HA1630S07CMEL-E

Data Sheet HA1630S04/05/06 Series Ultra-Small Low Voltage Operation CMOS Single Operational Amplifier R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Description The HA1630S04/05/06 are high slew rate single CMOS Operational Amplifiers realizing low voltage operation, low input offset voltage and low supply current. In addition to a low operating voltage from 1.8V, these device output can achieve full swing output voltage capability extending to either supply. Available in an ultra-small CMPAK-5 package that occupies only 1/8 the area of the SOP-8 package. Features • Low power and single supply operation • Low input offset voltage • Low supply current • High slew rate • Maximum output voltage • Low input bias current VDD = 1.8 to 5.5 V VIO = 4.0 mV Max IDD = 200 μA Typ (HA1630S04) IDD = 400 μA Typ (HA1630S05) IDD = 800 μA Typ (HA1630S06) SR = 2 V/μs Typ (HA1630S04) SR = 4 V/μs Typ (HA1630S05) SR = 8 V/μs Typ (HA1630S06) VOH = 2.9 V Min (at VDD = 3.0 V) IIB = 1 pA Typ Ordering Information Type No. HA1630S04CM HA1630S04LP HA1630S05CM HA1630S05LP HA1630S06CM HA1630S06LP R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Package Name CMPAK-5 MPAK-5 CMPAK-5 MPAK-5 CMPAK-5 MPAK-5 Package Code PTSP0005ZC-A PLSP0005ZB-A PTSP0005ZC-A PLSP0005ZB-A PTSP0005ZC-A PLSP0005ZB-A Page 1 of 24 HA1630S04/05/06 Series Pin Arrangement VDD 5 VOUT 4 + − 1 2 3 VIN(+) VSS VIN(–) Equivalent Circuit VDD VIN(–) VOUT VIN(+) VSS R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 2 of 24 HA1630S04/05/06 Series Absolute Maximum Ratings (Ta = 25°C) Items Supply voltage Differential input voltage Input voltage Power dissipation Operating temp. Range Storage temp. Range Note: Symbol Ratings 7 –VDD to +VDD –0.3 to +VDD 200 –40 to +85 –55 to +125 VDD VIN(diff) VIN PT Topr Tstg Unit V V V mW °C °C Note 1 1. Do not apply Input Voltage exceeding VDD or 7 V. Electrical Characteristics (VDD = 3.0 V, Ta = 25°C) Items Input offset voltage Input offset current Input bias current Symbol VIO IIO IIB Min — — — Typ — (1.0) (1.0) Max 4.0 — — Unit mV pA pA Output high voltage Output source current VOH IO SOURCE 2.9 100 — 200 — — V μA 200 400 — — — — –0.05 to 2.1 0 to 1.9 — — — 60 — — — 50 50 — — 400 800 — (5.0) (6.0) (6.5) — — (2.0) (4.0) (8.0) 90 (2.1) (3.3) (3.6) 70 70 200 400 — — 0.1 — — — — — — — — — — — — — — 400 800 — 800 1700 Output low voltage Output sink current VOL IO SINK Common mode input voltage range VCM Slew rate SR Voltage gain Gain bandwidth product AV BW Power supply rejection ratio Common mode rejection ratio Supply current PSRR CMRR IDD V mA V V/μs dB MHz dB dB μA Test Condition Vin = 1.5 V Vin = 1.5 V Vin = 1.5 V RL = 100 kΩ VOH = 2.5 V (HA1630S04) VOH = 2.5 V (HA1630S05) VOH = 2.5 V (HA1630S06) RL = 100 kΩ VOL = 0.5 V (HA1630S04) VOL = 0.5 V (HA1630S05) VOL = 0.5 V (HA1630S06) (HA1630S04, HA1630S05) (HA1630S06) CL = 20 pF (HA1630S04) CL = 20 pF (HA1630S05) CL = 20 pF (HA1630S06) CL = 20 pF (HA1630S04) CL = 20 pF (HA1630S05) CL = 20 pF (HA1630S06) RL = ∞ (HA1630S04) RL = ∞ (HA1630S05) RL = ∞ (HA1630S06) Notes: 1. In the case of continuous current flow, use