HA4201CBZ96

DATASHEET OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc HA4201 FN3680 Rev 6.00 March 8, 2007 480MHz, 1x1 Video Crosspoint Switch with Tally Output The HA4201 is a very wide bandwidth 1x1 crosspoint switch ideal for professional video switching, HDTV, computer monitor routing, and other high performance applications. The circuit features very low power dissipation (105mW Enabled, 1mW Disabled), excellent differential gain and phase, and very high off isolation. When disabled, the output is switched to a high impedance state, making the HA4201 ideal for routing matrix equipment. The HA4201 requires no external current source, and features fast switching and symmetric slew rates. The tally output is an open collector PNP transistor to VCC , and is activated whenever EN = 1 to provide an indication of crosspoint selection. For applications which don’t require a TALLY output, please refer to the HA4600 data sheet. Pinout Features • Low Power Dissipation . . . . . . . . . . . . . . . . . . . . . 105mW • Symmetrical Slew Rates . . . . . . . . . . . . . . . . . . 1700V/s • 0.1dB Gain Flatness. . . . . . . . . . . . . . . . . . . . . . . 250MHz • Off Isolation (100MHz) . . . . . . . . . . . . . . . . . . . . . . . 85dB • Differential Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.01% • Differential Phase . . . . . . . . . . . . . . . . . . . . . 0.01 Degrees • High ESD Rating . . . . . . . . . . . . . . . . . . . . . . . . . >1800V • TTL Compatible Enable Input • Open Collector Tally Output • Improved Replacement for GX4201 • Pb-Free Plus Anneal Available (RoHS Compliant) Applications HA4201 (8 LD SOIC) TOP VIEW • Professional Video Switching and Routing • Video Multiplexers • HDTV EN 1 8 GND V- 2 7 IN V+ 3 6 NC OUT 4 5 TALLY • Computer Graphics • RF Switching and Routing • PCM Data Routing Ordering Information Truth Table EN OUT TALLY 0 High Z Off 1 Active On PART NUMBER HA4201CB96 PART MARKING 4201C B HA4201CBZ96 4201C BZ (Note) TEMP. RANGE (°C) PACKAGE PKG. DWG. # 0 to +70 8 Ld SOIC Tape and Reel M8.15 0 to +70 8 Ld SOIC (Pb-free) M8.15 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN3680 Rev 6.00 March 8, 2007 Page 1 of 8 HA4201 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12V Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VSUPPLY Digital Input Current (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . 25mA Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA ESD Rating Human Body Model (Per MIL-STD-883 Method 3015.7) . . . . 1800V Thermal Resistance (Typical, Note 1) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C JA (°C/W) SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170 Maximum Junction Temperature (Die) . . . . . . . . . . . . . . . . . . +175°C Maximum Junction Temperature (Plastic Package) . . . . . . +150°C Maximum Storage Temperature Range . . . . . . . . . -65°C to +150°C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . +300°C (SOIC - Lead Tips Only) Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. JA is measured with the component mounted on an evaluation PC board in free air. 2. If an input signal is applied before the supplies are powered up, the input current must be limited to this maximum value. Electrical Specifications VSUPPLY = ±5V, RL = 10k, VEN = 2.0V, Unless Otherwise Specified TEMP. (°C) MIN TYP MAX UNITS Full 4.5 5.0 5.5 V VEN = 2.0V 25, 70 - 10.5 13 mA VEN = 2.0V 0 - - 14.5 mA VEN = 0.8V 25, 70 - 100 115 A VEN = 0.8V 0 - 100 125 