz HPF + 80kHz LPF 1k Frequency (Hz) 10k 20k Total Harmonic Distortion vs. Frequency (HA12221F) (2) 1 Vin = 0dB Vin = 10dB Vin = −10dB VCC = 9.0V RAI→PBOUT T.H.D. (%) 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 400Hz HPF + 80kHz LPF 1k Frequency (Hz) 10k 20k Rev.6.00 Jun 15, 2005 page 38 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Output Level (HA12221F) (1) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 1 T.H.D. (%) 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 Total Harmonic Distortion vs. Output Level (HA12221F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V RAI→PBOUT 0dB = 300mVrms 1 T.H.D. (%) 0.1 0.01 −15 −10 −5 0 5 10 Output Level Vout (dB) 15 20 Rev.6.00 Jun 15, 2005 page 39 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Supply Voltage (HA12221F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) TAI→PBOUT = 300mVrms 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Total Harmonic Distortion vs. Supply Voltage (HA12221F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) RAI→PBOUT = 300mVrms 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 40 of 52 HA12216F/HA12221F Series Signal Handling (HA12221F) 40 35 30 25 20 15 10 5 0 6 TAI RAI TAI →PBOUT = 300mVrms = 0dB RAI f = 1kHz T.H.D. = 1% Vomax (dB) 7 8 9 10 11 12 13 Supply Voltage (V) 14 15 16 Signal to Noise Ratio vs. Supply Voltage (HA12221F) 90 85 Signal to Noise Ratio (dB) 80 75 TAI RAI 70 TAI →PBOUT = 300mVrms = 0dB RAI f = 1kHz CCIR/ARM filter 65 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 41 of 52 HA12216F/HA12221F Series Equalizer Amp. Gain vs. Frequency (HA12221F) 80 70 60 50 EQ Gain (dB) 40 30 120µ 70µ 20 10 0 −10 −20 10 VCC = 9.0V FIN→EQOUT 100 1k 10k Frequency (Hz) 100k 1M Total Harmonic Distortion vs. Frequency (HA12221F) 1 120µ 70µ VCC = 9.0V FIN→EQOUT 0dB = 60mVrms Vout = +20dB T.H.D. (%) 0.1 0.01 30kHz LPF 0.001 100 400Hz HPF + 30kHz LPF 400Hz HPF + 80kHz LPF 1k Frequency (Hz) 10k 20k Rev.6.00 Jun 15, 2005 page 42 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Output Level (HA12221F) (1) 10 1 T.H.D. (%) 0.1 0.01 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 0dB = 60mVrms 120µ 0.001 −5 0 5 10 15 20 25 Output Level Vout (dB) 30 35 Total Harmonic Distortion vs. Output Level (HA12221F) (2) 10 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) VCC = 9.0V FIN→EQOUT 1 0dB = 60mVrms 70µ T.H.D. (%) 0.1 0.01 0.001 −5 0 5 10 15 20 25 Output Level Vout (dB) 30 35 Rev.6.00 Jun 15, 2005 page 43 of 52 HA12216F/HA12221F Series Total Harmonic Distortion vs. Supply Voltage (HA12221F) (1) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms = 0dB Vout = +20dB 120µ 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Total Harmonic Distortion vs. Supply Voltage (HA12221F) (2) 1 100Hz (30kHz LPF) 1kHz (400Hz HPF + 30kHz LPF) 10kHz (400Hz HPF + 80kHz LPF) FIN→EQOUT = 60mVrms = 0dB Vout = +20dB 70µ 0.1 T.H.D. (%) 0.01 0.001 5 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 44 of 52 HA12216F/HA12221F Series Signal Handling (HA12221F) 45 FIN 120µ FIN 70µ RIN 120µ RIN 70µ FIN →EQOUT RIN 0dB = 60mVrms f = 1kHz T.H.D. = 1% 40 35 Vomax (dB) 30 25 20 15 6 8 10 12 Supply Voltage (V) 14 16 Signal to Noise Ratio vs. Supply Voltage (HA12221F) 80 75 70 65 60 55 50 45 40 5 120µ 70µ FIN→EQOUT 0dB = 60mVrms f = 1kHz DIN-AUDIO filter Signal to Noise Ratio (dB) 6 7 8 9 10 11 Supply Voltage (V) 12 13 14 Rev.6.00 Jun 15, 2005 page 45 of 52 HA12216F/HA12221F Series Ripple Rejection Ratio vs. Frequency (HA12221F) (1) 20 10 VCC = 9.0V Vin = 100mVrms PBOUT Ripple Rejection Ratio R.R.R. (dB) 0 −10 −20 −30 −40 −50 −60 −70 −80 10 100 1k Frequency (Hz) PBOUT (RAI) PBOUT (TAI) 10k 100k Ripple Rejection Ratio vs. Frequency (HA12221F) (2) 20 10 VCC = 9.0V Vin = 100mVrms EQOUT FOR mode Ripple Rejection Ratio R.R.R. (dB) 0 −10 −20 −30 −40 −50 −60 −70 −80 10 EQOUT (120µ) EQOUT (70µ) 100 1k Frequency (Hz) 10k 100k Rev.6.00 Jun 15, 2005 page 46 of 52 HA12216F/HA12221F Series Channel Separation vs. Frequency (HA12221F) (1) VCC = 9.0V FIN→PBOUT 0dB = 300mVrms Vout = +12dB −30 −40 Channel Separation (dB) −50 −60 R→L −70 L→R −80 10 100 1k Frequency (Hz) 10k 100k Channel Separation vs. Frequency (HA12221F) (2) 0 −10 −20 VCC = 9.0V RAI→PBOUT Vin = +12dB Channel Separation (dB) −30 −40 −50 −60 −70 −80 −90 −100 10 R→L L→R 100 1k 10k Frequency (Hz) 100k 1M Rev.6.00 Jun 15, 2005 page 47 of 52 HA12216F/HA12221F Series Crosstalk (FIN→RAI) vs. Frequency (HA12221F) FIN RIN VCC = 9.0V 0dB = 300mVrms Vout = +12dB −50 −60 Crosstalk (dB) −70 −80 −90 −100 10 100 10k 1k Frequency (Hz) 100k 1M −20 −30 −40 −50 VCC = 9.0V PBOUT Vin = +12dB Crosstalk vs. Frequency (HA12221F) RAI→TAI Crosstalk (dB) −60 −70 −80 −90 −100 −110 −120 10 100 TAI→RAI 1k Frequency (Hz) 10k 100k Rev.6.00 Jun 15, 2005 page 48 of 52 HA12216F/HA12221F Series MS Amp. Gain vs. Frequency (HA12221F) (1) 50 VCC = 9.0V TAI (SER mode) 40 Gain (dB) 30 20 MAOUT 10 MSI 0 10 100 1k Frequency (Hz) 10k 100k MS Amp. Gain vs. Frequency (HA12221F) (2) 50 VCC = 9.0V TAI (REP mode) 40 MAOUT Gain (dB) 30 20 MSI 10 0 10 100 1k Frequency (Hz) 10k 100k Rev.6.00 Jun 15, 2005 page 49 of 52 HA12216F/HA12221F Series MS Sensing Level vs. Frequency (HA12221F) 10 SER L→H SER H→L REP L→H REP H→L VCC = 9.0V TAI→PBOUT 0dB = 300mVrms 0 MS Sensing Level (dB) −10 −20 −30 −40 10 100 1k Frequency (Hz) 10k 100k No-Signal Sensing Time vs. Resistance (HA12221F) 1000 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT f = 5kHz No-Signal Sensing Time (ms) 100 PBOUT 10 C10 0.33µ 17 MSOUT VCC R15 1 10k 100k Resistance R15 (Ω) 1M 10M Rev.6.00 Jun 15, 2005 page 50 of 52 HA12216F/HA12221F Series Signal Sensing Time vs. Capacitance (HA12221F) 1000 SER 0dB SER −5dB SER −10dB REP 0dB REP −5dB REP −10dB VCC = 9.0V TAI→PBOUT f = 5kHz Signal Sensing Time (ms) 100 10 PBOUT MSOUT 1 17 C10 VCC R15 330k 0.1 0.001 0.01 0.1 Capacitance C10 (µF) 1 10 Rev.6.00 Jun 15, 2005 page 51 of 52 HA12216F/HA12221F Series Package Dimensions JEITA Package Code P-LQFP40-7x7-0.65 RENESAS Code PLQP0040JB-A Previous Code FP-40B MASS[Typ.] 0.2g HD *1 D 21 NOTE) 1. DIMENSIONS"*1"AND"*2" DO NOT INCLUDE MOLD FLASH 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 30 31 20 bp b1 Reference Symbol Dimension in Millimeters Min Nom 7.0 7.0 1.40 8.8 8.8 9.0 9.0 9.2 9.2 1.70 0.08 0.20 0.13 0.25 0.22 0.12 0.17 0.15 0° 0.65 0.13 0.10 0.575 0.575 0.40 0.50 1.0 0.60 8° 0.22 0.22 0.30 Max c1 HE E c D E A2 *2 ZE Terminal cross section HD HE A A1 bp 40 11 1 ZD Index mark 10 F b1 c A A2 c c1 θ θ e x y ZD ZE L L1 A1 L L1 Detail F e *3 bp y x M Rev.6.00 Jun 15, 2005 page 52 of 52 Sales Strategic Planning Div. Keep safety first in your circuit designs! Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: (408) 382-7500, Fax: (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: (1628) 585-100, Fax: (1628) 585-900 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: 2265-6688, Fax: 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: (2) 2715-2888, Fax: (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: (21) 6472-1001, Fax: (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: 6213-0200, Fax: 6278-8001 http://www.renesas.com © 2005. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon 2.0