a sink current of under 4 mA. 2. ( ) : Design specification R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 3 of 24 HA1630S04/05/06 Series Table of Graphs Electrical Characteristics Supply current IDD vs Supply voltage vs Ambient temperature Output high voltage VOH vs Output source current vs Supply voltage Output source current IO SOURCE vs Ambient temperature Output low voltage VOL vs Output sink current Output sink current IO SINK vs Ambient temperature Input offset voltage VIO Distribution vs Supply voltage vs Ambient temperature vs Ambient temperature VCM Common mode input voltage range HA1630S04 Figure HA1630S05 Figure HA1630S06 Figure 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 3-1 3-2 3-3 3-4 3-5 3-6 3-7 3-8 3-9 3-10 3-11 Test Circuit 2 4 6 5 6 1 7 Power supply rejection ratio PSRR vs Frequency 1-12 2-12 3-12 1 Common mode rejection ratio CMRR vs Frequency 1-13 2-13 3-13 7 Voltage gain & phase angle Input bias current AV vs Frequency 1-14 2-14 3-14 10 IIB SRr SRf 1-15 1-16 1-17 1-18 2-15 2-16 2-17 2-18 3-15 3-16 3-17 3-18 3 Slew Rate (rising) Slew Rate (falling) Slew rate vs Ambient temperature vs Input voltage vs Ambient temperature vs Ambient temperature Large signal transient response 1-19 2-19 3-19 Small signal transient response 1-20 2-20 3-20 vs. Output voltage p-p vs. Output voltage p-p 1-21 1-22 2-21 2-22 3-21 3-22 vs Frequency 1-23 2-23 3-23 vs Frequency 1-24 2-24 3-24 Total harmonic distortion + noise (0 dB) (40 dB) Maximum p-p output voltage Voltage noise density R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 9 8 Page 4 of 24 HA1630S04/05/06 Series Main Characteristics (HA1630S04) Figure 1-1. HA1630S04 Supply Current vs. Supply Voltage 400 Ta = 25°C Supply Current IDD (μA) Supply Current IDD (μA) 400 Figure 1-2. HA1630S04 Supply Current vs. Ambient Temperature 300 200 100 0 1 2 3 4 5 Supply Voltage VDD (V) VDD = 5.5 V VDD = 3.0 V 300 VDD = 1.8 V 200 100 0 −40 6 5 VDD = 5.5 V 4 3 VDD = 3.0 V 2 VDD = 1.8 V 1 Output High Voltage VOH (V) Output High Voltage VOH (V) Ta = 25°C 100 Figure 1-4. HA1630S04 Output High Voltage vs. Supply Voltage Figure 1-3. HA1630S04 Output High Voltage vs. Output Source Current 6 −20 0 20 40 60 80 Ambient Temperature Ta (°C) 6 Ta = 25°C VDD = 3.0 V RL = 100 kΩ 5 4 3 2 1 0 0 100 200 300 Output Source Current IOSOURCE (μA) 1 2 3 4 5 Supply Voltage VDD (V) 6 Output Source Current IOSOURCE (μA) Figure 1-5. HA1630S04 Output Source Current vs. Ambient Temperature 400 300 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 200 100 0 −40 −20 0 20 40 60 80 100 Ambient Temperature Ta (°C) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 5 of 24 HA1630S04/05/06 Series Figure 1-7. HA1630S04 Output Sink Current vs. Ambient Temperature 10 1.5 VDD = 5.5 V Output Sink Current IOSINK (mA) Output Low Voltage VOL (V) Figure 1-6. HA1630S04 Output Low Voltage vs. Output Sink Current VDD = 3.0 V 1.0 VDD = 1.8 V 0.5 0 0 2 4 Output Sink Current IOSINK (mA) VDD = 5.5 V VDD = 3.0 V 8 VDD = 1.8 V 6 4 2 0 −40 6 Percentage (%) 40 Ta = 25°C VDD = 3.0 V 30 20 10 0 −4 −3 −2 −1 0 1 2 3 Input Offset Voltage VIO (mV) 