A 25, 70 2.7 2.8 - V 0 2.4 2.5 - V Output Current Full 15 20 - mA Input Bias Current Full - 30 50 A Output Offset Voltage 25 -10 - 10 mV Output Offset Voltage Drift (Note 3) Full - 25 50 V/°C Turn-On Time 25 - 160 - ns Turn-Off Time 25 - 320 - ns Input Logic High Voltage Full 2 - - V Input Logic Low Voltage Full - - 0.8 V PARAMETER TEST CONDITIONS DC SUPPLY CHARACTERISTICS Supply Voltage Supply Current (VOUT = 0V) ANALOG DC CHARACTERISTICS Output Voltage Swing without Clipping VOUT = VIN VIO 20mV SWITCHING CHARACTERISTICS DIGITAL DC CHARACTERISTICS EN Input Current VEN = 0 to 4V Full -2 - 2 A Tally Output High Voltage IOH = 1mA Full 4.7 4.8 - V Tally Off Leakage Current VTALLY = 0V, -5V Full -20 - 20 A Insertion Loss 1VP-P Full - 0.04 0.05 dB -3dB Bandwidth RS = 82, CL = 10pF - 480 - MHz AC CHARACTERISTICS FN3680 Rev 6.00 March 8, 2007 RS = 43, CL = 15pF 25 - 380 - MHz RS = 36, CL = 21pF 25 - 370 - MHz Page 2 of 8 HA4201 Electrical Specifications VSUPPLY = ±5V, RL = 10k, VEN = 2.0V, Unless Otherwise Specified (Continued) TEMP. (°C) MIN TYP MAX UNITS RS = 82, CL = 10pF 25 - 250 - MHz RS = 43, CL = 15pF 25 - 175 - MHz RS = 36, CL = 21pF 25 - 170 - MHz Input Resistance Full 200 400 - k Input Capacitance Full - 1.0 - pF Enabled Output Resistance Full - 15 -  PARAMETER TEST CONDITIONS 0.1dB Flat Bandwidth Disabled Output Capacitance VEN = 0.8V Full - 2.0 - pF Differential Gain 4.43MHz, (Note 3) 25 - 0.01 0.02 % Differential Phase 4.43MHz, (Note 3) 25 - 0.01 0.02 Degrees Off Isolation 1VP-P, 100MHz, VEN = 0.8V, RL = 10 Full - 85 - dB Slew Rate (1.5VP-P, +SR/-SR) RS = 82, CL = 10pF 25 - 1750/1770 - V/s RS = 43, CL = 15pF 25 - 1460/1360 - V/s RS = 36, CL = 21pF 25 - 1410/1360 - V/s Total Harmonic Distortion (Note 3) Full - 0.01 0.1 % Disabled Output Resistance Full - 12 - M NOTE: 3. This parameter is not tested. The limits are guaranteed based on lab characterization, and reflect lot-to-lot variation. AC Test Circuit Application Information General 500 HA4201 VIN 400 RS + CX 75 NOTE: 510 75 HFA1100 VOUT 10k CL = CX + Test Fixture Capacitance. PC Board Layout The frequency response of this circuit depends greatly on the care taken in designing the PC board. The use of low inductance components such as chip resistors and chip capacitors is strongly recommended, while a solid ground plane is a must! Attention should be given to decoupling the power supplies. A large value (10F) tantalum in parallel with a small value (0.1F) chip capacitor works well in most cases. Keep input and output traces as short as possible, because trace inductance and capacitance can easily become the performance limiting items. FN3680 Rev 6.00 March 8, 2007 The HA4201 is a 1x1 crosspoint switch that is ideal for the matrix element in small, high input-to-output isolation switchers and routers. It also excels as an input buffer for routers with a large number of outputs (i.e. each input must connect to a large number of outputs) and delivers performance superior to most video amplifiers at a fraction of the cost. As an input buffer, the HA4201’s low input capacitance and high input resistance provide excellent video terminations when used with an external 75resistor. This crosspoint contains no feedback or gain setting resistors, so the output is a true high impedance load when the IC is disabled (EN = 0). Frequency Response Most applications utilizing the HA4201 require a series output resistor, RS, to tune the response for the specific load capacitance, CL, driven. Bandwidth and slew rate degrade as CL increases (as shown in the Electrical Specification table on page 2), so give careful consideration to component placement to minimize trace length. As an example, -3dB bandwidth decreases to 160MHz for CL = 100pF, RS = 0. In big matrix configurations where CL is large, better frequency response is obtained by cascading two levels of crosspoints in the case of multiplexed outputs (see Figure 2), or distributing the load between two drivers if CL is due to bussing and subsequent stage input capacitance. Page 3 of 8 HA4201 matrix, and the HFA1112 (programmable gain buffer) as the gain of two output driver. Figure 2 details a 16x1 switcher (basically a 16:1 mux) which uses the HA4201 in a cascaded stage configuration to minimize capacitive loading at each output node, thus increasing system bandwidth. Control Signals EN - The ENABLE input is a TTL/CMOS compatible, active high input. When driven low this input forces the output to a true high impedance state and reduces the power dissipation by two orders of magnitude. The EN input has no on-chip pull-up resistor, so it must be connected to a logic high (recommend V+) if the enable function isn’t utilized. Power Up Considerations No signals should be applied to the analog or digital inputs before the power supplies are activated. Latch-up may occur if the inputs are driven at the time of power up. To prevent latch-up, the input currents during power up must not exceed the values listed in the Absolute Maximum Ratings. Tally - The Tally output is an open collector PNP transistor connected to V+. When EN = 1, the PNP transistor is enabled and current is delivered to the load. When the crosspoint is disabled, the Tally output presents a very high impedance to the external circuitry. Several Tally outputs may be wire OR’d together to generate complex control signals, as shown with the HA4404 in the application circuits below. The Tally load may be terminated to GND or to V- as long as the continuous output current doesn’t exceed 3mA (6mA at 50% duty cycle, etc.). Intersil’s Crosspoint Family Intersil offers a variety of 1x1 and 4x1 crosspoint switches. In addition to the HA4201, the 1x1 family includes the HA4600 which is an essentially similar device but without the Tally output. The 4x1 family is comprised of the HA4314, HA4404, and HA4344. The HA4314 is a 14 lead basic 4x1 crosspoint. The HA4404 is a 16 Ld device with Tally outputs to indicate the selected channel. The HA4344 is a 16 Ld crosspoint with synchronized control lines (A0, A1, CS). With synchronization, the control information for the next channel switch can be loaded into the crosspoint without affecting the current state. On a subsequent clock edge the stored control state effects the desired channel switch. Switcher/Router Applications Figure 1 illustrates one possible implementation of a wideband, low-power, 4x4 switcher/router. A 4x4 switcher/router allows any of the four outputs to be driven by any one of the four inputs (e.g. each of the four inputs may connect to a different output, or an input may connect to multiple outputs). This application utilizes the HA4201 for the input buffer, the HA4404 (4x1 crosspoint switch) as the switch INPUT BUFFERS EN SOURCE0 75 OUT HA4201 SWITCH MATRIX RS IN0 IN0 T0 75 RS 75 IN3 IN3 T0 CS HA4404 OUT RS T3 IN0 HA4404 OUT OUT T0 CS HA4404 HA4404 SOURCE2 IN0 CS CS SOURCE1 T0 10k OUT RS T3 IN3 RS T3 IN3 T3 EN SOURCE3 75 OUT HA4201 10k RS OUTPUT BUFFERS (HFA1112 OR HFA1115) X2 + - 75 OUT0 X2 + - 75 OUT1 X2 + - 75 OUT2 X2 + - 75 OUT3 FIGURE 1. 