4 4 Ta = 25°C VIN = 0.5 V 3 2 1 0 −1 −2 −3 −4 1 2 Common Mode Input Voltage VCM (V) Input Offset Voltage VIO (mV) 6 3.0 4 VDD = 1.8 V, VIN = 0.9 V 2 VDD = 3.0 V, VIN = 1.5 V 1 0 −1 VDD = 5.5 V, VIN = 2.75 V −2 −3 −4 −40 3 4 5 Supply Voltage VDD (V) Figure 1-11. HA1630S04 Common Mode Input Voltage vs. Ambient Temperature Figure 1-10. HA1630S04 Input Offset Voltage vs. Ambient Temperature 3 100 Figure 1-9. HA1630S04 Input Offset Voltage vs. Supply Voltage Input Offset Voltage VIO (mV) Figure 1-8. HA1630S04 Input Offset Voltage Distribution −20 0 20 40 60 80 Ambient Temperature Ta (°C) −20 0 20 40 60 80 Ambient Temperature Ta (°C) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 100 2.0 VDD = 3.0 V 1.0 0 −1.0 −40 −20 0 20 40 60 80 100 Ambient Temperature Ta (°C) Page 6 of 24 HA1630S04/05/06 Series Power Supply Rejection Ratio PSRR (dB) Figure 1-12. HA1630S04 Power Supply Rejection Ratio vs. Frequency 100 Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF 80 60 40 20 0 10 100 1k 10k 100k 1M 10M Frequency f (Hz) Common Mode Rejection Ratio CMRR (dB) Figure 1-13. HA1630S04 Common Mode Rejection Ratio vs. Frequency 100 Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF 80 60 40 20 0 10 100 1k 10k 100k 1M 10M Frequency f (Hz) Figure 1-14. HA1630S04 Open Loop Voltage Gain and Phase Angle vs. Frequency Open Loop Voltage Gain AVOL (dB) 80 Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF Open Loop Voltage Gain 60 135 90 40 Phase Angle 20 45 0 Phase Margin: 57 deg 0 −45 −20 −40 10 180 Phase Angle (deg) 225 100 100 1k 10k 100k 1M −90 10M Frequency f (Hz) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 7 of 24 HA1630S04/05/06 Series 200 VDD = 3.0 V 100 0 −100 −200 0 Figure 1-16. HA1630S04 Input Bias Current vs. Input Voltage Input Bias Current IIB (pA) Input Bias Current IIB (pA) Figure 1-15. HA1630S04 Input Bias Current vs. Ambient Temperature 25 50 75 Ambient Temperature Ta (°C) 200 100 0 −100 −200 100 Figure 1-17. HA1630S04 Slew Rate (rising) vs. Ambient Temperature Slew Rate SRf (V/μs) Slew Rate SRr (V/μs) 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 5 VDD = 5.5 V 4 VDD = 3.0 V VDD = 1.8 V 2 1 0 −40 0 Figure 1-18. HA1630S04 Slew Rate (falling) vs. Ambient Temperature 5 3 Ta = 25°C VDD = 3.0 V −20 0 20 40 60 80 100 VDD = 5.5 V VDD = 3.0 V VDD = 1.8 V 4 3 2 1 0 −40 −20 0 20 40 60 80 Ambient Temperature Ta (°C) Ambient Temperature Ta (°C) Figure 1-19. HA1630S04 Large Signal Transient Response Figure 1-20. HA1630S04 Small Signal Transient Response 2.0 V Vin = 2.1 Vp-p, 250 kHz Ta = 25°C VDD = 3.0 V RL = 100 kΩ CL = 20 pF 1.6 V Vin = 0.2 Vp-p, 250 kHz 0V 1.4 V 2.0 V 1.6 V 0V 1.4 V R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 100 Ta = 25°C VDD = 3.0 V RL = 100 kΩ CL = 20 pF Page 8 of 24 HA1630S04/05/06 Series Figure 1-21. HA1630S04 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 VDD = 3.0 V Ta = 25°C Gain = 0 dB 1 T.H.D. + Noise (%) T.H.D. + Noise (%) 10 Figure 1-22. HA1630S04 Total Harmonic Distortion + Noise vs. Output Voltage p-p f = 10 kHz f = 1 kHz f = 100 Hz 0.1 0.01 0.001 1 f = 10 kHz f = 1 kHz f = 100 Hz 0.1 0.01 V = 3.0 V DD Ta = 25°C Gain = 40 dB 0.001 0 0.5 1.0 1.5 2.0 2.5 3.0 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Voltage Output Vout p-p (V) Figure 1-23. HA1630S04 Voltage Output p-p vs. Frequency 3.5 Ta = 25°C VDD = 3.0 V 3.0 2.5 Gain = 40 dB, VIN = 0.03 Vp-p 2.0 Gain = 0 dB, VIN = 2.0 Vp-p 1.5 1.0 0.5 0 1k Voltage Noise Density (nVms/√Hz) Gain = 20 dB, VIN = 0.3 Vp-p 10k 100k Frequency f (Hz) 1M 10M Figure 1-24. HA1630S04 Voltage Noise Density vs. Frequency 200 VDD = 3.0 V Ta = 25°C Gain = 40 dB RS = 1 kΩ 160 120 80 40 0 100 1k 10k Frequency f (Hz) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 9 of 24 HA1630S04/05/06 Series Main Characteristics (HA1630S05) Figure 2-1. HA1630S05 Supply Current vs. Supply Voltage Figure 2-2. HA1630S05 Supply Current vs. Ambient Temperature 800 Ta = 25°C Supply Current IDD (μA) Supply Current IDD (μA) 800 600 400 200 0 1 2 3 4 5 Supply Voltage VDD (V) VDD = 5.5 V VDD = 3.0 V 600 VDD = 1.8 V 400 200 0 −40 6 6 Ta = 25°C VDD = 5.5 V 5 4 3 VDD = 3.0 V 2 VDD = 1.8 V 1 0 100 Figure 2-4. HA1630S05 Output High Voltage vs. Supply Voltage Output High Voltage VOH (V) Output High Voltage VOH (V) Figure 2-3. HA1630S05 Output High Voltage vs. Output Source Current −20 0 20 40 60 80 Ambient Temperature Ta (°C) 6 Ta = 25°C VDD = 3.0 V 5 4 RL = 100 kΩ RL = 20 kΩ 3 2 1 0 100 200 300 400 500 Output Source Current IOSOURCE (μA) 1 2 3 4 5 Supply Voltage VDD (V) 6 Output Source Current IOSOURCE (μA) Figure 2-5. HA1630S05 Output Source Current vs. Ambient Temperature 800 VDD = 5.5 V VDD = 3.0 V 600 VDD = 1.8 V 400 200 0 −40 −20 0 20 40 60 80 100 Ambient Temperature Ta (°C) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 10 of 24 HA1630S04/05/06 Series Figure 2-7. HA1630S05 Output Sink Current vs. Ambient Temperature 10 1.5 Output Sink Current IOSINK (mA) Output Low Voltage VOL (V) Figure 2-6. HA1630S05 Output Low Voltage vs. Output Sink Current VDD = 5.5 V VDD = 3.0 V 1.0 VDD = 1.8 V 0.5 0 0 2 4 6 Output Sink Current IOSINK (mA) VDD = 5.5 V VDD = 3.0 V 8 VDD = 1.8 V 6 4 2 0 −40 8 Percentage (%) 40 Ta = 25°C VDD = 3.0 V 30 20 10 0 −4 −3 −2 −1 0 1 2 3 Input Offset Voltage VIO (mV) 4 4 Ta = 25°C VIN = 0.5 V 3 2 1 0 −1 −2 −3 −4 1 2 Common Mode Input Voltage VCM (V) Input Offset Voltage VIO (mV) 6 3.0 4 VDD = 1.8 V, VIN = 0.5 V 2 VDD = 3.0 V, VIN = 1.5 V 1 0 −1 VDD = 5.5 V, VIN = 2.75 V −2 −3 −4 −40 3 4 5 Supply Voltage VDD (V) Figure 2-11. HA1630S05 Common Mode Input Voltage vs. Ambient Temperature Figure 2-10. HA1630S05 Input Offset Voltage vs. Ambient Temperature 3 100 Figure 2-9. HA1630S05 Input Offset Voltage vs. Supply Voltage Input Offset Voltage VIO (mV) Figure 2-8. HA1630S05 Input Offset Voltage Distribution −20 0 20 40 60 80 Ambient Temperature Ta (°C) −20 0 20 40 60 80 Ambient Temperature Ta (°C) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 100 2.0 VDD = 3.0 V 1.0 0 −1.0 −40 −20 0 20 40 60 80 100 Ambient Temperature Ta (°C) Page 11 of 24 HA1630S04/05/06 Series Power Supply Rejection Ratio PSRR (dB) Figure 2-12. HA1630S05 Power Supply Rejection Ratio vs. Frequency 100 Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF 80 60 40 20 0 10 100 1k 10k 100k 1M 10M Frequency f (Hz) Common Mode Rejection Ratio CMRR (dB) Figure 2-13. HA1630S05 Common Mode Rejection Ratio vs. Frequency 100 Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF 80 60 40 20 0 10 100 1k 10k 100k 1M 10M Frequency f (Hz) Figure 2-14. HA1630S05 Open Loop Voltage Gain and Phase Angle vs. Frequency Open Loop Voltage Gain AVOL (dB) Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF Open Loop Voltage Gain 80 60 135 90 40 20 45 Phase Angle 0 0 Phase Margin: 55 deg −45 −20 −40 10 180 Phase Angle (deg) 225 100 100 1k 10k 100k 1M −90 10M Frequency f (Hz) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 12 of 24 HA1630S04/05/06 Series 200 VDD = 3.0 V 100 0 −100 −200 0 Figure 2-16. HA1630S05 Input Bias Current vs. Input Voltage Input Bias Current IIB (pA) Input Bias Current IIB (pA) Figure 2-15. HA1630S05 Input Bias Current vs. Ambient Temperature 25 50 75 Ambient Temperature Ta (°C) 200 Ta = 25°C VDD = 3.0 V 100 0 −100 −200 100 0 Figure 2-17. HA1630S05 Slew Rate (rising) vs. Ambient Temperature VDD = 5.5 V Slew Rate SRf (V/μs) Slew Rate SRr (V/μs) 2.5 3.0 10 8 VDD = 3.0 V VDD = 1.8 V 4 2 0 −40 1.0 1.5 2.0 Input Voltage VIN (V) Figure 2-18. HA1630S05 Slew Rate (falling) vs. Ambient Temperature 10 6 0.5 −20 0 20 40 60 80 100 VDD = 5.5 V 8 6 VDD = 3.0 V VDD = 1.8 V 4 2 0 −40 −20 0 20 40 60 80 Ambient Temperature Ta (°C) Ambient Temperature Ta (°C) Figure 2-19. HA1630S05 Large Signal Transient Response Figure 2-20. HA1630S05 Small Signal Transient Response 2.0 V VIN = 2.1 Vp-p, 500 kHz Ta = 25°C VDD = 3.0 V RL = 100 kΩ CL = 20 pF 1.6 V VIN = 0.2 Vp-p, 500 kHz 0V 1.4 V 2.0 V 1.6 V 0V 1.4 V R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 100 Ta = 25°C VDD = 3.0 V RL = 100 kΩ CL = 20 pF Page 13 of 24 HA1630S04/05/06 Series Figure 2-21. HA1630S05 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 VDD = 3.0 V Ta = 25°C Gain = 0 dB 1 T.H.D. + Noise (%) T.H.D. + Noise (%) 10 Figure 2-22. HA1630S05 Total Harmonic Distortion + Noise vs. Output Voltage p-p f = 10 kHz f = 1 kHz f = 100 Hz 0.1 0.01 0.001 0.1 0.01 0.001 0 0.5 1.0 1.5 2.0 2.5 3.0 f = 10 kHz f = 1 kHz f = 100 Hz 1 VDD = 3.0 V Ta = 25°C Gain = 40 dB 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Voltage Output Vout p-p (V) Figure 2-23. HA1630S05 Voltage Output p-p vs. Frequency 3.5 Ta = 25°C VDD = 3.0 V 3.0 Gain = 40 dB, VIN = 0.03 Vp-p 2.5 Gain = 20 dB, VIN = 0.3 Vp-p 2.0 Gain = 0 dB, VIN = 2.0 Vp-p 1.5 1.0 0.5 0 1k 10k 100k Frequency f (Hz) 1M 10M Figure 2-24. HA1630S05 Voltage Noise Density vs. Frequency Voltage Noise Density (nVms/√Hz) 200 VDD = 3.0 V Ta = 25°C Gain = 40 dB RS = 1 kΩ 160 120 80 40 0 100 1k 10k Frequency f (Hz) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 14 of 24 HA1630S04/05/06 Series Main Characteristics (HA1630S06) Figure 3-1. HA1630S06 Supply Current vs. Supply Voltage 1600 Ta = 25°C Supply Current IDD (μA) Supply Current IDD (μA) 1600 Figure 3-2. HA1630S06 Supply Current vs. Ambient Temperature 1200 800 400 0 1 2 3 4 5 Supply Voltage VDD (V) VDD = 5.5 V VDD = 3.0 V 1200 VDD = 1.8 V 800 400 0 −40 6 6 Ta = 25°C 5 VDD = 5.5 V 4 VDD = 3.0 V 3 VDD = 1.8 V 2 1 0 100 Figure 3-4. HA1630S06 Output High Voltage vs. Supply Voltage Output High Voltage VOH (V) Output High Voltage VOH (V) Figure 3-3. HA1630S06 Output High Voltage vs. Output Source Current −20 0 20 40 60 80 Ambient Temperature Ta (°C) 6 Ta = 25°C VDD = 3.0 V 5 RL = 100 kΩ RL = 20 kΩ 4 3 2 1 0 200 400 600 800 1000 Output Source Current IOSOURCE (μA) 1 2 3 4 5 Supply Voltage VDD (V) 6 Output Source Current IOSOURCE (μA) Figure 3-5. HA1630S06 Output Source Current vs. Ambient Temperature 1600 VDD = 5.5 V VDD = 3.0 V 1200 VDD = 1.8 V 800 400 0 −40 −20 0 20 40 60 80 100 Ambient Temperature Ta (°C) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 15 of 24 HA1630S04/05/06 Series Figure 3-7. HA1630S06 Output Sink Current vs. Ambient Temperature 12 1.5 Output Sink Current IOSINK (mA) Output Low Voltage VOL (V) Figure 3-6. HA1630S06 Output Low Voltage vs. Output Sink Current VDD = 5.5 V VDD = 3.0 V 1.0 VDD = 1.8 V 0.5 VDD = 5.5 V 10 8 VDD = 3.0 V 6 4 VDD = 1.8 V 2 0 0 2 4 6 8 Output Sink Current IOSINK (mA) 0 −40 10 Percentage (%) 40 Ta = 25°C VDD = 3.0 V 30 20 10 0 −4 −3 −2 −1 0 1 2 3 Input Offset Voltage VIO (mV) 4 4 Ta = 25°C VIN = 0.5 V 3 2 1 0 −1 −2 −3 −4 1 2 Common Mode Input Voltage VCM (V) Input Offset Voltage VIO (mV) 6 3.0 4 VDD = 1.8 V, VIN = 0.5 V 2 VDD = 3.0 V, VIN = 1.5 V 1 0 −1 VDD = 5.5 V, VIN = 2.75 V −2 −3 −4 −40 3 4 5 Supply Voltage VDD (V) Figure 3-11. HA1630S06 Common Mode Input Voltage vs. Ambient Temperature Figure 3-10. HA1630S06 Input Offset Voltage vs. Ambient Temperature 3 100 Figure 3-9. HA1630S06 Input Offset Voltage vs. Supply Voltage Input Offset Voltage VIO (mV) Figure 3-8. HA1630S06 Input Offset Voltage Distribution −20 0 20 40 60 80 Ambient Temperature Ta (°C) −20 0 20 40 60 80 Ambient Temperature Ta (°C) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 100 2.0 VDD = 3.0 V 1.0 0 −1.0 −40 −20 0 20 40 60 80 100 Ambient Temperature Ta (°C) Page 16 of 24 HA1630S04/05/06 Series Power Supply Rejection Ratio PSRR (dB) Figure 3-12. HA1630S06 Power Supply Rejection Ratio vs. Frequency 100 Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF VRIP = 0.1 Vp 80 60 40 20 0 10 100 1k 10k 100k 1M 10M Frequency f (Hz) Common Mode Rejection Ratio CMRR (dB) Figure 3-13. HA1630S06 Common Mode Rejection Ratio vs. Frequency 100 Ta = 25°C VDD = 3.0 V RL = 1 MΩ CL = 20 pF 80 60 40 20 0 10 100 1k 10k 100k 1M 10M Frequency f (Hz) Figure 3-14. HA1630S06 Open Loop Voltage Gain and Phase Angle vs. Frequency Open Loop Voltage Gain AVOL (dB) Ta = 25°C VDD = 3.0 V 180 RL = 1 MΩ CL = 20 pF 135 Open Loop Voltage Gain 80 60 90 40 Phase Angle 45 20 0 Phase Margin: 65 deg −45 −20 −40 10 0 Phase Angle (deg) 225 100 100 1k 10k 100k 1M −90 10M Frequency f (Hz) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 17 of 24 HA1630S04/05/06 Series 200 VDD = 3.0 V 100 0 −100 −200 0 25 50 75 Ambient Temperature Ta (°C) Figure 3-16. HA1630S06 Input Bias Current vs. Input Voltage Input Bias Current IIB (pA) Input Bias Current IIB (pA) Figure 3-15. HA1630S06 Input Bias Current vs. Ambient Temperature 200 100 0 −100 −200 100 Figure 3-17. HA1630S06 Slew Rate (rising) vs. Ambient Temperature 0.5 1.0 1.5 2.0 Input Voltage VIN (V) 2.5 3.0 14 12 Slew Rate SRf (V/μs) Slew Rate SRr (V/μs) 0 Figure 3-18. HA1630S06 Slew Rate (falling) vs. Ambient Temperature 14 VDD = 5.5 V VDD = 3.0 V 10 VDD = 1.8 V 8 6 4 −40 Ta = 25°C VDD = 3.0 V −20 0 20 40 60 80 100 VDD = 5.5 V 12 10 VDD = 3.0 V VDD = 1.8 V 8 6 4 −40 −20 0 20 40 60 80 Ambient Temperature Ta (°C) Ambient Temperature Ta (°C) Figure 3-19. HA1630S06 Large Signal Transient Response Figure 3-20. HA1630S06 Small Signal Transient Response 2.0 V VIN = 1.9 Vp-p, 500 kHz Ta = 25°C VDD = 3.0 V RL = 100 kΩ CL = 20 pF 1.6 V VIN = 0.2 Vp-p, 500 kHz 0V 1.4 V 2.0 V 1.6 V 0V 1.4 V R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 100 Ta = 25°C VDD = 3.0 V RL = 100 kΩ CL = 20 pF Page 18 of 24 HA1630S04/05/06 Series Figure 3-21. HA1630S06 Total Harmonic Distortion + Noise vs. Output Voltage p-p 10 VDD = 3.0 V Ta = 25°C Gain = 0 dB 1 T.H.D. + Noise (%) T.H.D. + Noise (%) 10 Figure 3-22. HA1630S06 Total Harmonic Distortion + Noise vs. Output Voltage p-p f = 10 kHz f = 1 kHz f = 100 Hz 0.1 0.01 1 f = 10 kHz f = 1 kHz f = 100 Hz 0.1 0.01 VDD = 3.0 V Ta = 25°C Gain = 40 dB 0.001 0.001 0 0.5 1.0 1.5 2.0 2.5 3.0 0 Output Voltage Vout p-p (V) 0.5 1.0 1.5 2.0 2.5 3.0 Output Voltage Vout p-p (V) Voltage Output Vout p-p (V) Figure 3-23. HA1630S06 Voltage Output p-p vs. Frequency 3.5 Ta = 25°C VDD = 3.0 V 3.0 2.5 Gain = 40 dB, VIN = 0.03 Vp-p Gain = 20 dB, VIN = 0.3 Vp-p 10k 100k Frequency f (Hz) Gain = 0 dB, VIN = 2.0 Vp-p 2.0 1.5 1.0 0.5 0 1k 1M 10M Figure 3-24. HA1630S06 Voltage Noise Density vs. Frequency Voltage Noise Density (nVms/√Hz) 200 VDD = 3.0 V Ta = 25°C Gain = 40 dB RS = 1 kΩ 160 120 80 40 0 100 1k 10k Frequency f (Hz) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 19 of 24 HA1630S04/05/06 Series Test Circuits 1. Power Supply Rejection Ratio, PSRP & Voltage Offset, VIO VIO VDD VIO = VO − RF = 680 kΩ VDD 2 × RS R S + RF RS = 6.8 kΩ − + PSRR VO RS = 6.8 kΩ VDD PSRR = −20log 2 VDD1 − VDD2 VO1 − VO2 × RS R S + RF Measure VO corresponding to VDD1 = 2.95 V and VDD2 = 3.05 V 2. Supply Current, IDD 3. Input Bias Current, IIB VDD VDD A − + − + VDD VDD 2 2 A 4. Output High Voltage, VOH VOH VDD − + VIN1 VIN2 VIN1 = VDD / 2 − 0.05 V VIN2 = VDD / 2 + 0.05 V VO RL = 100 kΩ 5. Output Low Voltage, VOL VOL VDD VIN1 = VDD / 2 + 0.05 V VIN2 = VDD / 2 − 0.05 V − + VIN1 RL = 100 kΩ VO VIN2 R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 20 of 24 HA1630S04/05/06 Series 6. Output Source Current, IOSOURCE & Output Sink Current, IOSINK VDD IOSOURCE VO = VDD − 0.5 V VIN1 = VDD / 2 − 0.05 V VIN2 = VDD / 2 + 0.05 V − + VIN1 A IOSINK VIN2 VO = + 0.5 V VIN1 = VDD / 2 + 0.05 V VIN2 = VDD / 2 − 0.05 V VO 7. Common Mode Input Voltage, VCM & Common Mode Rejection Ratio, CMRR VDD CMRR RF = 680 kΩ RS = 6.8 kΩ VIN1 − VIN2 VO1 − VO2 CMRR = −20log − + VO RS = 6.8 kΩ × RS RS + RF Measure VO corresponding to VIN1 = 1.45 V and VIN2 = 1.55 V VDD VIN 2 RF = 680 kΩ 8. Total Harmonic Distortion, THD VDD THD RF Gain Variable RS − + VO Gain Variable RF / RS = 20log (100 