4x4 SWITCHER/ROUTER APPLICATION FN3680 Rev 6.00 March 8, 2007 Page 4 of 8 HA4201 SWITCHING MATRIX SOURCE0 ISOLATION MUX OUTPUT BUFFER IN0 75 IN1 IN2 T0 IN3 SOURCE3 10k 75 T3 OUT IN0 OUT 75 IN1 T0 SOURCE4 IN2 EN RS RS HA4201 T3 IN3 SOURCE7 RS HFA1112 OR HFA1115 75 + HA4404 75 OUT X2 IN0 SOURCE8 75 IN1 IN2 SOURCE11 T0 IN3 75 T3 10k RS OUT IN0 OUT 75 IN1 T0 SOURCE12 IN2 RS EN RS HA4201 T3 IN3 SOURCE15 75 HA4404 FIGURE 2. 16x1 SWITCHER APPLICATION FN3680 Rev 6.00 March 8, 2007 Page 5 of 8 HA4201 VSUPPLY = 5V, TA = 25°C, RL = 10k, Unless Otherwise Specified 1.0 1.25 0.75 1.20 INPUT CAPACITANCE (pF) OUTPUT VOLTAGE (V) Typical Performance Curves 0.5 0.25 0 -0.25 -0.5 1.15 1.10 1.05 1.0 0.95 0.90 0.85 -0.75 0.80 -1.0 0.75 1 TIME (5ns/DIV.) FIGURE 3. LARGE SIGNAL PULSE RESPONSE 0.4 9 0.3 0 -3 RS = 36 CL = 21pF -6 -0.1 -9 -0.3 -0.4 750 RS = 43 CL = 15pF 0 RS = 82 CL = 10pF -0.2 10 100 FREQUENCY (MHz) 500 0.1 -12 1 RS = 36 CL = 21pF 0.2 GAIN (dB) GAIN (dB) RS = 82 R = 43 CL = 10pF S CL = 15pF 3 100 FIGURE 4. INPUT CAPACITANCE vs FREQUENCY 12 6 10 FREQUENCY (MHz) 10 1 100 FREQUENCY (MHz) FIGURE 5. FREQUENCY RESPONSE FIGURE 6. GAIN FLATNESS VIN = 1VP-P RL = 10 -50 OFF ISOLATION (dB) -60 -70 -80 -90 -100 -110 -120 -130 1 10 100 FREQUENCY (MHz) 500 FIGURE 7. OFF ISOLATION FN3680 Rev 6.00 March 8, 2007 Page 6 of 8 500 HA4201 Die Characteristics DIE DIMENSIONS: PASSIVATION: 51 mils x 36 mils x 19 mils 1290m x 910m x 483m Type: Nitride Thickness: 4kÅ 0.5kÅ METALLIZATION: TRANSISTOR COUNT: Type: Metal 1: AlCu (1%)/TiW Thickness: Metal 1: 6kÅ 0.8kÅ 53 SUBSTRATE POTENTIAL (Powered Up): Type: Metal 2: AlCu (1%) Thickness: Metal 2: 16kÅ 1.1kÅ V- Metallization Mask Layout HA4201 EN GND VIN V+ OUT FN3680 Rev 6.00 March 8, 2007 TALLY Page 7 of 8 HA4201 Small Outline Plastic Packages (SOIC) M8.15 (JEDEC MS-012-AA ISSUE C) N 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INDEX AREA 0.25(0.010) M H B M INCHES E SYMBOL -B1 2 3 L SEATING PLANE -A- A D h x 45° -C- e A1 B 0.25(0.010) M C 0.10(0.004) C A M MIN MAX MIN MAX NOTES A 0.0532 0.0688 1.35 1.75 - A1 0.0040 0.0098 0.10 0.25 - B 0.013 0.020 0.33 0.51 9 C 0.0075 0.0098 0.19 0.25 - D 0.1890 0.1968 4.80 5.00 3 E 0.1497 0.1574 3.80 4.00 4 e  B S 0.050 BSC 1.27 BSC - H 0.2284 0.2440 5.80 6.20 - h 0.0099 0.0196 0.25 0.50 5 L 0.016 0.050 0.40 1.27 6 N  NOTES: MILLIMETERS 8 0° 8 8° 0° 1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of Publication Number 95. 7 8° Rev. 1 6/05 2. Dimensioning and tolerancing per ANSI Y14.5M-1982. 3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006 inch) per side. 4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side. 5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 6. “L” is the length of terminal for soldering to a substrate. 7. “N” is the number of terminal positions. 8. Terminal numbers are shown for reference only. 9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch). 10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. © Copyright Intersil Americas LLC 2003-2007. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see www.intersil.com/en/products.html Intersil products are manufactured, assembled and tested utilizing ISO9001 quality systems as noted in the quality certifications found at www.intersil.com/en/support/qualandreliability.html Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com FN3680 Rev 6.00 March 8, 2007 Page 8 of 8