kΩ / 1 kΩ) = 40 dB RF / RS = 20log (100 kΩ / 100 kΩ) = 0 dB freq = 100 Hz, 1 kHz, 10 kHz 30 kHz LPF ON VIN VSS 9. Slew Rate, SR 10. Gain, AV & Phase, GBW VDD VDD RF = 680 kΩ RS = 6.8 kΩ − + VO 1 MΩ VSS R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 − + 20 pF VO 1 MΩ 20 pF RS = 6.8 kΩ VSS Page 21 of 24 HA1630S04/05/06 Series Package Dimensions JEITA Package Code RENESAS Code Previous Code MASS (Typ) [g] SC-74A PLSP0005ZB-A MPAK-5 / MPAK-5V 0.015 D A e Q E HE L A c LP L1 A3 A x M S A b A2 A A1 y S S b c A-A Section Reference Dimensions in millimeters Symbol Min Nom Max A A1 A2 A3 b c D E e HE L L1 LP x y Q 1.0 0 1.0 ⎯ 0.35 0.11 2.8 1.5 ⎯ 2.5 0.3 0.1 0.2 ⎯ ⎯ ⎯ ⎯ ⎯ 1.1 0.25 0.4 0.16 2.95 1.6 0.95 2.8 ⎯ ⎯ ⎯ ⎯ ⎯ 0.3 1.4 0.1 1.3 ⎯ 0.5 0.26 3.1 1.8 ⎯ 3.0 0.7 0.5 0.6 0.05 0.05 ⎯ © 2013 Renesas Electronics Corporation. All rights reserved. R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 22 of 24 HA1630S04/05/06 Series JEITA Package Code RENESAS Code Previous Code MASS (Typ) [g] SC-88A PTSP0005ZC-A CMPAK-5 / CMPAK-5V 0.006 D A e Q c E HE LP L A A x M L1 S A A2 y S b c A-A Section A3 b A A1 S Reference Dimensions in millimeters Symbol Min Nom Max A A1 A2 A3 b c D E e HE L L1 LP x y Q 0.8 0 0.8 ⎯ 0.15 0.1 1.8 1.15 ⎯ 1.8 0.3 0.1 0.2 ⎯ ⎯ ⎯ ⎯ ⎯ 0.9 0.25 0.22 0.13 2.0 1.25 0.65 2.1 ⎯ ⎯ ⎯ ⎯ ⎯ 0.25 1.1 0.1 1.0 ⎯ 0.3 0.15 2.2 1.35 ⎯ 2.4 0.7 0.5 0.6 0.05 0.05 ⎯ © 2013 Renesas Electronics Corporation. All rights reserved. R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 23 of 24 HA1630S04/05/06 Series Taping & Reel Specification [Taping] Package Code MPAK-5 CMPAK-5 W 8 8 P 4 4 Ao 3.3 2.25 Bo 3.3 2.45 Ko 1.5 1.1 E 1.75 1.75 F 3.5 3.5 D1 1.05 1.05 Maximum Storage No. 3,000 pcs/reel 3,000 pcs/reel 4.0 φ 1.5 Unit: mm E 2.0 Cover tape B0 W F A0 D1 P Tape withdraw direction [Ordering Information] φ178 ± 2 2.0 ± 0.5 W2 9 9 4 ± 0.5 W1 11.4 11.4 0° Tape width 8 8 12 [Reel] Package MPAK-5 CMPAK-5 11.4 φ13 ± 0.5 K0 Ordering Unit 3,000 pcs 9.0 Mark Indication Index band Marking 1 D 1D : HA1630S04 1E : HA1630S05 1F : HA1630S06 = Contorol code ( ⎯ or blank) R03DS0082EJ0200 Rev.2.00 Jan 10, 2014 Page 24 of 24 Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 3. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or 5. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product. the product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products. 11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. http://www.renesas.com SALES OFFICES Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-651-700, Fax: +44-1628-651-804 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Düsseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 301, Tower A, Central Towers, 555 LanGao Rd., Putuo District, Shanghai, China Tel: +86-21-2226-0888, Fax: +86-21-2226-0999 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949 Tel: +65-6213-0200, Fax: +65-6213-0300 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 12F., 234 Teheran-ro, Gangnam-Gu, Seoul, 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 © 2014 Renesas Electronics Corporation. All rights reserved. Colophon 3.0